Instruction Manual

Using SCANport CapabilitiesD–14
Publication 1397-5.0 — June, 2001
No. Name Default Value No. Name Default Value
79 Tach Loss Angle 109 118 Trim Range 0%
80 ADV SETUP 2 0 119 Trim Ref Source 0
81 ADV SETUP 3 0 120 Trim Reference 0%
82 ADV SETUP 4 0 121 OCL Enble Src 0 (Register)
126 Inertia Comp Reg 0
83 ADV SETUP 5 0 127 Anlg In 1 Gain 1.000
84 MOP Accel Time 5.0 128 Anlg In 1 Type 0 (O–10V)
85 MOP Decel Time 5.0 129 Anlg In 1 Zero 0
86 MOP Reset Enable 0 130 Anlg In 2 Gain 1.000
87 Preset Speed 1 250 131 Anlg In 2 Zero 0
88 Preset Speed 2 250 132 Anlg In 3 Gain 1.000
89 Preset Speed 3 250 133 Anlg In 3 Type
1 (±10V)
90 Ref 1 Source 0 134 Anlg In 3 Zero 0
91 Ref 2 Source 1 135 Anlg In 4 Gain 1.00
92 Jog Acc/Dec Time 3 136 Anlg In 4 Zero 0
93 Jog Reference 250 137 Freq In Scale 250 kHz
94 Jog Off Dly Time 1 138 Freq In Zero 2.0 kHz
95 REF SETUP 2 0 144 Anlg Out 1 Gain 1.00
96 REF SETUP 3 0 145 Anlg Out 1 Src 0 (Cur Lp Fdbk)
97 REF SETUP 4 0 146 Anlg Out 1 Zero 0
98 REF SETUP 5 0 147 Anlg Out 2 Gain 1.000
99 Min Speed Bypass 0 (Off) 148 Anlg Out 2 Src 0 (Spd Lp Fdbk)
100 Ref Ramp Bypass 0 149 Anlg Out 2 Zero 0
101 Current Compound 0 150 Anlg Out 3 Gain 1.00
102 Inertia Comp Src 0 151 Anlg Out 3 Src 0 (Cur Lp Fdbk)
103 Monitor 1 Delay 10 seconds 152 Anlg Out 3 Type 0 (0 – 10V)
104 Monitor 1 Source 1 153 Anlg Out 4 Gain 1.000
105 Monitor 1 Level 10% 154 Anlg Out 4 Src 0 (Cur Lp Fsdk)
106 Monitor 2 Delay 10 seconds 155 Dig Out 1 Src 0 (Monitor 1 Out)
107 Monitor 2 Source 1 156 Dig Out 1 Type 0 (Normal Open)
108 Monitor 2 Level 10% 157 Dig Out 2 Src 1 (Monitor 2 Out)
109 Normal Inertia 1 seconds 158 Dig Out 2 Type 0 (Normal Open)
110 Reverse Disable 0 (Off) 159 Freq Out Scale 250 kHz
111 S-Curve Rounding 0% 160 Freq Out Src 14 (Zero)
112 AutoTune Bridge 0 (Forward) 161 Freq Out Zero 2 kHz
166 Last Stop Cause 0
113 AutoTune Fld Rng 1.00 167 Open SCR Sens %
114 AutoTune Stab 25 168 Open SCR Trip Pt 800
115 Stop Mode Type 2 (Coast DB) 169 Phase Tst Delta 0 degrees
116 Stop Speed Level 50 170 Phase Tst Bridge 0 (Forward)
117 Trim Mode Type 0 (No Trim) 171 Armature Bridge 0 (Forward)