Instruction Manual

5–99Programming Parameters
Publication 1397-5.0 — June, 2001
Name No. See Page: Name No. See Page:
OCL LeadLag Freq 291 5–91 Reference Owner 218 5–76
OCL Output 018 5–18 Regulator SW Ver 188 5–68
OCL Lead Freq 295 5–93 Reverse Disable 110 5–42
OCL Neg Limit 297 5–93 Run Mask 201 5–72
OCL Pos Limit 296 5–93 Run Owner 215 5–75
OCL Enable 303 5–96 S–Curve Rounding 111 5–43
OCL Ramp Output 019 5–18 Scanport Errors 200 5–71
OCL Ramp Time 298 5–94 Spd Loop Error 021 5–19
OCL Reference TP 020 5–18 Spd Lp Lag Type 076 5–33
OCL Reference 299 5–94 Spd LeadLag Type 074 5–33
OCL Ref Rounding 300 5–95 Spd Lp Lag Freq 075 5–33
OCL Ref Source 301 5–95 Spd Loop Fdbk 022 5–19
OCL Trim Range 302 5–96 Spd Loop Lag Out 023 5–19
Open SCR Sens 275 5–88 Spd Loop Kp 078 5–33
Open SCR Trip Pt 128 5–47 Spd Loop Output 024 5–19
Phase Tst Bridge 276 5–88 Spd Loop Ref 025 5–20
Pos Current Lim 067 5–30 Spd Lp Lead Freq 077 5–33
Pos Curr Lim Src 069 5–31 Spd Ramp In TP 027 5–20
Power Unit Type 186 5–67 Spd Ramp Output 028 5–20
Preset Speed 1,2 and 3 87,88 and 89 5–35 Spd Src Out 026 5–20
PLL Max Error 071 5–32 Speed Pot 029 5–21
Process 1 Par 247 5–82 Stop Owner 214 5–75
Process 1 Scale 248 5–82 Stop Mode Type 115 5–44
Process 1 Text 1 249 5–82 Stop Speed Level 116 5–44
Process 1 Text 2 250 5–82 Tach Loss Angle 079 5–33
Process 1 Text 3 251 5–83 Torque Reference 031 5–21
Process 1 Text 4 252 5–83 Trim Mode Type 117 5–45
Process 1 Text 5 253 5–83 Trim Range 118 5–45
Process 1 Text 6 254 5–83 Trim Reference 120 5–46
Process 1 Text 7 255 5–84 Trim Ref Source 119 5–45
Process 1 Text 8 256 5–84 Trim Output 030 5–21
Process 2 Par 257 5–84
Process 2 Scale 258 5–84
Process 2 Text 1 259 5–85
Process 2 Text 2 260 5–85
Process 2 Text 3 261 5–85
Process 2 Text 4 262 5–85
Process 2 Text 5 263 5–86
Process 2 Text 6 264 5–86
Process 2 Text 7 265 5–86
Process 2 Text 8 266 5–86
Ref Ramp Bypass 100 5–38
Reference Mask 204 5–73
Ref 1 Source 090 5–35
Ref 2 Source 091 5–36