Instruction Manual

ManualsBrandsRockwell Automation ManualsEquipment1397 400-600HP AC Line Filter Kit Inst.

Installation Instructions

1397-5.31 September, 1998

Allen-Bradley

1397

400-600HP AC Line Filter Kit

Cat. Nos. 1397-LF600

User Supplied Items

You must provide three (3) pieces of 600V, 14 AWG wire (each

approximately 1.2 m (4 ft) in length) to connect the kit to the drive’s

AC input bus bars.

What This Option Provides

This option is intended to be applied when the primary of the drive

source power transformer is greater than 2300 V RMS. The AC Line

Filter consists of six capacitors, arranged in three pairs of two

capacitors connected in series. The kit helps to attenuate high voltage

spikes that capacitively couple from the transformer primary to the

secondary. Kit installation consists of connecting the capacitor grid

from the AC input line to ground of the transformer secondary.

What This Kit Contains

Each 1397 - AC Line Filter Kit

Includes: Part No.

◗

(1) Capacitor Assembly 802278-925R

◗

(1) Fuse Block, Triple 49454-19C

◗

(3) Fuse (7.5A, 600V 64876-84N

◗

(1) Wire Harness 802276-924R

◗

(6) Spade Connector (Female) 411066-15B

◗

(2) M6 x 25 Self Threading Screw 419082-100PJM

◗

(6) M4 x 12 Self-Threading Screw 419062-100PGH

◗

(2) M6 Star Washer 419064-101SJ

◗

(6) M4 Flat Washer 19064-1SG

◗

(1) Plastic Cover 802276-920R

Summary of content (6 pages)

PAGE 1
Installation Instructions IN Allen-Bradley 1397 400-600HP AC Line Filter Kit Cat. Nos. 1397-LF600 What This Option Provides This option is intended to be applied when the primary of the drive source power transformer is greater than 2300 V RMS. The AC Line Filter consists of six capacitors, arranged in three pairs of two capacitors connected in series. The kit helps to attenuate high voltage spikes that capacitively couple from the transformer primary to the secondary.
PAGE 2
1397 AC Line Filter Kit Installation ! Mounting ATTENTION: Electric Shock can cause injury or death. Remove all power before working on this product. The drive is at line voltage when connected to incoming AC power. Before proceeding with any installation or troubleshooting activity, disconnect, lockout and tag all incoming power to the drive. Verify with a voltmeter than no voltage exists at input terminals 181 (L1), 182 (L2) and 183 (L3).
PAGE 3
1397 AC Line Filter Kit 3 Figure 1. AC Line Filter Kit Mounting Dimensions 33.3 mm (1.31") 127.0 mm (5.00") 222.2 mm (8.75") 127.0 mm (5.00") 111.1 mm (4.38") 173.1 mm (6.81") 213. 6 mm (8.41") 219. 1 mm (8.63") 252. 6 mm (9.95") Ref. Self-Threading Fastener Hole Size A 3.7 mm (0.147") B 5.6 mm (0.221") 1397-5.
PAGE 4
1397 AC Line Filter Kit Wiring Wire the AC Line Filter Kit as follows: ❐ 1 Cut three (3) pieces of 600V, 14 AWG wire (maximum length 1.2m (4 ft) each). These wires should be of sufficient length to connect the spade terminals on the fuse block to the connectors on each of the drive’s AC input bus bars. Terminate the ends of each wire with the female spade terminals provided in the kit.
PAGE 5
1397 AC Line Filter Kit 5 Figure 2. Wiring the AC Line Filter Kit From AC Line Filter Assembly Drive Input Line Fuses SIDE VIEW FRONT VIEW To Drive AC Input Bus Bars User Supplied Wire Capacitor/Resistor Assembly 181 182 183 Fuse Block C1 C3 C5 C1 C3 C5 Safety Shield AC LINE FILTER KIT Wire Harness 1397-5.
PAGE 6
1397 AC Line Filter Kit Wiring Diagram 181 182 183 Replacement Parts 1397-5.31 September, 1998 C1 0.5uF 0.5uF 680K 680K 7.5A 0.5uF 0.5uF 680K 680K 0.5uF 0.5uF 680K 680K C3 7.5A C5 7.5A DESCRIPTION 0.5 uF Capacitor Resistor Assembly (680 K resistor with attached spade connectors) 7.