Owner manual

Index
I-8
J
Jog 1 Speed, 638, 7-42
Jog 2 Speed, 639, 7-43
Jog Dwell, 711, 7-60
Jog Ramp Enable, 626, 7-39
Jog Speeds, 1-5
Jumper Connections, Circuit Board, 6-18
Jumper Settings
Field Current, 6-19
Main Control Board, 6-19, 6-20
Power Stage Interface Board, 6-19
K
K AC Volts, 740, 7-67
K Armature Volts, 739, 7-67
K Discontinuous Fraction, 745, 7-70
K Discontinuous, 734, 7-66
KF Velocity Loop, 661, 7-47
KI Armature Loop, 736, 7-66
KI Field Loop, 738, 7-66
KI Flux, 672, 7-50
KI Velocity Loop, 659, 7-47
Kn Filter, 692, 7-56
KP Armature Loop, 735, 7-66
KP Field Loop, 737, 7-66
KP Flux, 673, 7-50
KP Velocity Loop, 660, 7-47
L
Line Choke
125–300 HP/250–600 HP Drives, 4-5
40–100 HP/75–200 HP Drives, 3-4, 3-5
Line Current Burden Resistor, 8-10
Line Reactor, 1–30 HP/2–60 HP Drives, 2-4
Linking Source to Sink Parameters, 5-10
Illustration, 5-11
Logic Command 1, 150, 7-25
Logic Command 2, 151, 7-28
Logic Command 3, 152, 7-29
Logic Description, 5-25
Logic Status, 100, 7-16
M
Main Contactor (M1) Control
1–30 HP/2–60 HP Drives, 2-12
125–300 HP/250–600 HP Drives, 4-16
40–100 HP/75–200 HP Drives, 3-17
Main Control Board
1–30 HP/2–60 HP Drives, 2-10
1–30 HP/2–60 HP Drives – Illustration, 2-10
125–300 HP/250–600 HP Drives, 4-10
125–300 HP/250–600 HP Drives – Illustration, 4-10
40–100 HP/75–200 HP Drives, 3-11
40–100 HP/75–200 HP Drives – Illustration, 3-11
Jumper Settings, 6-19, 6-20
Main Control Relay
1–30 HP/2–60 HP Drives, 2-12
125–300 HP/250–600 HP Drives, 4-16
40–100 HP/75–200 HP Drives, 3-17
Maintained Start, 624, 7-38
Manual
Audience, 1-1
Objectives, 1-1
Maximum Current Loop Bandwidth, 742, 7-68
Microbus
1–30 HP/2–60 HP Drives, 2-1
125–300 HP/250–600 HP Drives, 4-1
40–100 HP/75–200 HP Drives, 3-1
Definition, 5-1
Minimum Tapered Current, 667, 7-49
MOP, 1-5
Mop Accel 1, 641, 7-43
Mop Accel 2, 642, 7-43
Mop Accel 3, 643, 7-43
Mop Accel 4, 644, 7-44
MOP Control, Block Diagram, 5-32
Mop Decel 1, 645, 7-44
Mop Decel 2, 646, 7-44
Mop Decel 3, 647, 7-44
Mop Decel 4, 648, 7-45
Mop Max Speed, 649, 7-45
Mop Min Speed, 650, 7-45
Motor and Feedback, Polarity Checks, 8-16
Motor Armature Full Load Amp, 611, 7-34