Owner manual

Index
I-6
Inspection, 1-3
Publication References, 1-10
Receiving Information, 1-3
Specifications, 1-4
Standard Features, 1-2
Storage, 1-3
Unpacking, 1-3
Drive Calibration, Verification, 8-17
Drive Configuration, 5-6
Drive Fault, 101, 7-18
Drive Logic Control, Definition, 5-4
Drive Options, 1-2
Drive Ready/Faulted, 1-5
Drive Tuning
Current Loop Test, 8-19
Current Loop Tune, 8-20
Drive Setup/Autotune/Current, 8-19
Field Flux Tuning, 8-21
Velocity Loop Motor Test, 8-20
Velocity Loop System Test, 8-20
Velocity Loop Tuning, 8-21
Drive Units, Definition, 7-1
Droop Control, Block Diagram, 5-34
Droop Filter (Gain), 658, 7-47
Droop Percent, 657, 7-46
E
ECoast Connections, 6-23
ECOAST Stop
1–30 HP/2–60 HP Drives, 2-12
125–300 HP/250–600 HP Drives, 4-16
40–100 HP/75–200 HP Drives, 3-17
Electrical Specifications, 1-4
Enable/Contingency Coast Stop, 1-5
Encoder, 1-4
Connections, 6-8, 6-34
Encoder PPR, 609, 7-33
Encoder Velocity, 122, 7-24
End Taper Speed, 666, 7-48
Engineering Units, Definition, 7-1
Environment, 6-1
Environmental Specifications, 1-5
ESD Precautions, 1-1
External Inputs Specifications, 1-5
External Outputs Specifications, 1-5
External Overtemperature Delay, 725, 7-63
F
Fast Parameter, Definition, 5-1, 7-1
Fast Sink Parameters, Configuration and Linking, 9-2
Fast Source Parameters, Configuration and Linking, 9-1
Fault Report, 630, 7-41
Fault Select, 623, 7-37
Features of this Drive, 1-2
Feedback Board
125–300 HP/250–600 HP Drives, 4-7
125–300 HP/250–600 HP Drives – Illustration, 4-7
40–100 HP/75–200 HP Drives, 3-7
40–100 HP/75–200 HP Drives – Illustration, 3-7, 3-8
Feedback Board Jumpers
125–300 HP/250–600 HP Drives, 4-7
40–100 HP/75–200 HP Drives, 3-7
Feedback Circuitry, 1–30 HP/2–60 HP Drives, 2-6
Feedback Control, 5-28
Block Diagram, 5-37
Feedback Device Type, 621, 7-36
Feedback Devices Specifications, 1-5
Field Bridge Components
1–30 HP/2–60 HP Drives, 2-5
1–30 HP/2–60 HP Drives – Illustration, 2-5
125–300 HP/250–600 HP Drives, 4-5
125–300 HP/250–600 HP Drives – Illustration, 4-6
40–100 HP/75–200 HP Drives, 3-5
40–100 HP/75–200 HP Drives – Illustration, 3-6
Field Connections, 1–30 HP/2–60 HP Drives, 2-6
Field Control, 1-4
Field Current, 1-4
Jumper Settings, 6-19
Field Current at 0/8 Flux, 677, 7-51
Field Current at 1.0 Flux, 685, 7-54
Field Current at 1/8 Flux, 678, 7-51
Field Current at 2/8 Flux, 679, 7-52
Field Current at 3/8 Flux, 680, 7-52
Field Current at 4/8 Flux, 681, 7-52
Field Current at 5/8 Flux, 682, 7-53
Field Current at 6/8 Flux, 683, 7-53