Installing Your Power Connector Key Kit User guide

ManualsBrandsRockwell Automation ManualsEquipment1394C-SJT_CONN-KEY

Publication 1394-IN023A-EN-P — July 2000

Installation Instructions

Installing Your 1394C Power Connector

Key Kit

Catalog Number 1394C-CONN-KEY

Introduction

This publication provides installation instructions for the 1394C

power connector key kit (catalog number 1394C-CONN-KEY). Use

this document in conjunction with the 1394 Digital AC Multi-Axis

Motion Control System User Manual (publication 1394-5.0).

Systems this Kit Applies to

This kit applies to the following 1394C system modules:

• 1394C-SJT05-A

• 1394C-SJT05-C, -C-RL

• 1394C-SJT05-T, -T-RL

• 1394C-SJT05-L, -L-RL

• 1394C-SJT10-A

• 1394C-SJT10-C, -C-RL

• 1394C-SJT10-T, -T-RL

• 1394C-SJT10-L, -L-RL

What this Kit Contains

This kit contains:

• One key wheel (with six keys).

• One input power connector plug (keyed, with terminals labeled

U, V, W, and PE).

• One logic power connector plug (with terminals labeled W1 and

W2).

• One shunt power connector plug (with jumper and terminals

labeled COL, INT, and DC+).

Figure 1

Kit Contents

W1 W2

UVW

COL INT DC+

Key Wheel

Logic Power

Connector Plug

Input Power

Connector Plug

Shunt Power

Connector Plug

Keys

Jumper

Summary of content (8 pages)

PAGE 1
Installation Instructions Installing Your 1394C Power Connector Key Kit Catalog Number 1394C-CONN-KEY Introduction This publication provides installation instructions for the 1394C power connector key kit (catalog number 1394C-CONN-KEY). Use this document in conjunction with the 1394 Digital AC Multi-Axis Motion Control System User Manual (publication 1394-5.0).
PAGE 2
Installing Your 1394C Power Connector Key Kit Installing the Key Kit Installation of your 1394C power connector key kit involves the replacement of the system module power connector plugs and the insertion of keys into specified system module terminals. The replacement plugs are keyed and labeled to prevent an improper power connection. Follow the procedure starting below to install your 1394C power connector key kit.
PAGE 3
Installing Your 1394C Power Connector Key Kit 3 2. If not already done, label each of the wires leading to the three connectors using small strips of tape. Refer to Figure 2 for connector locations. Figure 2 1394C Power Connectors Logic Power Connector W1 W2 Input Power Connector U V W PE Shunt Power Connector COL INT DC+ 1394 Bottom View Note: If an external shunt resistor is not connected, a jumper is installed (between COL and INT) as shown in the figure above. 3.
PAGE 4
Installing Your 1394C Power Connector Key Kit Replacing the Input Power Connector Plug To replace the input power connector plug: 1. Loosen the screws in the old input power connector plug and remove the wires from each terminal (refer to Figure 2 for connector location). 2. Insert the wires into the replacement connector plug (supplied in the kit) as shown in the table below. Insert the wires Into the connector Tighten to this labeled: plug terminals labeled: torque value: U V W PE U V W PE 0.56-0.
PAGE 5
Installing Your 1394C Power Connector Key Kit 5 Replacing the Shunt Power Connector Plug To replace the shunt power connector plug: 1. If the 1394-SR10A Then: shunt resistor is: Installed Not installed 1. Loosen the screws in the old shunt power connector plug and remove the wires from each terminal (refer to Figure 2 for connector location). 2. Go to main step 2. Go to main step 3. 2.
PAGE 6
Installing Your 1394C Power Connector Key Kit Re-applying Power to Your 1394C System To re-apply power to your 1394C system: 1. Re-connect the three connector plugs as shown in the table below (refer to Figure 2 for connector locations). Connect the plug Into this system module connector: labeled: W1 W2 U V W PE COL INT DC+ Input logic connector Input power connector Shunt power connector 2. Re-apply power to your system. 3. Check for proper operation.
PAGE 7
Installing Your 1394C Power Connector Key Kit 7 Publication 1394-IN023A-EN-P — July 2000
PAGE 8
For more information refer to our web site: www.ab.com/motion For Rockwell Automation Technical Support information refer to: www.rockwellautomation.com/support or Tel: (1) 440.646.3434 Publication 1394-IN023A-EN-P — July 2000 195891 Copyright 2000 Rockwell International. All Rights Reserved. Printed in USA.