Manual

ManualsBrandsRockwell Automation ManualsEquipment1336T FORCE to PowerFlex 700S Phase II Drive Conversion Guide

1336 FORCE™ To PowerFlex® 700S Phase II AC Drive Conversion Guide

Environment Altitude: 1000 m (3300 ft) max. without derating. 1000 m (3300 ft.) max. without derating.

Surrounding Air Temp.

without Derating:

IP00, Open Type: 0 to 50° C (32 to 122° F) 0 to 50° C (32 to 122° F) Based on drive rating.

IP20, NEMA Type 1: 0 to 40° C (32 to 104° F) 0 to 40° C (32 to 104° F) Based on drive rating.

IP56, NEMA Type 4X:

— 0 to 40° C (32 to 104° F) Frames 9 & 10: 0 to 40 ° C (32 to 104 ° F) surrounding air.

IP65, NEMA Type 4 0 to 40° C (32 to 104° F) — —

Storage Temperature (all

const.):

–40 to 70° C (–40 to 158° F) -40 to 70° C (-40 to 158° F)

Relative Humidity:

5 to 95% non-condensing 5 to 95% non-condensing

Shock:

15G peak for 11ms duration (±1.0 ms) 10G peak for 11 ms duration (± 1.0 ms)

Vibration:

0.152 mm (0.006 in.) displacement, 1G peak 0.152 mm (0.006 in.) displacement, 1G peak, 5.5 Hz 2 mm (0.0787 in.) displacement, 1G peak EN50178 / EN60068-

2-6

Sound

—FrameFan

Speed

Sound

Level

Note: Sound pressure level is

measured at 2 meters.

Frame Sound

Level

Background

Noise Level

Notes: Sound pressure

level is measured at 1

meter. All devices

measured are 400V

IP21 and in power up

mode.

1 30 CFM 59 dB 9 78 49

2 50 CFM 57 dB 10 77 49

3 120 CFM 61 dB 13 76 46

4 190 CFM 59 dB

5 200 CFM 71 dB

6 300 CFM 72 dB

Atmosphere

— Important: Drive must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust.

If the drive is not going to be installed for a period of time, it must be stored in an area where it will not be exposed to a corrosive

atmosphere.

Electrical AC Input

Voltage Tolerance:

±10% of minimum/maximum

See PowerFlex 700S Input Voltage Range/Tolerance

on page 59 for Full Power and Operating Range

Frequency Tolerance:

48-62 Hz. 47-63 Hz

Input Phases:

Three-phase input provides full rating for all drives.

Single-phase operation provides 50% of rated

current.

Three-phase input provides full rating for all drives. Single-phase operation provides 50% of rated current.

DC Input

Voltage Tolerance

— ±10% of Nominal Bus Voltage (above)

Displacement Power

Factor:

5.5-597 kW (7.5-800 HP): 0.95 0.98 across speed range

Efficiency:

97.5% at rated amps, nominal line volts. 97.5% at rated amps, nominal line volts.

Max. Short Circuit Current

Rating:

≤ 200,000 Amps, 600V, using recommended fuse or

circuit breaker type.

≤ 200,000 Amps, using recommended fuse or circuit breaker type.

Maximum Drive to Motor

Power Ratio

— The drive to motor rating cannot exceed a 2:1 ratio