Manual

Chapter 5
Programming Parameters
5–42
Powerup/Diagnostic Fault Status
[PwrUp Flt Status]
Parameter Number 80
Parameter Type Source
Display Units Bits
Drive Units None
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Enums:
This word parameter indicates a fault
condition which has been detected during
power up or reset of the drive. When a bit
is “1”, the condition is true, otherwise the
condition is false.
Bit Condition
0 CP PROM Failure
1 CP Internal RAM Failure
2 CP External RAM Failure
3 CP Stack RAM Failure
4 VP Dualport RAM Failure detected by CP
5 Not Used
6 Not Used
7 Not Used
8 VP EPROM Failure
Bit Condition
9 VP Internal RAM Failure
10 VP External RAM Failure
11 VP Stack RAM Failure
12 CP Dualport RAM Failure detected by VP
13 AP Dualport Ram Failure detected by VP
14 Base Drive EE Failure
15 Reserved, Leave Zero
CP Configurable Fault Status
[CP Flt Status]
Parameter Number 82
Parameter Type Source
Display Units Bits
Drive Units None
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Enums:
This word parameter indicates conditions
detected by the Current Processor (CP)
that has been configured to report as a
Drive fault condition. Each configuration
bit matches the bit definitions of Parameter
84, 86 and 87. When a bit is “1” the
condition is true, otherwise the condition is
false.
Non–configurable Fault Status
[Ncfg Flt Status]
Parameter Number 81
Parameter Type Source
Display Units Bits
Drive Units None
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Enums:
This word parameter indicates fault condi-
tions in the drive that Cannot be configured
as warnings. When a bit is “1”, the condi-
tion is true, otherwise the condition is false.
Bits 0 – 3 are detected by hardware. Bits
4–15 are detected by software.
Bit Condition
0 DC Bus Overvoltage Trip
1 Transistor Desaturation
2 Ground Fault
3 Instantaneous Overcurrent
4 Adapter Comm Loss detected by CP
5 Master/Slave Cable Loss
Bit Condition
0 Bus Ridethrough Timeout
1 Bus Precharge Timeout
2 Bus Drop (150 volts)
Bit Condition
10 Analog Power Supply Tolerance
11 Autocommisioning or Transistor Diagnostic Failure
12 Inverter Temperature Trip
13 Software Malfunction detected by VP
14 Not Used
15 Reserved, Leave Zero
Bit Condition
3 Bus Undervoltage
4 Bus Drop Cycles > 5
5 Fast Fluxup Current < 50%
Bit Condition
6 Master/Slave Enable Timeout
7 Not Used
8 Handshake Timeout VP
9 Absolute Overspeed
VP Configurable Fault Status
[VP Flt Status]
Parameter Number 83
Parameter Type Source
Display Units Bits
Drive Units None
Factory Default 0000 0000 0000 0000
Minimum Value 0000 0000 0000 0000
Maximum Value 1111 1111 1111 1111
Enums:
This word parameter indicates conditions
detected by the Velocity Processor (VP)
that have been configured to report as fault
conditions. Each configuration bit matches
the definitions of Parameter 85, 88 and 89.
When a bit is “1” the condition is true,
otherwise the condition is false.
Bit Condition
0 Feedback Loss
1 Inverter Overtemp Pending
2 Motor Overtemperature Tripped
3 Motor Overload Pending
4 Motor Overload Trip
Bit Condition
10 Math Limit
11 Dynamic Brake Overtemperature
12 AC Motor Contactor Failure
13 Inverter Overload Pending (IT)
14 Drive to Drive Communication Fault
15 Inverter Overload Trip (IT)
Bit Condition
5 Motor stalled
6 External Fault
7 RMS Fault
8 Not Used
9 Parameter Limit