Quick Start Guide User Manual

Pubblicazione 1336 IMPACT-5.5IT – maggio 1999 9
1336 IMPACT Guida all’avviamento rapido
Nome N. Valore Min/Max Nome N. Valore Min/Max
Motore/Inverter
Selez funzione 212 0/27
Targhetta motore Output funz 1 213 Variabile
HP su targhetta 2 0,2 hp/2000,0 hp Output funz 2 214 0/65535
RPM su targhetta 3 1 giri/min./1500
giri/min.
Input funzione 9 232 -32767/+32767
Amp su targhetta 4 0,1 amps/Calc Input funzione 10 233 -32767/+32767
Volt su targhetta 5 75 volts/575 volts
Rigen/contr bus
Hz su targhetta 6 1,0/250,0 Hz Opz bus/frenagg 13 Selezione bit
Poli motore 7 2/40 poli
Comp. Processo
Fattore servizio 9 1,00/2,00 Uscita compens. 48 -800,0/+800,0%
Dati codificatore Rif. compens. 49 -800,0/+800,0%
Codificatore PPR 8 Calc/2000 ppr Fdbk compens. 50 -800,0/+800,0%
Inverter Selez. Compens. 51 Selezione bit
Frequenza PWM 10 1000 Hz/Da inverter Banda filt comp 52 0,0/240,0 rad/sec
Amp inverter 11 0,1 amps/Da inverter Precaric compens 53 -800,0/+800,0%
Volt inverter 12 75/575 volts Ki compensazione 54 0,000/16,000
Costanti motore Kp compensazione 55 0,000/16,000
Resist. Statore 166 0,00/100,00% Limite inf comp 58 -800,0/+800,0%
Indutt. Dispers. 167 0,00/100,00% Limite sup comp 59 -800,0/+800,0%
Corrente flusso 168 0,00/75,00% Guad usc compen 60 -8,000/+8,000
Guad scorrimento 169 0,0/400,0% Comp vel max ind 61 -6 x /0,0 BMS giri/min.
Poli motore 7 2/40 poli Comp vel max av 62 0,0 giri/min./+6xBMS
giri/min.
Applicazione
Avvio lanciato
Frenaggio flusso Selez Avvio Vel 216 0/2
Opz bus/frenagg 13 Selezione bit Veloc Avvio Vel 217 P40/P41
Manten/frenagg CC
Autoregolazione
Opz bus/frenagg 13 Selezione bit Impost. Autoreg
Corrente fren CC 79 0,0%/Calc Sel autoreg/diag 173 Selezione bit
Tempo frenagg CC 80 0,0/6553,5 sec Config trns diag 172 Selezione bit
Cor mtr 400% Coppia autoreg 164 250%/100,0%
Corrente max mtr 195 0/1 Vel. autoreg 165 0,3 x BMS/BMS
Aum rapido flus Stato autoreg
Opz bus/frenagg 13 Selezione bit Stato autoregol 156 Selezione bit
Liv flusso rapid 78 100,0%/Calc Diag invert 1 174 Selezione bit
Tempo pre-avvio Diag invert 2 175 Selezione bit
Vel pre-avvio 193 -0,1 x / +0,1 x BMS Errori autoreg 176 Selezione bit
Tpo pre-avvio 194 0,0/10,0 sec
Risult autoreg
Funzione Prog Resist. Statore 166 0,00/100,00%
Input funzione 1 198 Variabile Indutt. Dispers 167 0,00/100,00%
Masch/val funz 1 199 Variabile Corrente flusso 168 0,00/75,00%
Sel valut funz 1 200 0/17 Guad scorrim 169 0,0/400%
Input funzione 2 201 Variabile Inerzia totale 157 0,0/655,00 sec
Masch/val funz 2 202 Variabile Banda per vel. 161 0,00/Calc rad/sec
Sel valut funz 2 203 0/17
Input funzione 3 204 Variabile
Masch/val funz 3 205 Variabile
Sel valut funz 3 206 0/17
Input funzione 4 207 Variabile
Input funzione 5 208 Variabile
Input funzione 6 209 Variabile