User Manual V 1-4.XX User guide
Table Of Contents
- Front Cover
- Chapter 1
- Chapter 2
- Chapter 3
- Chapter 4
- Chapter 5
- Chapter 6
- Chapter 7
- Chapter 8
- Chapter 9
- Chapter 10
- Chapter 11
- Chapter 12
- Chapter 13
- Appendix A
- Appendix B
- Appendix C
- Appendix D
- Appendix E
- Appendix F
- Who Should Use this Manual?
- What Is the 1336 IMPACT Drive?
- Purpose of this Manual
- Terms and Abbreviations
- Common Techniques Used in this Manual
- Allen-Bradley Support
- Table of Contents
- Preface
- Chapter 1
- Chapter 2
- Mounting and Wiring Your 1336 IMPACT Drive
- Chapter Objectives
- Before Mounting Your Drive
- Input Fuses and Circuit Breakers
- Mounting Your Drive
- Grounding Your Drive
- Wiring the Power
- Hard Wiring Your I/O
- Connecting Your Gateway
- Installing an Interface Board
- Connecting the Power to the Drive
- Disconnecting the Drive Output
- Starting and Stopping the Motor
- Electrical Interference— EMI/RFI
- Do I Need an RFI Filter?
- Mounting and Wiring Your 1336 IMPACT Drive
- Chapter 3
- Chapter 4
- Chapter 5
- Using the LOption
- Chapter Objectives
- What is the LOption?
- What Functions are Available?
- Setting Up the LOption Board
- Using an Encoder with the LOption Board
- Requirements for the Contact Closure Interface Board (L4)
- Requirements for the 24V AC/DC Interface Board Requirements (L5)
- Requirements for the 115V AC Interface Board (L6)
- Requirements for the Contact Closure Interface Board (L7E)
- Requirements for the 24VAC/DC Interface Board Requirements (L8E)
- Requirements for the 115V AC Interface Board (L9E)
- Using the LOption
- Chapter 6
- Starting Up Your System
- Chapter Objectives
- Before Applying Power to Your Drive
- Applying Power to Your Drive
- Recording Your Drive and Motor Information
- Understanding the Basics of the Human Interface Module (HIM)
- Starting Up Your System
- Running the Quick Motor Tune Procedure
- Configuring the Digital Section
- Configuring the Analog Section
- Understanding Links
- Where Do I Go From Here?
- Starting Up Your System
- Chapter 7
- Chapter 8
- Chapter 9
- Applications
- Chapter Objectives
- Choosing a Motor Feedback Source
- Choosing an Optional Braking/Decelerating Method
- Using DC Hold
- Using Up to 400% Motor Current
- Understanding the Scale and Offset Parameters for Analog I/O
- Using 4 – 20mA Inputs/Outputs
- Using a Remote Pot
- Using MOP
- Using Flying Start
- Speed Profiling Introduction
- Speed Profiling Operation
- Speed Profile Start Up Configuration
- Initial Setup Requirements
- Profile Command & Control
- Using the TB3 Inputs
- Encoder Steps
- Applications
- Chapter 10
- Using the Function Block
- Chapter Objectives
- What is a Function Block?
- Evaluating the Inputs
- Using the Timer Delay Function
- Using the State Machine Function
- Using the Add/Subtract Function
- Using the Maximum/Minimum Function
- Using the Up/Down Counter Function
- Using the Multiply/Divide Function
- Using the Scale Function
- Using the Hysteresis Function
- Using the Band Function
- Using the Logical Add/Subtract Function
- Using the Logical Multiply/Divide Function
- Using the Function Block
- Chapter 11
- Chapter 12
- Troubleshooting
- Chapter Objectives
- Required Equipment
- Fault/Warning Handling
- Viewing the Fault and Warning Queues on the HIM
- What Are the Fault Descriptions?
- Understanding Precharge and Ridethrough Faults
- Understanding the Bus Voltage Tracker
- Understanding the Parameter Limit Faults
- Understanding the Math Limit Faults
- Start Up Troubleshooting Procedures
- Miscellaneous Troubleshooting Procedures
- Encoderless Troubleshooting Problems
- Troubleshooting
- Chapter 13
- Appendix A
- Appendix B
- Appendix C
- Appendix D
- Appendix E
- Appendix F
- Index
- Back Cover
11-70 Parameters
217
Fstart Speed
1
Use Fstart Speed to set the start point at which the speed search
begins. This parameter is only active when operating in Fstart
Select mode 2 (Speed Param).
To maximize reconnect performance, always set the Fstart
Speed slightly greater than the expected reconnect motor speed.
1 Fstart Speed was added in Version 3.xx.
Parameter number 217
File:group Application: Flying Start
Parameter type linkable destination
Display x.x RPM
Factory default + base motor speed rpm
Minimum value Rev Speed Limit (Param 40)
Maximum value Forward Speed Limit (Param 41)
Conversion +4096 = base motor speed
Refer to Chapter 9, Applications, for more information.
218 Reserved
Leave this parameter set to 0.
Parameter number 218
File:group
Parameter type
Display
Factory default
Minimum value
Maximum value
Conversion
219
PwrUp Flt Status
1
PwrUp Flt Status indicates that a fault condition has been
detected during power up or reset of the drive. When a bit is “1”,
the condition is true; otherwise, the condition is false.
1 PwrUp Flt Status was added in Version 3.xx.
Parameter number 219
File:group Monitor: Fault Status
Parameter type source
Display Bits
Factory default 0000 0000 0000 0000
Minimum value 0000 0000 0000 0000
Maximum value 1111 1111 1111 1111
Conversion 1 = 1
Bit Condition
0 CP EPROM
1 CP Int RAM
2 CP Ext RAM
3 CP Stack Ram
4 CP MBI
5 Reserved
Bit Condition
6 Reserved
7 Reserved
8 VP EPROM
9 VP Int Ram
10 VP Ext Ram
11 VP Stack RAM
Bit Condition
12 VP MBI
13 Reserved
14 EE Checksum
15 EE R/W
220
Ncfg Flt Status
1
Ncfg Flt Status indicates that a fault condition in the drive
CANNOT be configured as a warning. When a bit is “1”, the
condition is true; otherwise, the condition is false. Bits 0 – 3 are
detected by hardware. Bits 4 – 15 are detected are detected by
software.
1 Ncfg Flt Status was added in Version 3.xx.
Parameter number 220
File:group Monitor: Fault Status
Parameter type source
Display Bits
Factory default 0000 0000 0000 0000
Minimum value 0000 0000 0000 0000
Maximum value 1111 1111 1111 1111
Conversion 1 = 1
Bit Condition
0 Bus Overvolt
1 Trans Desat
2 Ground Flt
3 IOC
4 VP Handshake
5 Diff SW Ver
Bit Condition
6 Dr Type Dif
7 III Drv Type
8 CP Handshake
9 Abs overspd
10 +/- 15v Tol
11 Auto/Diag
Bit Condition
12 Inv Temp Trp
13 Task Overrun
14 Ill Interrupt
15 Mode Timeout