Owner manual

2 DC Motors
General Description The products described in this publication are designed specifically
for use on rectified power. The basic design includes Class F
Insulation, 1.0 Service Factor, 40 degree C (104 degree F) ambient,
continuous duty, with enclosure, horsepower and speed ratings,
overload and voltage in accordance with NEMA Standards. A wide
variety of modifications, enclosures and accessories is available.
Table of Contents Receiving and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installation
Location and Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Conduit Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Shipping Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Motor Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Operation
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Series Wound Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Motor Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
DC Motor Field Heating . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Checking Relative Polarity of DC Motor Fields . . . . . . . . .
15
Maintenance
Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Repacking Bearings or Greasing New Bearings . . . . . . . .
18
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Commutator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
Commutation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Windings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Filters - Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Disassembly and Reassembly Instructions
Air Gap And Shimming . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Axial Float . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Anti-Friction Bearing Assemblies . . . . . . . . . . . . . . . . . . . .
23
Bearing Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Conduit Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Brush Rigging and Brush Holders . . . . . . . . . . . . . . . . . . .
24
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
!
ATTENTION: Only qualified electrical personnel familiar
with the construction and operation of this equipment and
the hazards involved should install, adjust, operate, and/or
service this motor. Read and understand this manual in its
entirety before proceeding. Failure to observe this
precaution could result in personal injury or loss of life.