Reference Guide Owner manual

ManualsBrandsRockwell Automation ManualsEquipment1305 FRN. 6.XX

Quick Reference

1305 Adjustable Frequency AC Drive

Firmware Revision Number 6.01 and Later

This publication is designed as a reference tool. The 1305 User Manual,

publication 1305-5.2, must be consulted for more detailed information about

parameters, faults and hazards of personal injury.

Summary of content (8 pages)

PAGE 1
Quick Reference 1305 Adjustable Frequency AC Drive Firmware Revision Number 6.01 and Later This publication is designed as a reference tool. The 1305 User Manual, publication 1305-5.2, must be consulted for more detailed information about parameters, faults and hazards of personal injury.
PAGE 2
1305 Adjustable Frequency AC Drive Power Terminal Block TB1 Designations GRD GRD L1 R L2 S L3 T BRK ➀ (–DC) T1 U T2 V T3 W Dynamic Brake Option To Motor ➃ Required Input Fusing +DC To Motor ➂ Required Branch Circuit Disconnect AC Input Line ➁ ➀ Connection for Dynamic Brake Resistors for all models except the 200-230 Volt, 0.37 to 0.75 kW (0.5 to 1 HP) drive. Important: The [DB Enable]parameter must be enabled for proper operation.
PAGE 3
1305 Adjustable Frequency AC Drive Terminal Block TB2 Designations General Three Wire General Run Fwd/Rev Remote Pot Remote Pot ➄ ➀ Source 1 Source 2 Wiper or 0-10V DC Input 2 Wiper or 0-10V DC Input 3 Common 3 Common 4 4-20mA Input 4 4-20mA Input 5 0-10V Output 5 0-10V Output 6 Start ➂ 6 Start ➂ 7 Common 7 Common 8 Stop ➂ 8 Stop ➂ User Side 9 ➀➃ 11 Enable ➂ 12 Common 13 Reverse ➂ Jumper ➀➁ 9 Output #1 10 Jumper ➀➃ Run Reverse 11 Enable ➂ 12 Common 13
PAGE 4
1305 Adjustable Frequency AC Drive Faults Name Diag C Lim Fault (F36) Drive -> HIM Drive Reset Fault (F22) EEprom Fault (F32) Hz Err Fault (F29) Hz Sel Fault (F30) HIM -> Drive IPM Current Fault (F44) IPM Overtemp Fault (F45) Max Retries Fault (F33) Motor Mode Flt (F24) Motor Stall Fault (F6) Neg Slope Fault (F35) Network Error Op Error Fault (F11) Open Pot Fault (F9) Overcurrent Fault (F12) Overload fault (F7) Overspeed Fault (F25) Overtemp Fault (F8) Overvolt Fault (F5) Phase U Fault (F38) Phase V Faul
PAGE 5
1305 Adjustable Frequency AC Drive HIM Display Panel Descriptions HIM Control Panel Descriptions Item Item Name Description Escape When pressed, the ESCape key will cause the programming system to go back one level in the menu structure. Select Pressing the SELect key alternately moves the cursor to the next active area. A flashing first character indicates which line is active.
PAGE 6
1305 Adjustable Frequency AC Drive Item Name Description Speed Indicator LEDs (only available with digital speed control) Illuminates in steps to give an approximate visual indication of the commanded speed. If the Analog Speed Potentiometer option has been ordered, the Increment/Decrement keys and Speed Indicator LEDs will be replaced by the pot. 1305 Series C Parameter List Group/ Parameter No. Units Min. Value Max. Value Default Value Group/ Parameter No. Units Min. Value Max.
PAGE 7
1305 Adjustable Frequency AC Drive Group/ Parameter No. Units Min. Value Max.
PAGE 8
Programming System OPERATOR LEVEL Power-Up & Status Display or or or or "Choose Mode" MODE LEVEL Display Process (Read Only) Process Display Program ➀ (Read/Write) EEPROM ➀ Reset Defaults Recall Values Save Values Upload Parameters ➂ Download Parameters ➂ Search ➁ (Read Only) Control Status ➁ Password Control Logic ➀, Fault Queue Login, Logout Modify GROUP LEVEL Parameter Groups (See Parameter List) PARAMETER LEVEL Parameters (See Parameter List) ➀ ➁ ➂ Access to the Program and EEPROM