Owner's Manual

SETTINGS
BALANCE >
AUDIO >
VOLTAGE GAUGE 11V
BT DEVICE PAIRING >
Source Unit Settings
To access the source unit's settings, long press the MENU button until
the options appear. Rotate the encoder to scroll through the list of
settings and short press the encoder button to select the setting you
wish to change . (BALANCE>FADER>AUDIO>VOLTAGE GAUGE>BT
PAIRING>BEEP>TUNER REGION>SOFTWARE>FACTORY DEFAULD
This source unit has a zero current draw when turned off. All of your
settings and presets will be saved along with your boat's battery during
storage.
BALANCE
Short press the encoder button to access BALANCE adjustment settings.
Rotate the encoder button to set output BALANCE.
FADER
Short press the encoder button to access FADER adjustment settings .
Rotate the encoder button to set output FADER.
AUDIO
To access the AUDIO settings, short press the AUDIO option from
the MENU screen. Rotate the encoder to scroll through the list of
settings and short press the encoder button to select the setting you
wish to change. (7 BAND EO>CROSSOVER>PEQ>REAR RCA>AUX
INPUT>SOURCE GAIN>INTERNAL AMPLIFIER)
7BANDEQ
Short press the encoder button to access the 7 BAND EQ settings. Use
the rotary encoder to scroll through the EO settings. (FLAT> ROCK
> CLASSIC > ACOUSTIC > DANCE> ELECTRONIC > HIP-HOP>
CUSTOM) When setting up the CUSTOM EO, short press the encoder
button to set the first frequency. Once active, rotate the encoder to adjust
the frequency settings . Short press encoder button again to access the
next frequency. Repeat until all EQ settings are complete. Short press the
MENU button to exit and go back up one level.
CROSSOVER
Short press to access the CROSSOVER settings. Use the rotary
encoder to select the crossover zone options {FRONT>REAR>SUB).
Short press the encoder to adjust the frequency of the crossover
(60HZ>80H2> 120H2>APF) . Short press MENU to exit and go back up
one level.
REAR RCA
Short press to access the REAR RCA options . Use the rotary encoder to
select options {LINE OUT>SUBWOOFER).
PUNCHEQ
Short press to access the PUNCH EQ settings. Use the rotary encoder
to adjust the gain output (0-12) . Short press MENU to exit and go back
up one level.
~
Punch EQ is an onboard equalizer with up to + 18dB @ 45Hz and/or up to
+ 12dB boost at 12.5kHz
'
Settings
AUX INPUT
RENAME- To rename AUX, short press the encoder button to set the first
letter of the new name . Once active, rotate encoder to adjust letters. Short
press the encoder button again to set the next letter . Repeat until AUX has
been renamed. Short press MENU to exit and go back up one level.
ENABLE - Short press the encoder button to access options. Rotate the
encoder button to select if unit is discoverable. (ENABLE> DISABLE)
SOURCE GAIN
To adjust the level of device input gain. scroll through the inputs (FM
TUNER>AM TUNER>WB TUNER>USB>AUX>BLUETOOTH>PANDORA)
to the device you want to adjust, short press the encoder button to access
the gain settings. Rotate the encoder button to set the level of gain . {-3dB
> -2dB >-1dB > OdB > + 1dB > +2dB > +3dB)
INTERNAL AMPLIFIER
Short press lo access the INTERNAL AMPLIFIER options . Use the rotary
encoder to select options (ON>OFF). When using an amplifier to power
your speakers. select OFF. If you are powering your speakers directly
from the source unit, select the INTERNAL AMPLIFIER to ON.
VOLTAGE GAUGE
To display the vehicle voltage, short press the encoder button on the
VOLTAGE GAUGE option.
BT DEVICE PAIRING
Short press the encoder button to access options (DISCOVERABLE >
DEVICE).
DISCOVERABLE
Rotate the encoder button to select if unit is discoverable for pairing.
(ENABLE> DISABLE) Once enabled, the source unit is now discoverable
and ready for pairing to your device . Open the Bluetooth settings on your
device to find the source unit labeled "Rockford PMX" and select.
DEVICE
Selecting DEVICE by short pressing the encoder button will allow you
to rename the source unit with up to 16 characters. This gives you
the ability to have a unique name for easy identification during device
pairing. Short press the encoder button to select the letter to be changed
and rotate the knob to change the value. Repeat process until desired
name is reached.
BEEP
Short press the encoder button to access the BEEP options. Rotate the
encoder button to turn system beep ON/ OFF.
TUNER REGION
To adjust. short press the encoder button to access . Rotate the encoder
button to select the TUNER REGION of your preference. (EUROPE> USA
>RUSS IA > LATIN> ASIA> JAPAN> MIDEAST> AUSTRALIA)
SOFTWARE
VERSION - Short press the encoder button to display the current
firmware version of the unit.
UPDATE - Short press the encoder button to update the firmware. Follow
the instructions on the screen when updating.
THEME
To adjust the THEME, short press the encoder to access the feature. Rotate
the encoder button to select the desired THEME (DAY, NIGHT, AUTO)
FACTORY DEFAULT
AUDIO - Short press the encoder button to access. Rotate the encoder
button to select YES/NO . Selecting YES will reset your unit back to