RZR ® DASH KIT FOR PMX COMPACT DIGITAL MEDIA RECEIVER RFRZ-PMX2DK Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications 7.7” (96mm) 2.1” (54mm) 5.7” (146mm) FRONT VIEW SIDE VIEW Fig. 1 Mounting Screw Source Unit (Not Included) Existing storage pocket (Not Included) Spring Clip Panel Knockout Dash Kit Shoulder Head Bolt Fig.
Installation Contents • Dash Kit • (4) Mounting Screws • Allen Wrench • Installaton Guide 2014 and up RZR® XP/XP4 1000 2016 and up RZR® XP/XP4 Turbo *2015 and up RZR® XP/XP4 900 * Must purchase storage pocket from Polaris® for a 2014 and up RZR® XP/XP4 1000 to utilize this dash kit on 2015 and up RZR® XP/XP4 900 models.
Installation Lift off the panel once the bolts are removed. This will give you access to the center pocket support bracket. Step 5 - Remove the Center Pocket Protective Cover Turn the center pocket upside down to provide access to the protective cover pins. Using a pry tool, simply pry the two pins loose so you can remove the cover. Step 3 - Remove the Center Pocket Brace Using a Torx screwdriver, remove the bolt that attaches the brace to the rear of the pocket.
Installation Step 6a - Optional Knockout Panels for Accessory Switches Step 7 - Mount the Source Unit to the Dash Kit Before mounting the source unit to the dash kit, make sure that trim bezel that is included with the source unit is NOT attached. If it is attached, you will need to remove it. It will NOT be used. This dash kit also offers additional space to mount up to two rocker panel switches for accessories.
Installation Step 8 - Attach the Dash Kit to the Center Pocket On the rear of the pocket, you will need to remove one of the circular knockout panels providing an access hole to route wiring from your source to your vehicle. Step 9 - Attach the Dash Kit to the Center Pocket NOTE: Make sure the speed clips are lined up correctly or the screw will not be able to be tightened. Step 10 - Reinstalling the Dash Kit Slide the dash kit, source unit and wiring back into the dash.
Installation Step 11 - Reinstalling Instrument Panel Place the instrument panel back on top of the dash. Secure the panel with factory screws. Step 12 - Attach Hood Place the hood back on the vehicle and rotate the mounting clip to the lock the hood back into place.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 120315 1230-60386-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
DIGITAL MEDIA RECEIVER PMX-2
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications Model Operating Voltage Fuse Rating Power Output Max. RCA Output Voltage Output Impedance PMX-2 10.5V - 16V 20A 25 W X 4 @ 4 Ohms RMS 50 W x 4 @ 2 Ohms Peak 4V 500Ω Frequency Response 20 - 20kHz FM Frequency Range 87.5MHz - 107.9MHz AM Frequency Range 530kHz - 1710kHz WB Frequency Range 162.40 - 162.55 (US & Canada) Tuner Presets Clock Display Bluetooth 18 FM / 12 AM / 6 WB No Clock 2.7” Color TFT 3.0+EDR, A2DP 1.3 USB Compatibility 2.
Design Features Rotary Encoder This knob is for adjusting main volume, zone volumes, menu navigation and setting adjustments. REV / FWD button Use this button to skip back and forward through channels or tracks with a short press. Long pressing will activate manual seek mode. MENU button This button gives you access to the main settings of the unit by long pressing. Short pressing will give you access to the settings for the active source.
Wiring Diagram BLACK USB BLACK BLACK RED (REAR LINE OUT RIGHT OR SUB-W OUT) WHITE (REAR LINE OUT LEFT OR SUB-W OUT) GREY RED (FRONT LINE OUT RIGHT) WHITE (FRONT LINE OUT LEFT) RED RED (AUX IN RIGHT) WHITE (AUX IN LEFT) FILTER & FUSE BOX IN 20A FUSE RADIO ANTENNA OUT BLACK WIRED REMOTE 13DIN FEMALE B B ORIENTATION PIN NO.
Installation / Mounting Contents Mounting (Using Mounting Plate) • Source Unit • Screws • Trim Bezel • Power / Speaker Harness • Mounting Plate • Installation & Operation Manual • U Bracket Installation Considerations The following is a basic list of tools needed for installation: • Volt/Ohm meter • Hand held drill w/ assorted bits • Wire strippers • Heat shrink tubing • Wire crimpers • Soldering iron • Wire cutters • Solder • #2 Phillips screwdriver • Heat gun • Battery post wrench • 7mm
Settings AUX INPUT RENAME – To rename AUX, short press the encoder button to set the first letter of the new name. Once active, rotate encoder to adjust letters. Short press the encoder button again to set the next letter. Repeat until AUX has been renamed. Short press MENU to exit and go back up one level. ENABLE - Short press the encoder button to access options. Rotate the encoder button to select if unit is discoverable.
Settings ADJUSTING THE SUBWOOFER OUTPUT Press the SUB + or SUB- buttons to adjust the output level (0-20). ADJUSTING THE SCREEN BRIGHTNESS Short press the SCREEN BRIGHTNESS button to adjust the brightness level. There are two brightness levels. SELECTING A SOURCE TO PLAY Short press the SRC button to show the different source options (FM TUNER>AM TUNER>WB TUNER>USB>AUX>BLUETOOTH>PANDORA>SIRIUSXM). Use the rotary encoder or short press the SRC button to scroll through sources.
Operation ADD PRESETS Short press the encoder button on the ADD PRESETS option. You will need to be on both the station you want to add first. Using this feature allows you to save stations to the unit. Once selected, use the rotary encoder to select the PRESET number (1-6) you want the station saved to. REMOVE PRESETS Short press the encoder button on the REMOVE PRESETS option. You will need to be under the PRESET group you want to adjust first (AM1>AM2).
Operation Pandora® This feature allows you to control the Pandora® app from the source unit directly (Android users will have to use Bluetooth only, iOS users can use both USB and Bluetooth). You will need to start the Pandora® app on your device first, then select the Pandora® source option on the source unit. To use the “Thumbs Up” feature, long press the SUB+ button. To use the “Thumbs down” feature, long press the SUB - button. To play or pause a song, short press the PLAY/PAUSE button.
Troubleshooting Symptom Diagnosis Remedy Basic Blown fuse Check fuse of the unit, replace with correct rating. Vehicle’s ignition is off If connected following the instructions, the unit will not operate with ignition off. Voltage applied to Red wire is not between 10.5 & 16 volts or there is no voltage present Check battery, connections and fuses and repair or replace as necessary. If voltage is above +16 volts, have the electrical system inspected by an authorized service center.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years Source Units – 1 Year All other products – 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 061115 1230-59187-01-D Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
RZR ® FRONT SPEAKER ENCLOSURES RFRZ-FSE Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Enclosure Assembly DRIVER SIDE (LEFT) PASSENGER SIDE (RIGHT) TYPICAL ASSEMBLY (Passenger Side Shown) Mounting Screw Speaker (Not Included) Speaker Wire Access Hole Threaded Mounting Stud Mounting Screw Speaker Enclosure Fig.
Installation Contents • (1) Passenger Side Front Speaker Enclosure • (1) Driver Side Front Speaker Enclosure • (2) Foam Tape • (2) Threaded Studs • (4) Mounting Screws w/ Washers • (2) Mounting Bolts w/ Washers • Installation Guide Installation Tools The following is a list of suggested tools needed for installation: • Ratchet • 5/32” Allen Wrench • 15mm Socket • 13mm Socket Installation Considerations This section focuses on some considerations for installing your Polaris® RZR® Front Speaker Pod Enclo
Installation The speaker pods are designed to work with Rockford Fosgate’s RFRZ-PMXWH1 and RFRZ-K4D wire kits. After the front speaker wire is run threw both down tubes, you are ready to start the process of mounting the enclosure. Step 2 - Attach Threaded Stud Once the bolt is removed, install the threaded stud back into the hole where the bolt was removed. This provides a new mounting point for the speaker enclosure.
Installation Step 4 - Mount the Speaker Enclosure Position the enclosure over the threaded stud and plastic bosses. Be sure to line up the holes before inserting mounting screws and tightening. Step 6 - Mount Speaker Into Enclosure Connect the front speaker wires to the speaker by sliding the connectors over the speaker terminals. Be sure to maintain proper polarity when wiring up the speaker. NOTE: There are (2) mounting screws with washers, (1) mounting bolt that hold each speaker enclosure in place.
7
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 010216 1230-60158-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
RZR ® REAR SPEAKER WIRE KIT RFRZ-RSW16 Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Installation Contents • (2) Rear Speaker Wire Harnesses • Plastic Wire Tie Wraps Installation Tools The following is a list of suggested tools needed for installation: • Security Torx (supplied with • Wire Cutters Wake Cans) • Allen Wrench Installation Considerations This section focuses on some considerations for installing your Polaris® RZR® Rear Speaker Wire Harnesses. This manual will illustrate the installation process with a 2016 Polaris RZR XP4 Turbo.
Installation PM-CL2B Bracket (not included in kit) RFRZ-RSW16 Wire Harness Mounting Tab NOTE: Be sure to leave enough slack so you can connect the speaker to the connector. Wake Can Speaker Enclosure (not included in kit) Step 1 - Mount Mini Wake Can Speaker Bracket You will need to assemble the bottom half of the PM-CL2B to the wake can mount first. Once assembled, feed the white 2 pin connector though the mounting tab and lower bracket.
Installation Continue to route the harness down the rear tube through the shock reservoir opening. The wire harness should follow the upper shock mounting tube. Step 4 - Connect to Rear Speaker Harness Be sure that the center console is removed to gain access to the wire harness. NOTE: Be sure the wire harness is wire tied to the top side of this tube, away from moving components and heat. Feed both wires under the access panel and connect to RFRZ-4KD or RFRZ-PMXWH1 rear speaker harness.
6
7
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 010216 1230-60563-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
SPEAKERS Serial Number: RM0652 • RM0652B RM1652 • RM1652B Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications Model RM0652 RM0652B RM1652 RM1652B Nominal Diameter - inch (mm) 6.5 (165) 6.5 (165) 6.5 (165) 6.5 (165) Description 2-Way 2-Way 2-Way 2-Way 4Ω 4Ω 4Ω 4Ω Frequency Response (Hz) 52-20k 52-20k 49-20k 49-20k Voice Coil Diameter - inch (mm) 1.0 (25.4) 1.0 (25.4) 1.0 (25.4) 1.0 (25.4) Power Handling - Watts (RMS/Peak) 50/100 50/100 75/150 75/150 Fs - Free Air Resonance (Hz) 70.0 70.0 64.5 64.5 Qts 1.08 1.08 0.93 0.93 Vas - cu. ft. (Liter) 0.38 (10.
Specifications RM0652/RM0652B 6.8” (172mm) 4.4” (111mm) 5.4” Dia. (138mm) 3.5” (88mm) 45 ° 2.5” (63mm) 5.4” (138mm) RM1652/RM1652B 6.8” (172mm) 4.4” (111mm) 5.4” Dia. (138mm) 3.6” (90mm) 45 ° 2.5” (63mm) 5.4” (138mm) illus.-1.
Installation Contents Example of standard installation • (1) Pair Marine Grade Speakers • (8) Socket head stainless screws RM0652/RM0652B • (1) Socket head driver bit Installation Considerations Before beginning any installation, follow these simple rules: 1. Be sure to carefully read and understand the instructions before attempting to install these speakers. 2. For safety, disconnect the negative lead from the battery prior to beginning the installation. 3.
Français Considérations Concernant L’installation Español Consideraciones para la instalación Avant de commencer l’installation, suivez les règles ci-dessous: Antes de comenzar cualquier instalación, siga estas simples normas: 1. Veillez à bien lire et comprendre les instructions avant d’essayer d’installer les haut-parleurs. 1. 1. Asegúrese de leer cuidadosamente y de entender las instrucciones antes de tratar de instalar estos altavoces. 2.
Deutsch Einbauüberlegungen Befolgen Sie vor dem Einbau diese einfachen Regeln: 1. 1. Lesen Sie die Anleitung sorgfältig, bevor Sie versuchen diese Lautsprecher einzubauen. 2. Entfernen Sie vor dem Einbau aus Sicherheitsgründen das negative Kabel von der Batterie. 3. Um die Montage zu erleichtern, empfehlen wir alle Kabel vor der Befestigung Ihrer Lautsprecher zu verlegen. 4. Verwenden Sie nur Qualitätsstecker, um einen zuverlässigen Einbau zu gewährleisten und Signal- und Stromverlust zu minimieren. 5.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 121514 1230-58876-01 Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
SUBWOOFERS RM18D2 • RM18D2B RM18D4B • RM110D2 RM110D4 • RM110D4B RM112D2B Serial Number: • RM112D4 • • RM18D4 RM110D2B • • RM112D2 RM112D4B Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications RM18D2 / RM18D2B RM18D4 / RM18D4B RM110D2 / RM110D2B RM110D4 / RM110D4B RM112D2 / RM112D2B RM112D4 / RM112D4B Nominal Impedance (Ohms) 2 Ω DVC 4 Ω DVC 2 Ω DVC 4 Ω DVC 2 Ω DVC 4 Ω DVC Frequency Response (Hz) 30-250 31-250 25-250 26-250 21-250 22-250 Voice Coil Diameter - inch (mm) 1.5 (4-Layer) (38.6) 1.5 (4-Layer) (38.6) 2 (4-Layer) (50.8) 2 (4-Layer) (50.8) 2 (4-Layer) (50.8) 2 (4-Layer) (50.8) Displacement - cu. ft. (Liter) 0.05 (1.41) 0.05 (1.41) 0.1 (2.83) 0.
Enclosures Carton Contents • (1) Marine Grade Subwoofer • (1) Socket head driver bit • (1) Grille • Installation and Operation Manual • (8) Socket Head Stainless Screws Recommended Enclosures This manual outlines two specific types of enclosures that provide distinctly different performance. This section is to help you decide which type is best for your application. Sealed Enclosures Sealed enclosures are the simplest to build.
Enclosures Vented Enclosures NOTE: Vb is the internal volume, before any speaker and/or port displacement is added. All external dimensions were based on the use of 3/4” (1.90cm) materials. NOTE: When using enclosures other than recommended, call Technical Support for correct application. Infinite Baffle 8” 10” 12” F3 - 3dB Point (Hz) 42.7 69.4 43.3 Vas - cu. ft. (Liter) 0.63 (17.9) 1.77 (50.2) 3.80 (107.7) Qtc - Enclosure Damping 0.66 0.43 0.
Français Español Enceintes recommandées Ce manuel décrit deux types particuliers d’enceintes aux performances tout à fait distinctes.Cette section vous permettra de décider celui qui vous conviendra le mieux. Enceintes Étanches Les enceintes étanches sont les plus faciles à fabriquer.À cet égard, la chose la plus importante dans leur fabrication est de vous assurer qu’elles sont vraiment hermétiques.
Deutsch Italiano Empfohlene Gehäuse DieseAnleitung beschreibt zwei spezifischeTypen von Gehäusen, die grundsätzlich verschiedene Performancemerkmale bieten.DieserAbschnitt soll Ihnen dabei helfen zu entscheiden,welcher der besteTyp für IhreAnwendung ist. Geschlossene Gehäuse Geschlossene Gehäuse lassen sich am leichtesten bauen.Der wichtigsteAspekt beim Bau eines geschlossenen Gehäuses ist zu gewährleisten, dass es luftdicht ist.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 012115 1230-59130-02 Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
RZR ® FRONT SUBWOOFER ENCLOSURE RFRZ-FWE Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Enclosure Assembly 28.5” (724mm) 12.5” (318mm) 14.7” (374mm) TOP VIEW PASSENGER SIDE (RIGHT) FRONT VIEW DRIVER SIDE (LEFT) TYPICAL ASSEMBLY Mounting Bracket and Bolts Mounting Bracket and Bolts Subwoofer (Not Included) Mounting Bracket and Bolts Subwoofer Enclosure Fig.
Installation Contents • (1) Front Subwoofer Enclosure • (1) Latch Mount & Screws • (3) Enclosure Mounting Brackets • (1) 12 AWG Subwoofer Wire • (1) Subwoofer Spacer Ring • Installation Guide • (1) 12 AWG Jumper Wire Applicable Models: 2014 and up RZR® XP/XP4 1000 2016 and up RZR® XP/XP4 Turbo 2015 and up RZR® S/ XC / 4 900 • (1) Mounting Screw Pack Installation Tools The following is a list of suggested tools needed for installation: • Ratchet • Torx - T40 • 15mm Socket/Wrench • 13mm Sock/Wrench
Installation Using your hands, pull the top dash piece toward the interior of the vehicle to release it from the dash. Disconnect all of the wires connectors and set aside. Step 3 - Remove Passenger Grab Bar To remove the grab bar, you will need remove the retaining pin and pull the grab bar out of it’s mount. Step 4 - Remove Center Pocket Using a Torx screwdriver, remove the bolt that attaches the brace to the rear of the pocket.
Installation Once the bolts are removed you will need to pull the dash off of the chassis. Once the glove box door is removed, remove the bolts holding the glove box in place. There are two above the chassis dash bar. NOTE: When pulling the dash off you will notice that it still feels attached. It has several retaining clips on each side that are holding it in place. Just continue pulling toward the interior of the vehicle to release the dash from the chassis.
Installation Place the subwoofer into the enclosure and line up the predrilled holes in the enclosure with the subwoofer’s mounting holes. NOTE: If you subwoofer mounting holes do not line up, predrilling holes is suggested before screwing subwoofer to enclosure. NOTE: When installing your subwoofer be sure to check for interference with the subwoofer and the inside of the enclosure. A spacer ring is included in the kit if you have a subwoofer that is touching the enclosure.
Installation Step 9 - Replace Center Pocket Bracket The center pocket bracket will need to be removed and replaced with a new bracket that comes with the kit. Step 11 - Install the Loaded Subwoofer Enclosure Once all of the brackets are installed, the subwoofer enclosure can now be installed. The enclosure goes into the vehicle with the subwoofer facing the fire wall and the flat side of the enclosure is on top. The box needs to inserted up towards the driver’s side of the vehicle first.
Installation NOTE: Due to the weight of the enclosure and subwoofer, an additional person to help is recommended. Step 12 - Install Glove Box Door After all of the brackets are tight and secure, the glove box door will need to be installed onto the enclosure. Insert the door stud towards the passenger side retainer first, then insert the stud on the passenger side. NOTE: The glove box latch mount that is pre installed on the enclosure is designed to work with 2015 and newer model latching systems.
Installation Step 13 - Install Dash Now you can install the dash back into place. Step 14 - Install Center Pocket After you have the dash installed, the center pocket can go back in the vehicle. Be sure to slide the pocket support onto the new stud from the enclosure. NOTE: This threaded stud replaces the factory installed center pocket bracket. Step 15 - Install Top Dash, Hood and Grab Bar You can reinstall the top dash panel, hood and grab bars after connecting your subwoofer to an amplifier.
Installation 11
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 010216 1230-60159-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
RZR ® DUAL AMPLIFIER INSTALLATION KIT RFRZ-K4D Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Amplifier Bracket Assembly AMPLIFIER BRACKET TYPICAL ASSEMBLY Amplifier (Not Included) Dual Amplifier Mounting Bracket Fig.
12V Battery 4 Rear Right 4ch AMP Optional RFRZ-RSW16 (Not Included) SUB AMP Rear Left Front Speaker Front RCA Rear/Sub RCA Optional RFRZ-RSW16 (Not Included) Subwoofer REM Front Right Front Left Wire Harness Schematic Switched B+ GND PMX-2 Source Unit Rear Speaker
Installation Contents • (1) Amplifier Mounting Bracket • (3) RCA Harnesses • (1) Main Power / Ground / Rear Speaker Harness w/ Fuse • (2) Foam Tape Pads • (1) Source Unit Power Harness • Plastic Wire Tie Wraps • (1) Front Speaker Harness • Installation Guide • (1) Bolt / Screw Pack Applicable Models: 2014 and up RZR® XP/XP4 1000 2016 and up RZR® XP/XP4 Turbo 2015 and up RZR® S/ XC / 4 900 Installation Tools The following is a list of suggested tools needed for installation: • Ratchet • 5/32” Allen
Installation Using your hands, pull the top dash piece toward the interior of the vehicle to release it from the dash. Disconnect all of the wires connectors and set aside. After the brace is disconnected from the center pocket, pull the pocket out of the dash. Step 4 - Remove Dash Using your Torx screwdriver, remove the two bolts holding the dash onto the chassis. There are two and they are located above the center pocket. Once the bolts are removed you will need to pull the dash off of the chassis.
Installation Step 5 - Remove Center Console After all of the seats have been removed, you will need to remove the center consoles on the vehicle. This is necessary to route the wire harnesses down the vehicle. Next, remove the rear console if equipped (4 seater). NOTE: On the 4 seater that is shown, both the front and rear center consoles will be removed. For 2 seat vehicles, there is only one center console that needs to be removed.
Installation Remove the existing rubber grommet in the fire wall and cut along the score lines to open it up for the wire harness. Place the grommet over the wire harness. Pull the wire harness through to provide enough slack for when mounting the amplifiers. Step 7 - Install Amplifier Bracket You will need to loosen the two nuts that are located above the steering column. These will hold one side of the bracket. Insert the wire harness in through the opening on the fire wall and lock the grommet in place.
Installation Now install the center pocket brace back into the vehicle in between the amplifier bracket and the fire wall support bar. Use the existing factory hardware. Step 9 - Route Source Unit Power Harness Next you will need to route the source unit power harness through the fire wall. Starting on the inside of the vehicle, take the end with the ring terminals and push them through the grommet where the main harness was just run.
Installation NOTE: Depending on the type of source unit being used. You may not use all three RCA cables that are included in the kit. If you are using the recommended PMX-2, you will only need to connect the Front and Sub RCAs to the appropriate amplifiers. Step 10 - Mount Amplifier(s) Set the amplifier on top of the bracket and align it to the left. The bracket is labeled with indicators for the amplifier mounting screws. Simply slide the amplifier over to the left (driver’s side) and line up the holes.
Installation Step 15 - Reassmble Vehicle Once everything is secure, reassemble the vehicle. You will need to leave the top dash panel off so you can adjust the amplfiers. Once the system is tuned, install the top dash panel and hood. Step 13 - Connect to Battery Once you have wire harness secured, connect the power and ground to the battery terminals. NOTE: If you have a 2 seater, the wire harness will need to be bundled up and tie wrapped. Do not cut the harness.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance available at: 122315 1230-60159-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
BOOSTED RAIL MONO AMPLIFIER PBR300X1 Installation & Operation Installation et fonctionnement Instalación y funcionamiento Einbau und Betrieb Installazione e funzionamento
INTRODUCTION Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product.Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
GETTING STARTED Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents.We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current.
DESIGN FEATURES 1. BRT(Boosted Rail Technology) LED – This LED illuminates when the unit is in boost mode. 2. Power/Protect LED – This LED illuminates Blue when the unit is turned on and Red if a short circuit/low impedance is detected at the speaker connections or the amplifier’s internal components become too hot engaging the protection.The amplifier will shut down to cool if this occurs. 3.
INSTALLATION INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Fuse-holder and fuse.
INSTALLATION BATTERY AND CHARGING Amplifiers will put an increased load on the vehicle's battery and charging system.We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Punch Series amplifier without problems, although battery and alternator life can be reduced slightly.
INSTALLATION Power Connection 7. Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops. 8. Connect from source signal by plugging the RCA cables into the RCA/Speaker Harness input jacks, then insert the four pin Molex connector into the mating four pin INPUT connector at the amplifier.
OPERATION REMOTE PUNCH EQ (Option) NOTE:Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers. NOTE: Use the instructions that came with the remote for a variety of mountings that fit your preference. Quick Install 1. Using the screws supplied, install the mounting clip. 2. Slip the remote onto the mounting clip until it snaps into place. 3. Route and connect the cable to the remote and amplifier. Operation 4. Variable bass boost centered at 45Hz.
TROUBLESHOOTING NOTE:If you are having problems after installation follow the Troubleshooting procedures below. Procedure 1: Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 3.
SPECIFICATIONS MODEL- PUNCH PBR300X1 Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts 4 Load Mono 75 Watts x 1 2 Load Mono 150 Watts x 1 1 Load Mono 300 Watts x 1 Dimensions: Height 1.53" (3.90cm) Width 4.25" (10.8cm) Length 6.75" (17.
LIMITED WARRANTY INFORMATION Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Source Units, Speakers, Signal Processors and PUNCH Amplifiers – 1Year POWER Amplifiers – 2Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Rockford Fosgate Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (480) 967-3565 - Customer Service 1-800-669-9899 www.rockfordfosgate.
r-=-: L. e J I I I I PerForlTlance VeriFicat.ion PBR300X1 Model: Serial # : Birth Date: Rated Power: 300 Watts Tested By : JASON BAKER 02/16/2011 Engineering N/A Channel Separation: 0.161 % Rated Power: @ I n s p e c t . i o n Dat.a +14.4V CEA Test Voltage: THD+N Cert.iFicat.e PASS PASS Frequency Response: Speaker Short Protection: PASS PASS Thermal Management: Punch® EQ Circuit: Actual Power 95 X 1 @ 4 Ohms 178 X @ 2 Ohms 308 X @ 1 Ohms PASS Final Inspection: SpeciFicat.
Are You Engineered to Rock, Or Wired for Stock? Get a One Year Extended Warranty when you use matching Rockford Fosgate or Lightning Audio Amplifier Installation kit with this Amplifier! We want you to get the performance and reliability that made Rockford Fosgate Amplifiers Famous. Using poor-quality under-spec wiring is a guaranteed way to get less than you paid for from your system.
B OOS T E D R A IL 4 C HA NNE L A MP L IF IE R PBR300X4 Installation & Operation Installation et fonctionnement Instalación y funcionamiento Einbau und Betrieb Installazione e funzionamento
INTRODUCTION Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
GETTING STARTED Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents. We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current.
DESIGN FEATURES 1. BRT(Boosted Rail Technology) LED – This LED illuminates when the unit is in boost mode. 2. Power/Protect LED – This LED illuminates Blue when the unit is turned on and Red if a short circuit/low impedance is detected at the speaker connections or the amplifier’s internal components become too hot engaging the protection. The amplifier will shut down to cool if this occurs. 3.
INSTALLATION INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Fuse-holder and fuse.
INSTALLATION BATTERY AND CHARGING Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Punch Series amplifier without problems, although battery and alternator life can be reduced slightly.
INSTALLATION Power Connection 7. Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops. 8. Connect from source signal by plugging the RCA cables into the RCA/Speaker Harness input jacks, then insert the four pin Molex connector into the mating four pin INPUT connector at the amplifier.
OPERATION ADJUSTING CROSSOVER Placing the crossover switch in the HP position sets the amplifier to the 80Hz High Pass mode, enabling frequencies above the cut-off point to pass. Placing the crossover switch in the AP position sets the amplifier to the All Pass mode, preventing any crossover adjustment, allowing all frequencies to pass. Placing the crossover switch in the LP position sets the amplifier to the 80Hz Low Pass mode, enabling frequencies below the cut-off point to pass.
TROUBLESHOOTING NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Procedure 1: Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 3.
SPECIFICATIONS MODEL- PUNCH PBR300X4 Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts 4 Load Stereo 75 Watts x 4 Dimensions: Height 1.53" (3.90cm) Width 4.25" (10.8cm) Length 6.75" (17.
LIMITED WARRANTY INFORMATION Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Source Units, Speakers, Signal Processors and PUNCH Amplifiers – 1 Year POWER Amplifiers – 2 Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Rockford Fosgate Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (480) 967-3565 - Customer Service 1-800-669-9899 www.rockfordfosgate.
~,..-----) PerFormance VeriFication Model: PBR300X4 Serial# : Birth Date : CertiFicate Rated Power : 300 Watts Tested By: JASON BAKER 05/18/2011 Engineering Inspection Data CEA Test Voltage: +14.4V Channel Separation: N/A THD+N @ 0.197% Rated Power: PASS Frequency Response: Actual Power 84 X 4 @ 4 Ohms PASS Speaker Short Protection: PASS Thermal Management: PASS Punch® EQ Circuit: PASS Final Inspection: Spec:iFic:ations Crossover Frequency Response .,,, ·•.,., ...
Are You Engineered to Rock, Or Wired for Stock? Get a One Year Extended Warranty when you use matching Rockford Fosgate or Lightning Audio Amplifier Installation kit with this Amplifier! We want you to get the performance and reliability that made Rockford Fosgate Amplifiers Famous. Using poor-quality under-spec wiring is a guaranteed way to get less than you paid for from your system.
ROCKFORD TECHNICAL SUPPORT QUICK SETUP RZR STAGE 3/4 AMPLIFIER SETTINGS Selectable 2/4 Channel Switch must be set to 2 CH for this application. Variable FRONT gain setting need to be at 9 for this application. Variable CROSSOVER FREQ. setting needs to be positioned toward the “z” in Hz for this application. Variable GAIN setting needs to be positioned toward the “7” in this application. Variable REAR gain setting need to be at 9 for this application.
