998 - 2013 HARLEY-DAVIDSON® AMPLIFIER INSTALL KIT RFKHD9813 Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications 8.4” (213mm) Note: This mounting plate is specifically designed for Rockford Fosgate’s compact chassis amplifiers. Compatible models are PBR300X2, PBR300X4, T400X2ad, T400X4ad, TM400X2ad and TM400X4ad. 5.2” (133mm) TOP VIEW 8.4” (213mm) 5.2” (133mm) BOTTOM VIEW 1.1” (30mm) SIDE VIEW illus.-1.
Design Features Amplifier Mounting Plate This amplifier mounting plate is specifically designed to work with Rockford Fosgate’s POWER and PUNCH® compact chassis amplifiers in both 2 and 4-channel configurations. Bracket (Type 1) This bracket is used on Road Glide® and Road Glide Ultra® motorcycle fairing styles only. It mounts to the clutch side turn signal bracket. Bracket (Type 2) The bracket is to be used on Ultra Classic®, Electra Glide®, Street Glide® and Tri Glide® motorcycle fairings only.
Design Features Power / Ground Harness Preterminated 8 AWG Power and Ground Harness with inline Maxifuse. Connects directly into amplifier and to motorcycle battery with terminated ends. Front Speaker Input Harness Preterminated harness connects to factory front speaker wire harness and amplifier front input socket. Front Speaker Output Harness Preterminated harness connects to front speakers and amplifier front output socket.
Wiring Diagram FRONT Front Speaker Front Speaker (Connect to factory speaker wire) (Connect to factory speaker wire) Front Speaker Input Harness Front Speaker Front Speaker (Connect to speaker) (Connect to speaker) Front Speaker Output Harness Clutch Side Brake Side Rear Speaker Input Harness Rear Speaker Power Harness Speaker Input / Output Harness (Rear) Output Harness NOTE: This wiring diagram is for a standard 4-Channel amplifier installation.
Installation Contents • Extruded Heat Sink Mounting Plate • Power/Ground Wire Harness w/ Inline Maxifuse • Road Glide® Fairing Style Bracket • Front Input Harness • Street Glide® Fairing Style Bracket • Rear Input/Output Harness Ultra Classic®, Electra Glide®, Street Glide® and Tri Glide® models.
Installation You will need to disconnect the harness from the headlight to completely take the fairing off of the motorcycle. Step 3 - Amplifier Mounting Mount amplifier upside down (as pictured) with the supplied screws to the mounting plate. Align the amplifier to the appropriate holes on the plate. They are labeled for either a PUNCH® or POWER compact chassis amplifier in 2 and 4 channel configurations.
Installation Example below: 4-Channel Power Amplifer Note: Refer to your amplifier’s owner manual for additional wiring and setup information. Be careful when plugging in the harnesses to the appropriate socket. The 4-pin Molex plugs for the Input / Output Harnesses fit in both sides of the amplifier. Step 1 - Removal Leaving the windshield in place, remove the six inner fairing screws.
Installation Pull the fairing toward the front of the bike and up to release it from the fairing mounts. Unplug headlight harness and set fairing aside. Step 3 - Amplifier Mounting Mount amplifier upside down (as pictured) with the supplied screws to the mounting plate. Align the amplifier to the appropriate holes on the plate. They are labeled for either a PUNCH® or POWER compact chassis amplifier in 2 and 4 channel configurations.
Installation Example below: 4-Channel Power Amplifer (4-Channel Amplifier) Step 6 - Rear Speaker Installation With the seat already removed, route the Rear Speaker Harness toward the rear of the motorcycle over the fender along the brake side of the motorcycle. Note: Refer to your amplifier owner’s manual for additional wiring and setup information. Be careful when plugging in the harnesses to the appropriate socket. The 4-pin Molex plugs for the Input / Output Harnesses fit in both sides of the amplifier.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years All other products - 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance availible at: www.rockfordfosgate.com/rftech 120814 1230-59479-01 Printed in China 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
