RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 1 Thursday, April 14, 2016 3:08 PM 19” to 39” TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications ......................2 Tools needed......................................................................2 Package contents .............................................................3 Installation instructions .................................................
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 2 Thursday, April 14, 2016 3:08 PM Safety information and specifications IMPORTANT Maximum TV weight: 35 lbs. (15.8 kg) SAFETY INSTRUCTIONS Screen size: 19" to 39" diagonal - SAVE THESE Overall dimensions (H × W × D): INSTRUCTIONS 8.8 x 8.8 x 3.2 in. (224.7 x 223.6 x 80.3 mm) CAUTION: Do not use this product for any purpose not Wall-mount weight: 3.2 lbs. (1.45 kg) explicitly specified by We’re here for you Rocketfish. www.rocketfishproducts.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 3 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount: 2 TV bracket extender (4) 1 TV Bracket (1) 3 TV bracket extender screws (8) 18 7/32 Hex Key (1) 14 Wall plate assembly (1) 13 Template (1) Need help? Call 1-800-620-2790 (U.S.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 4 Thursday, April 14, 2016 3:08 PM TV Hardware Lbl Hardware Qty. Lbl M4 × 12 mm screw 4 4 5 M6 × 12 mm screw 4 6 M8 × 20 mm screw 4 M4 × 35 mm screw 7 M4 washers 10 4 11 M6/M8 washers 4 12 Universal spacers 4 15 2 5/16" × 2 3/4" lag bolt 4 8-32 × 3/8-in. locking screw 16 9 Qty.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 5 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB Installation instructions STEP 1 - Measure your TV hole pattern and assemble the TV bracket 1 Measure the width and height of your TV hole pattern in centimeters to determine which TV bracket configuration fits your TV. W es inch H cm 2 3 Record your measurements in cm: Width ______cm x Height ______cm. inches cm mm 3 7.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 6 Thursday, April 14, 2016 3:08 PM Configuration A - TV bracket only Select the holes that conform to your TV configuration. 10 cm 7.5 cm 7.5 cm 10 cm 20 cm 20 cm Configuration B - TV bracket (1) with bracket extenders (2). Assemble the TV bracket as shown, with eight screws (3). 20 cm 10 cm Configuration C - TV bracket (1) with bracket extenders (2). Assemble the TV bracket as shown, with eight screws (3). 6 Need help? Call 1-800-620-2790 (U.S.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 7 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB Step 2 - Determine whether your TV has a flat back or an irregular or obstructed back 1 2 3 4 5 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions. Temporarily lay the TV bracket (1) on the back of your TV.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 8 Thursday, April 14, 2016 3:08 PM STEP 3 - Select screws, washers, and spacers 1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV requires, test various sizes by hand threading the screws.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 9 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back 1 2 3 Align the holes you noted on the TV bracket (1) with the screw holes on the back of your TV. Make sure the bracket is level. Place the washers (10 or 11) over the holes in the TV brackets that align with the screw holes on the back of your TV, then insert the screws (4, 5, or 6) through the washers.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 10 Thursday, April 14, 2016 3:08 PM STEP 4 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs 1 2 3 Place the spacers (12) over the screw holes on the back of the TV. Align the TV bracket (1) over the spacers (12), then place the washers (10 or 11) over the holes in the TV bracket and insert the screws (7, 8, or 9) through the washers, TV bracket, and spacers. Make sure the bracket is level.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 11 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB STEP 5 - Determine wall-mount location • • NOTE: For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the ground.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 12 Thursday, April 14, 2016 3:08 PM STEP 6 - Option 1: Installing on a wood stud wall 1 2 3 Note: Drywall covering the wall must not exceed 5/8" (16 mm). Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. Align the center of the wall plate template (13) at the height you determined in the previous step and make sure that it is level.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 13 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB NOTE: If needed, you can make small level adjustments to the wall plate by loosening the bottom lag bolt and shifting the wall plate until it is level. Tighten the bottom lag bolt when the adjustments are complete. You’ll need Lag bolt 15 (2) Level Pencil Edge-to edge stud finder 7/32" wood drill bit Wall plate assembly (14) Tape Template (13) Drill 1/2" socket wrench Need help? Call 1-800-620-2790 (U.S.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 14 Thursday, April 14, 2016 3:08 PM STEP 6 - Option 2: Installing on a solid concrete or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount wall plate directly onto the concrete surface. Note: Minimum solid concrete thickness: 8 in (203 mm). Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm).
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 15 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB 6 Replace the cover caps. Cover cap Cover cap C1 C1 Cover cap Cover cap C1 NOTE: If needed, you can make small level adjustments to the wall plate by loosening the bottom lag bolt and shifting the wall plate until it is level. Tighten the bottom lag bolt when the adjustments are complete.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 16 Thursday, April 14, 2016 3:08 PM STEP 7 - Attach your TV to the wall plate 1 2 3 To make it easier to attach your TV to the wall plate, position the arm of the wall plate assembly (14) so the elbow is bent 90 degrees and pressed against the wall. Hang the TV onto the arm of the wall plate assembly (14) by first hooking the top support, then lowering the bottom of the TV into place. Lock the TV to the wall plate assembly (14) with locking screw (16) and washer (17).
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 17 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB STEP 8 - Managing cables • Thread your cables into the channels on the arms of the wall plate assembly (14) as shown below. IMPORTANT: Be sure to pull the TV away from the wall to fully extend the arms so that you provide enough slack in the cables during operation. Need help? Call 1-800-620-2790 (U.S.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 18 Thursday, April 14, 2016 3:08 PM STEP 9 - Making adjustments 1 Your TV should tilt easily when moved, then stay in place. If your TV is too loose or too tight, adjust the tilt tension knob by hand. NOTE: Once your TV is in place, tighten the tilt tension knob to prevent unwanted movement. Tilt adjustment Tighten Tilt tension knob Loosen 2 To level your TV, loosen the locking screw (16), level your TV, then tighten the screw.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 19 Thursday, April 14, 2016 3:08 PM RF-HTVMMAB 3 Your TV should swivel easily, then stay in place. If your TV is too loose or too tight, adjust the arm tension screw using the hex key (18) and a 14 mm (9/16 in.) socket. Swivel adjustment Tighten Arm tension screw Loosen 9/16 in (14 mm) socket 4 Your TV’s arm should extend and retract easily, and stay in place when moved. If your TV is too loose or too tight, adjust the arm tension screws using the hex key (18).
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 20 Thursday, April 14, 2016 3:08 PM Removing the TV from the wall mount • To remove your TV from the wall plate assembly (14), disconnect all cables, then reverse the procedures in Step 6. IMPORTANT: Your TV is heavy. You may need assistance with this step. For customer service, call: 1-800-620-2790 (U.S. and Canada) 20 Need help? Call 1-800-620-2790 (U.S.
RF-HTVMMAB_16-0210_MAN_V1_ENG.fm Page 24 Thursday, April 14, 2016 3:08 PM Part # 6907-002111 00 www.rocketfishproducts.com (800) 620-2790 (U.S. and Canada) ROCKETFISH is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2016 Best Buy. All rights reserved.
