Ford Raptor Step Slider Installation SS-F150-4DR Installation Instruction RSEI 119
PARTS LIST 1 DESCRIPTION Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol Pad 1 Cut Off Switch 1 Anti-Seize Packet 1 Control Box 2 Top Brackets 2 Back brackets 2 Grip Tape Strips 4 Door Sensors 4 Actuating Magnets 24 7/16” Washers 24 Aluminum Nutserts 14 5/16” SS Button Head Bolts 14 5/16” Stainless Steel Washers *Optional: 2 LED Light Strips *If any parts listed are missing or damaged please ca
STEP SLIDER INSTALLATION 1. Remove the stock rocker panel guards 2. The top bracket will be installed first (If the brackets are not symmetrical make sure you install the correct bracket on the correct side) 3. The bracket start point is approximately 4 3/8 inches back from the front door seam. 4. Find your starting point and hold the bracket up against the truck. Hold the bracket up against the truck panel matching the body angles.
6. From the center of the pilot hole, step up the hole size using a ½” bit to create a finish hole that will be used to install the nutserts 7. Install nutserts in the holes that were just drilled into the body of the truck a. We suggest using a crimping tool to optimize the integrity of the nutserts to support the slider b. If no crimping tool is available, follow these instructions i. Install by using a 5/16’’x1.125’’ minimum length bolt with a 3/8’’ nut ii.
10. Place step slider in place and put two countersunk bolts in the matching holes to hold the slider in place. BE SURE TO TIGHTEN THESE BOLTS. DO NOT OPEN THE DOOR WITH THESE PARTICALLY INSTALLED IT WILL SCREWUP YOUR DOOR. a. Make sure you put included anti-seize on bolt, since it is stainless steel and when stainless steel is bolted into steel it can be hard to remove 11. Attach the back bracket to step slider body with two or three bolts and position it in place as to where to secure it to the truck.
18. Attach the slider to the top bracket using the stainless steel bolts. Don’t forget to use the anti-sieze on each stainless steel bolt 19. Tighten the bolts from the back bracket to the step slider body 20. These holes are elongated to allow for any adjustments that need to me made. 21. When the slider is mounted make sure that you have not twisted or manipulated the shape of the slider with you tightening sequence. THIS WILL CAUSE THE STEP TO NOT WORK PROPERLY. 22.
Step Slider Wiring Diagram Driver Side Front Door Sensor Rear Door Sensor Driver LED Light Driver Actuator Wire Color Orange/Yellow Orange/Pink Brown/Tan Red/Black Passenger Side Front Door Sensor Door Sensor Passenger LED Light Passenger Actuator Wire Color Green/Gray Blue/White Pink/Tan Red/Black **WARNING** REMOVE FUSE FROM WIRING HARNESS PRIOR TO INSTALLATION! CONNECTING THE HARNESS TO THE POWER SOURCE WITH THE FUSE ATTACHED MAY SHORT OUT THE WIRING HARNESS.
4. Position the control box under the rear seat or near the back of the cab, anywhere out of the way where the wiring harness will fit to both sides of the truck. a. Choose a location out of sight and in a secure spot so it will not come into contact with anything or be kicked by a rear seat passenger 5. Plug the harness into the control box and lay the harness wire into position in the truck starting on the rear passenger side a.
10. Returning to the backseat, complete the driver’s side. Run the actuator wires from the step slider through the floor of the vehicle and plug into the wiring harness. Plug into the red/black connector into the wiring harness. a. Secure wires to minimize slack so they are protected. We recommend zip ties b. *Optional: The brown/tan wire is used if LED light package is being installed 11.
17. Route these wires along the firewall up to the battery compartment a. Secure the wires using the harness attached to the firewall 18. Attach the NEG- to the NEG- side of the battery 19. Attach the POS+ to the POS+ side of the battery 20. Position the actuating magnets on the catch side of each door a. Make sure the actuating magnets are in perfect line with the sensors b. **DO NOT allow the magnet and sensor to come into direct contact.
c. Once that proper placement is achieved we recommend using a permanent marker to outline the magnet on the door. 21. Re-check all wires to make sure they are completely secure and free from coming into contact with any moving part to prevent system damage due to a cut wire 22. Reinstall all internal plastic and carpet pieces that were removed. 23. Make sure that all wires are tucked back and out of heavy traffic areas on the floor. a. Route them toward the furthest back area underneath the rear seat 24.
and study the way the slider operates. Look at the slider for wear in the powder coating. The slider leaves our manufacturing facility with a perfect powder coating so if you see a spot on the slider that has scratches or the powder coating shows a blemish; that’s a good indication of a friction point. Using a file or other grinding tool to smooth over a small area on the slider can alleviate this problem. Thank you for choosing Rock-Slide Engineering products.
