Robustel GoRugged R3000 NU Industrial VPN Router User Guide Document Name: Firmware : Date : Status : Doc ID : User Guide 1.01.00 2014-03-24 Confidential )RT_UG_R3000 NU_v.1.0.0 www.robustel.
Robustel GoRugged R3000 NU User Guide About This Document This document describes hardware and software of Robustel R3000 NU, Industrial VPN Router. Copyright© Guangzhou Robustel Technologies Co., Limited All Rights Reserved. Trademarks and Permissions Robustel are trademark of Guangzhou Robustel Technologies Co. Limited. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Robustel GoRugged R3000 NU User Guide Regulatory and Type Approval Information Table 1: Directives 2002/95/EC Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) 2002/96/EC Directive of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE) Directive of the European Parliament and of the Council of 8 December 2003/108/EC 2003 amending
Robustel GoRugged R3000 NU User Guide Revision History Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions. Release Date Firmware Version Doc Version Details 2014-01-17 1.01 v.1.0.0 First Release RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Contents Chapter 1. 1.1 1.2 1.3 1.4 Chapter 2. 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Chapter 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 Product Concept......................................................................................................................................... 6 Overview ...........................................................................................
Robustel GoRugged R3000 NU User Guide 3.29 Configuration -> Reboot ........................................................................................................................... 78 3.30 Configuration -> RobustLink ..................................................................................................................... 79 3.31 Configuration -> Syslog............................................................................................................................. 79 3.
Chapter 1. Product Concept 1.1 Overview Robustel GoRugged R3000 NU is a rugged VPN router offering state-of-the-art secure connectivity for machine to machine (M2M) applications. WAN link management: Ethernet WAN/WLAN WAN backup. VPN tunnel: IPSec/OpenVPN/PPTP/L2TP/GRE. Supports Modbus gateway (Modbus RTU/ASCII to Modbus TCP). Supports GPS (optional), provides real time location and tracking. Supports 802.11 b/g/n Wi-Fi (optional), AP and client mode.
Robustel GoRugged R3000 NU User Guide 3-pin pluggable terminal block with lock for power connector x 1 7-pin pluggable terminal block with lock for serial port, I/O and console port x 1 CD with user guide x 1 Note: Please notify your sales representative if any of the above items are missing or damaged. Ethernet cable x 1 Wall Mounting Kit 35mm Din-Rail mounting kit RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide AC/DC Power Supply Adapter (12VDC, 1.5A) x 1 (EU, US, UK, AU plug optional) 1.3 Specifications Ethernet Interface Number of Ports: 2 x 10/100 Mbps, 1 LAN+1 WAN Magnet Isolation Protection: 1.5KV WLAN Interface (Optional) Standards: 802.11b/g/n up to 65 Mbps, AP and Client mode Frequency Band: 2.400 - 2.500 GHz (2.4 GHz ISM band) Security: Open ,WPA, WPA2 Encryption: AES, TKIP Antenna Interface: SMA Female Transmission Power: 802.
Robustel GoRugged R3000 NU User Guide Serial Interface Number of Ports: 1 x RS-232, 1 x RS-485 or 2 x RS232 or 2 x RS485 ESD Protection: ±15KV Parameters: 8E1, 8O1, 8N1, 8N2, 7E2, 7O2, 7N2, 7E1 Baud Rate: 300bps to 230400bps RS-232: TxD, RxD, RTS, CTS, GND RS-485: Data+ (A), Data- (B), GND Interface: 3.
Robustel GoRugged R3000 NU User Guide VPN tunnel: IPSec/OpenVPN/PPTP/L2TP/GRE Firewall: SPI, anti-DoS, Filter, Access Control Management: Web, CLI, SNMP v1/v2/v3, RobustLink Serial Port: TCP client/server, UDP, Modbus RTU/ASCII to Modbus TCP, Virtual COM (COM port redirector) RobustLink: Centralized M2M management platform Power Supply and Consumption Power Supply Interface: 5mm terminal block with lock Input Voltage: 9 to 60 VDC Power Consumption: Idle: 100 mA @ 12 V Dat
Robustel GoRugged R3000 NU User Guide Chapter 2. Installation 2.1 LED Indicators Name RUN WLAN USR Color Green Green Green Status Function Blinking Router is ready. On Router is starting. Off Router is power off. Blinking WLAN Indicator: Data is being transmitted. On WLAN Indicator: Wi-Fi AP/Client is enabled. Off WLAN Indicator: Wi-Fi AP/Client is disabled. On/Blinking VPN tunnel/PPPoE/DynDNS/GPS is up. Off VPN tunnel/PPPoE/ DynDNS/GPS is down.
Robustel GoRugged R3000 NU User Guide 2.2 PIN assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PIN Debug 1 RXD 2 TXD 3 GND RS232 Power Digital I/O RS485 GND 4 TXD 5 RXD 6 RTS 7 CTS 8 Positive 9 Negative 10 GND 11 Input 1 12 Input 2 13 Output 1 14 Output 2 15 GND 16 Data+(A) 17 Data- (B) 2.3 USB interface USB interface is used for batch firmware upgrade, cannot used to send or receive data from slave devices which with USB interface.
Robustel GoRugged R3000 NU User Guide 2.4 Reset Button Function Operation Reboot Push the button for 5 seconds under working status. Restore to factory default setting Push the button for 60 seconds once you power on the router until all the three LEDs at the left side (RUN, PPP, USR) blink at the same time for 5 times. Reset Button 2.5 Ethernet ports Each Ethernet port has two LED indicators (please check the following picture). The yellow one is Speed indicator and the green one is Link indicator.
Robustel GoRugged R3000 NU User Guide 2.6 Mount the Router Use 2 pcs of M3 screw to mount the router on the wall. Or mount the router on a DIN rail with 3 M3 screws. 2.7 Ground the Router Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices. Screw Note: This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel.
Robustel GoRugged R3000 NU User Guide Chapter 3. Configuration settings over web browser The router can be configured through your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me/Vista/7/8, etc. The product provides an easy and user-friendly interface for configuration. There are various ways to connect the router, either through an external repeater/hub or connect directly to your PC.
Robustel GoRugged R3000 NU User Guide 4. Select Internet Protocol (TCP/IP) and click Properties. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 5. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 3.2 Factory Default Settings Before configuring your router, you need to know the following default settings. Item Username Password Eth0 Eth1 DHCP Server Description admin admin 192.168.0.1/255.255.255.0, LAN mode 192.168.0.1/255.255.255.0, LAN mode Enabled. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 3.3 Control Panel This section allows users to save configuration, reboot router, logout and select language. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Control Panel Item Description Button Save Click to save the current configuration into router’s flash. Reboot After save the current configuration, router needs to be rebooted to make the modification taking effect. Logout Click to return to the login page. Language Select from Chinese, English, German, French and Spanish. Refresh Click to refresh the status. Apply Click to apply the modification on every configuration page.
Robustel GoRugged R3000 NU User Guide Router Information Item Device Model Serial Number Device Name Firmware Version Hardware Version Kernel Version Uptime CPU Load RAM Total/Free System Time Description Show the model name of this device Show the serial number of this device Show the device name to distinguish different devices you have installed.
Robustel GoRugged R3000 NU User Guide Keeping PING IP Address Keeping PING Interval Show the current ICMP detection server which you can set in “Configuration->Link Management”. Show the ICMP Detection Interval (s) which you can set in “Configuration->Link Management”. 3.5 Status -> Network This section displays the router’s Network status, which include status of ETH0, ETH1, WLAN (AP mode)/WLAN (Client mode). Note: This information will be shown when R3000 NU enable WiFi feature and works as AP mode.
Robustel GoRugged R3000 NU User Guide Note: This information will be shown when R3000 NU enable WLAN and works as Client mode. 3.6 Status -> Route This section displays the router’s route table. 3.7 Status -> VPN This section displays the router’s VPN status, which includes IPSec, L2TP, PPTP, OpenVPN and GRE. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 3.8 Status -> Services This section displays the router’s Services’ status, including VRRP, DynDNS, Serial and DI/DO. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 3.9 Status -> Event/Log This section displays the router’s event/log information. You need to enable router to output the log and select the log level first, then you can view the log information here. Also you can click Download System Diagnosing Data to download diagnose data. Event/Log Item Download Log Level RT_UG_R3000 NU_v.1.0.0 Confidential Description Select the log messages you want to download.
Robustel GoRugged R3000 NU User Guide Download Sytem Diagnosing Data Click Download System Diagnosing Data to download diagnose file. Manual Refresh Select from “5 Seconds”, “10 Seconds”, “15 Seconds”, “30 Seconds” and “1 Minute”. User can select these intervals to refresh the log information. 3.10 Configuration -> Link Management This section allows users to set the WAN link and the related parameters. Link Management Item Description Selected from “Eth0”, “WiFi”. Primary Interface 1.
Robustel GoRugged R3000 NU User Guide Reset The Interface Enable to reset the Eth0 interface after the max ICMP detection retries. 3 3.11 Configuration -> Ethernet This section allows users to set the Ethernet WAN and LAN parameters of Eth0. When “Ethernet Interface Type” is selected as “LAN” type: Eth0@Ethernet Item Ethernet Interface Type RT_UG_R3000 NU_v.1.0.0 Confidential Description Eth0 can work under two different kinds of mode: LAN and WAN. 24.03.
Robustel GoRugged R3000 NU User Guide Enable Bridge @ LAN Interface IP Address, Netmask, MTU, Media Type@ LAN Interface Multiple IP Address @ LAN Interface Enable DHCP Server @ DHCP Server IP Pool Start, IP Pool End @ DHCP Server Enable to make Eth0 works under bridge mode with Eth1. Eth0 and Enable Eth1 will have the same IP address under this mode. Set the IP address, Netmask, MTU and Media Type of Eth0. These Null parameters will be un-configurable if you enable Bridge.
Robustel GoRugged R3000 NU User Guide Eth0@Ethernet Item Ethernet Interface Type Description Eth0 can work under two different kinds of mode: LAN and WAN. Select from “Static IP”, “DHCP Client” and “PPPoE(ADSL)”. Static IP: Set up the IP address manually. WAN Interface Type @ DHCP Client: Eth0’s IP address will be assigned automatically by the WAN Interface network’s DHCP Server.
Robustel GoRugged R3000 NU User Guide Secondary DNS Server, of Eth0 when WAN Interface is set as “DHCP Client”. MTU, Netmask, Gateway @ DHCP Client Username, Password, Connection Mode, Redial Set Username, Password, Connection Mode, Redial Interval, Retries of Interval, Retries @ Eth0 when WAN Interface is set as “PPPoE(ADSL)”. PPPoe(ADSL) / This section allows users to set the Ethernet LAN parameters of Eth1.
Robustel GoRugged R3000 NU User Guide Multiple IP Address @ Assign multiple IP addresses for Eth1. Null LAN Interface Enable DHCP Server @ Enable to make router can lease IP address to DHCP clients which Enable DHCP Server connect to Eth1. 192.168.0.2/ IP Pool Start, IP Pool End Define the beginning (IP Pool Start) and end (IP Pool End) of the pool of 192.168.0.10 @ DHCP Server IP addresses which will lease to DHCP clients. 0 Define the Netmask which the DHCP clients will obtain from DHCP 255.255.255.
Robustel GoRugged R3000 NU User Guide Router can be DHCP Relay, which will provide a relay tunnel to solve problem that DHCP Client and DHCP Server is not in a same subnet. This section allow user to configure DHCP Relay settings. DHCP Relay@Ethernet Item Description Default Enter DHCP Server’s IP address. DHCP Server Note: Please disable DHCP Server and DHCP Client first to make sure Null DHCP relay can be enabled. Note: IP Address and NetMask will be hidden if user bridge two Ethernet ports. 3.
Robustel GoRugged R3000 NU User Guide Note: when R3000 NU enable WiFi feature and works as Client mode Basic @ WiFi Item Enable WiFi Mode Channel SSID RT_UG_R3000 NU_v.1.0.0 Confidential Description Click to enable WiFi feature. This item will show “AP” and “Client”, cannot be configured. AP: In a wireless local area network (WLAN), an access point is a station that transmits and receives data.
Robustel GoRugged R3000 NU User Guide Hide SSID Security mode Encryption Passphrase Key Renewal Interval(s) WiFi Network Settings RT_UG_R3000 NU_v.1.0.0 Confidential When R3000 NU works as AP mode, after clicking this check box R3000 NU will not broadcast the SSID. Other wireless devices cannot discover this access point automatically. User need to enter the SSID manually to let their wireless devices join this access point.
Robustel GoRugged R3000 NU User Guide Note: Available when R3000 NU enable WiFi feature and works as AP mode Enable ACL Mode Access Control List BSSID SSID RT_UG_R3000 NU_v.1.0.0 Confidential Mac Filter @ WiFi (Only for AP mode) Click to enable ACL (Access Control List). Disable Select from “Allow” and “Deny”. Allow: Only the packets fitting the entities of the “Access Control List” can be allowed. Deny: All the packets fitting the entities of the “Access Control List” will Allow be denied.
Robustel GoRugged R3000 NU User Guide Mode Key Management Cipher Pairwise Cipher Group WPA State R3000 NU connects to. Show current mode of R3000 NU: AP or Client. Show current security mode of R3000 NU or the access point which R3000 NU connects to. Show current encryption algorithm of R3000 NU or the access point which R3000 NU connects to. Show current WPA status. Mainly there are 5 statuses: Disconnected, Scanning, Initializing, Associated, 4way_handshark, Completed.
Robustel GoRugged R3000 NU User Guide When Select Protocol “Transparent”: When Select Protocol “Modbus”: When Select Protocol “Transparent Over Rlink”: RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide When Select Protocol “Modbus Over Rlink”: RS232 @ Serial Item Baud-rate Data bit Parity Stop bit Flow control Protocol Mode @Transparent Local @Transparent Port Description Select from “300”, “600”, “1200”, “2400”, “4800”, “9600”, “19200”, “38400”, “57600” , “115200”and “230400”. Select from “7” and “8”. Select from “None”, “Odd” and “Even”. Select from “1” and “2”. Select from “None”, “Software” and “Hardware”.
Robustel GoRugged R3000 NU User Guide via VPN tunnel. Note: when you do not enable any VPN tunnel, this item will not show up. The serial port will queue the data in the buffer and send the data to the Interval Timeout Ethernet WAN when it reaches the Interval Timeout in the field. @Transparent Note: Data will also be sent as specified by the packet length or delimiter settings even when data is not reaching the interval timeout in the field.
Robustel GoRugged R3000 NU User Guide Modbus ASCⅡ protocol. Note: When select “Modbus RTU master” and “Modbus ASCⅡmaster” protocol, router is as TCP Client site, user need to enter slave address and slave port number in “Slave Address @ Modbus Slave ” and “Slave Port @ Modbus Slave”, and connect to Server site. Add the Modbus slaves which will be polled by Modbus master (router).
Robustel GoRugged R3000 NU User Guide When Select Protocol “Modbus”: When Select Protocol “Transparent Over Rlink”: When Select Protocol “Modbus Over Rlink”: RS485 @ Serial Item Baud-rate Data bit Parity Stop bit Protocol RT_UG_R3000 NU_v.1.0.0 Confidential Description Select from “300”, “600”, “1200”, “2400”, “4800”, “9600”, “19200”, “38400”, “57600” , “115200”and “230400”. Select from “7” and “8”. Select from “None”, “Odd” and “Even”. Select from “1” and “2”.
Robustel GoRugged R3000 NU User Guide protocols. Modbus: Router will transmit the serial data with Modbus protocol. Select from “TCP Server”, “TCP Client” and “UDP”. Mode @Transparent Local Port Enter the Local port for TCP or UDP. @Transparent Click “Add” button to add multiple server. You need to enter the server’s IP and port, and enable or disable “Send data to serial”. If you disable “Send Multiple Server data to serial”, router will not transmit the data from this server to serial @Transparent port.
Robustel GoRugged R3000 NU User Guide or received via VPN tunnel. Note: when you do not enable any VPN tunnel, this item will not show up. Local Port @ Modbus Enter the Local port for Modbus. Select From “Modbus RTU slave”, “Modbus ASCⅡ slave”, “Modbus RTU master” and “Modbus ASCⅡ master”. Modbus RTU slave: router connects to slave device which works under Modbus RTU protocol. Attached serial device Modbus ASCⅡ slave: router connects to slave device which works under type @ Modbus Modbus ASCⅡprotocol.
Robustel GoRugged R3000 NU User Guide DI @ DI/DO Item Enable DI Mode Filtering Count Trigger Counter Active Counter Start Power On Description Click to Enable DI. Select from “OFF”, “ON”, “EVENT_COUNTER”. OFF: Connect to GND (logic 0). When pin DI connects to GND, R3000 NU will detect there is a DI alarm input. ON: Open from GND (logic 1). When pin DI does not connect to GND, R3000 NU will detect there is a DI alarm input. EVENT_COUNTER: under event counter mode.
Robustel GoRugged R3000 NU User Guide DO @ DI/DO Item Enable Description Click to enable DO. Digital Output initiates according to different alarm source. Selected from “DI Alarm”. Alarm Source DI Alarm: Digital Output triggers the related action when there is alarm from Digital Input. Digital Output initiates when there is an alarm. Selected from “OFF”, “ON”, “Pulse”. OFF: Open from GND when triggered. Alarm On Action ON: Short contact with GND when triggered.
Robustel GoRugged R3000 NU User Guide Delay Low High Output Available when enable Pulse in Alarm On Action/Alarm Off Action. The first pulse will be generated after a “Delay”. Input from 0 to 30000ms. (0=generate pulse without delay) Available when enable Pulse in Alarm On Action/Alarm Off Action. In Pulse Output mode, the selected digital output channel will generate a square wave as specified in the pulse mode parameters. The low level widths are specified here. Input from 1 to 30000 ms.
Robustel GoRugged R3000 NU User Guide GPS Setting @ GPS Item Enable GPS Report To RS232 RS232 Report Type Description Click to enable GPS function. Click to enable GPS report to RS232 serial port of router. Select from “NMEA GGA+VTG”, “NMEA GGA+VTG+RMC” and “NMEA RMC”. NMEA GGA+VTG: Global Positioning System Fix Data（GGA）+ Track Made Good and Ground Speed（VTG）.
Robustel GoRugged R3000 NU User Guide Report Type Report Interval Socket Type Select from “NMEA GGA+VTG”, “NMEA GGA+VTG+RMC” and “NMEA RMC”. NMEA GGA+VTG: Global Positioning System Fix Data（GGA）+ Track Made Good and Ground Speed（VTG）. NMEA GGA+VTG+RMC: Global Positioning System Fix Data（GGA）+ Track Made Good and Ground Speed（VTG）+ Recommended Minimum Specific GPS/TRANSIT Data（RMC）. NMEA RMC: Recommended Minimum Specific GPS/TRANSIT Data（RMC）. Set the interval to report GPS status to GPS Server.
Robustel GoRugged R3000 NU User Guide Satellites In Use Satellites In View UTC Latitude Longitude Altitude Speed Setting” yet). No Fix/Invalid: GPS function is enabled, but do not get GPS signal (User should put router outdoor to get stronger GPS signal). Standalone GPS Fix: Standalone GPS techniques is a mature, universal GPS positioning mode, only get position from satellite. Differential GPS Fix: Differential GPS techniques are used to enhance the quality of location data.
Robustel GoRugged R3000 NU User Guide Port Forwarding @ NAT/DMZ Item Port Forwarding Defaul t Description Manually defining a rule in the router to send all data received on some range of ports on the internet side to a port and IP address on the LAN side. Set the remote IP address. The port of the internet side which you want to forward to LAN side. Remote IP Arrives At Port Is Forwarded to IP The device’s IP on the LAN side which you want to forward the data to.
Robustel GoRugged R3000 NU User Guide Basic @ Firewall Item Remote Access Using HTTP Remote Access Using TELNET Remote Access Using SNMP Remote Ping Request Defend Dos Attack Description Default Enable to allow users to access the router remotely on the internet side via HTTP. Enable Enable to allow users to access the router remotely on the internet side via Telnet. Enable to allow users to access the router remotely on the internet side via SNMP.
Robustel GoRugged R3000 NU User Guide Port. Select from “TCP”, “UDP”, “TCP&UDP”, “ICMP” or “ALL”. Protocol If you don’t know what kinds of protocol of your application, we recommend you TCP select “ALL”. Note: You can use “-“to define a range of IP addresses or ports, e.g. 1.1.1.1-2.2.2.2, 10000-12000. Note: the filtering settings should be divided into two parts. Part 1 is the Exact Filter List and Part 2 is the Default Filter Policy. The priority of Exact Filter List is higher than Default Filter Policy.
Robustel GoRugged R3000 NU User Guide QoS Item Enable QoS Downlink (kbps) Description Click to enable “QoS” function. Speed Prescribe downlink speed of router. Note: Default setting“0” means that there is no limitation of downlink speed. Prescribe uplink speed of router. uplink Speed (kbps) Note: Default setting“0” means that there is no limitation of uplink speed.
Robustel GoRugged R3000 NU User Guide Optimize for Serial Data Forwarding Optimize for ICMP MAC Address @ QoS MAC Control List Priority @ QoS MAC Control List IP Address @ QoS IP Control List Priority @ QoS IP Control List RT_UG_R3000 NU_v.1.0.0 Confidential Speed”, and the maximum rate can reach to 100% of “Downlink Speed”. Normal: guarantees that the minimum global rate of router is 10% of “Downlink Speed”, and the maximum rate can reach to 100% of “Downlink Speed”.
Robustel GoRugged R3000 NU User Guide Exempt: this is the highest priority which guarantees that the minimum global rate of router is 50% of “Downlink Speed”, and the maximum rate can reach to 100% of “Downlink Speed”. Premium: guarantees that the minimum global rate of router is 25% of “Downlink Speed”, and the maximum rate can reach to 100% of “Downlink Speed”.
Robustel GoRugged R3000 NU User Guide Static Route @ IP Routing Item Static Route Table Interface Destination Netmask Gateway Description Allow users to add, delete or modify static route rules manually. Select from “WAN”, “LAN_0” or “LAN_1”. Enter the destination host’s IP address or destination network. Enter the Netmask of the destination or destination network. Enter the gateway’s IP address of this static route rule.
Robustel GoRugged R3000 NU User Guide Setting RIP Protocol Version Select from “RIPv1” and “RIPv2”. If you input this neighbor IP, router will only send RIP request massage to this IP Neighbor IP instead of broadcast. This item only needs to be set in some unicast network. Defines the interval between routing updates. Update times Defines the route aging time. If no update for a route is received after the aging Timeout time elapses, the metric of the route is set to 16 in the routing table.
Robustel GoRugged R3000 NU User Guide Enable OSPFv2 Tick to enable OSPF function. Disable 3.21 Configuration -> DynDNS This section allows users to set the DynDNS parameters. DynDNS Item DynDNS Enable DynDNS Service Type hoastmen Username Password URL Force Update DynDNS Status RT_UG_R3000 NU_v.1.0.
Robustel GoRugged R3000 NU User Guide 3.22 Configuration -> IPSec This section allows users to set the IPSec parameters. IPSec Basic @ IPSec Item Enable NAT Traversal Keepalive Interval RT_UG_R3000 NU_v.1.0.0 Confidential Description Tick to enable NAT Traversal for IPSec. This item must be enabled when router under NAT environment. The interval that router sends keepalive packets to NAT box so that to avoid it to remove the NAT mapping. 24.03.
Robustel GoRugged R3000 NU User Guide IPSec Tunnel @ IPSec Item Add Enable IPSec Gateway Address IPSec Mode IPSec Protocol RT_UG_R3000 NU_v.1.0.0 Confidential Description Click Add to add new IPSec Tunnel Enable IPSec Tunnel, the max tunnel account is 3 Default Null Null Enter the address of remote side IPSec VPN server. Null Select from “Tunnel” and “Transport”. Tunnel: Commonly used between gateways, or at an end-station to a gateway, the gateway acting as a proxy for the hosts behind it.
Robustel GoRugged R3000 NU User Guide Local Subnet Local Subnet Mask Local ID Type Remote Subnet Remote Subnet Mask Remote ID Type Negotiation Mode Encryption Algorithm Authentication Algorithm DH Group RT_UG_R3000 NU_v.1.0.0 Confidential ESP: Uses the ESP protocol. AH: Uses the AH protocol. Enter IPSec Local Protected subnet’s address. Enter IPSec Local Protected subnet’s mask. Select from “IP Address”, “FQDN” and “User FQDN” for IKE negotiation. “Default” stands for “IP Address”.
Robustel GoRugged R3000 NU User Guide Authentication Secrets Life Time @ IKE Parameter SA Algorithm PFS Group Life Time @ SA Parameter DPD Time Interval Select from “PSK”, “CA”, “XAUTH Init PSK” and “XAUTH Init CA” to be used in IKE negotiation. PSK: Pre-shared Key. CA: Certification Authority. XAUTH: Extended Authentication to AAA server. Enter the Pre-shared Key. Set the lifetime in IKE negotiation. Before an SA expires, IKE negotiates a new SA.
Robustel GoRugged R3000 NU User Guide ICMP Server Detection ICMP Detection Local IP ICMP Detection Interval ICMP Detection Timeout ICMP Detection Retries Enter the IP address or domain name or remote server. Router will ping this address/domain name to check that if the current connectivity is Null active. Set the local IP address. Null Set the ping interval time. 30 Set the ping timeout.
Robustel GoRugged R3000 NU User Guide 3.23 Configuration -> Open VPN This section allows users to set the Open VPN parameters. Client @ Open VPN Item Enable Protocol Remote IP Address Port Description Enable OpenVPN Client, the max tunnel account is 3 Select from “UDP” and “TCP Client” which depends on the application. Enter the remote IP address or domain name of remote side OpenVPN server. Enter the listening port of remote side OpenVPN server. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Interface Authentication Local IP Remote IP Enable NAT Ping Interval Ping -Restart Compression Encryption MTU Max Frame Size Verbose Level Expert Options Subnet&Subnet Mask@Local Route Select from “tun” and “tap” which are two different kinds of device interface for OpenVPN. The difference between tun and tap device is this: a tun device is a virtual IP point-to-point device and a tap device is a virtual Ethernet device.
Robustel GoRugged R3000 NU User Guide Server @ Open VPN Item Enable Server OpenVPN Tunnel name Listen IP Protocol Port Interface RT_UG_R3000 NU_v.1.0.0 Confidential Description Default Tick to enable OpenVPN server tunnel. Disable Name the OpenVPN server tunnel. Tunnel_OpenVPN_ 0 You can enter the IP address of Ethernet WAN or Ethernet LAN. Null or 0.0.0.0 stands for using the active WAN link currently Ethernet WAN. Select from “UDP” and “TCP Client” which depends on the application.
Robustel GoRugged R3000 NU User Guide Authentication Local IP Remote IP Enable NAT Ping Interval Ping -Restart Compression Encryption MTU Max Frame Size Verbose Level Expert Options Client Manage RT_UG_R3000 NU_v.1.0.0 Confidential device. Select from four different kinds of authentication ways: “Pre-shared”, “Username/Password”, “X.509 cert” and “X.509 cert+user”. Define the local IP address of OpenVPN tunnel. Define the remote IP address of OpenVPN tunnel. Tick to enable SNAT for OpenVPN.
Robustel GoRugged R3000 NU User Guide X.509 @ Open VPN Item Select Cert Type CA Public Key Private Key DH TA CRL Pre-Share Static Key Description Select the OpenVPN client or server which the certification used for. Click “Browse” to select the correct CA file from your PC, and then click “Import” to import it to the router. Click “Export” you can export the CA file from router to your PC.
Robustel GoRugged R3000 NU User Guide GRE Item Add Enable Remote IP Address Local Virtual IP Remote virtual IP Remote Subnet Description Click “Add” to add a GRE tunnel. Click to enable GRE (Generic Routing Encapsulation). GRE is a protocol that encapsulates packets in order to route other protocols over IP networks. Set remote IP Address of the virtual GRE tunnel. Set local IP Address of the virtual GRE tunnel. Set remote IP Address of the virtual GRE tunnel.
Robustel GoRugged R3000 NU User Guide L2TP Client @ L2TP Item Description Default Add Click “Add” to add a L2TP client. You can add at most 3 L2TP clients. Null Remote IP Address Username Password Enter your L2TP server’s public IP or domain name. Enter the username which was provided by your L2TP server. Enter the password which was provided by your L2TP server. Select from “Auto”, “PAP”, “CHAP”, “MS-CHAP v1” and “MS-CHAP v2”.
Robustel GoRugged R3000 NU User Guide Remote Subnet Remote Subnet Mask Enable NAT All traffic via this interface Enable Tunnel Authentication Tunnel Secret Show Advanced Port Local IP Remote IP server’s authentication method. When you select “Auto”, router will auto select the correct method based on server. Enter L2TP remote Protected subnet’s address. Enter L2TPremote Protected subnet’s mask. Click to enable NAT feature of L2TP.
Robustel GoRugged R3000 NU User Guide L2TP Server @ L2TP Item Enable L2TP Server Username Password Description Tick to enable L2TP server. Set the username which will assign to L2TP client. Set the password which will assign to L2TP client. Select from “PAP”, “CHAP”, “MS-CHAP v1” and “MS-CHAP v2”. Authentication L2TP client need to select the same authentication method based on this server’s authentication method.
Robustel GoRugged R3000 NU User Guide Show L2TP Server Tick to show the L2TP server advanced setting. Advanced Address/Control Used for PPP initialization. In general, you need to enable it as default. Compression Protocol Field Used for PPP initialization. In general, you need to enable it as default. Compression One of the L2TP initialization strings. In general, you don’t need to modify this Asyncmap Value value. Maximum Receiving Unit.
Robustel GoRugged R3000 NU User Guide PPTP Client @ PPTP Item Add Enable Disable Remote IP Address Username Password Authentication Enable NAT Enable MPPE All traffic via interface Show Advanced this RT_UG_R3000 NU_v.1.0.0 Confidential Description Click “Add” to add a PPTP client Enable PPTP Client. The max tunnel accounts are 3. Disable PPTP Client. Enter your PPTP server’s public IP or domain name. Enter the username which was provided by your PPTP server.
Robustel GoRugged R3000 NU User Guide Local IP Remote IP Set the IP address of the PPTP client. You can enter the IP which assigned by PPTP server. Null means PPTP client will obtain an IP address automatically from PPTP server’s IP pool. Enter the remote peer’s private IP address or remote subnet’s gateways address. Address/Control Used for PPP initialization. In general, you need to enable it as default. Compression Protocol Field Used for PPP initialization.
Robustel GoRugged R3000 NU User Guide PPTP Server @ PPTP Item Enable PPTP Server Username Password Authentication Local IP IP Pool Start IP Pool End Enable MPPE Description Tick to enable PPTP server. Set the username which will assign to PPTP client. Set the password which will assign to PPTP client. Select from “PAP”, “CHAP”, “MS-CHAP v1” and “MS-CHAP v2”. PPTP client need to select the same authentication method based on this server’s authentication method. Set the IP address of PPTP server.
Robustel GoRugged R3000 NU User Guide MTU Link Detection Interval Maximum Transmission Unit. It is the identifier of the maximum size of packet, which is possible to transfer in a given environment. Specify the interval between PPTP client and server. To check the connectivity of a tunnel, the client and server regularly send PPP Echo to each other. If the client or server receives no response from the peer within a specified period of time, it retransmits the PPP echo.
Robustel GoRugged R3000 NU User Guide View @ SNMP Item View Name View Filter View OID Description Enter the View Name Select from “Include” and “Exclude”. Enter the Object Identifiers (OID) Default Null Include Null VACM @ SNMP Item Readwrite Network Community MIBview RT_UG_R3000 NU_v.1.0.0 Confidential Description Select the access rights from “Readonly” and “ReadWrite”. Define the network from which is allowed to access. E.g. 172.16.0.0. Enter the community name.
Robustel GoRugged R3000 NU User Guide Trap @ SNMP Item Enable SNMP Trap Version Server Address Port Name Description Click to enable SNMP Trap feature. Select from “SNMPv1”, “SNMPv2” and “SNMPv3”. Enter SNMP server’s IP address. Enter SNMP server’s port number Enter SNMP server’s name. Default Disable SNMPv1 Null 0 Null 3.28 Configuration -> VRRP This section allows users to set the VRRP parameters.
Robustel GoRugged R3000 NU User Guide Time @ Reboot Item Enable(ahh:mm,24h) Reboot Time1 Reboot Time2 Reboot Time3 Description Enable daily reboot, you should follow ahh:mm,24h time frame, or the data will be invalid. Specify time1 when you need router reboot. Specify time2 when you need router reboot. Specify time3 when you need router reboot. Default Disable 12:00 Null Null 3.
Robustel GoRugged R3000 NU User Guide Syslog Item Save Position Log Level Keep Days Log to Remote System Description Select the save position from “None”, “Flash” and “SD”. “None” means syslog is only saved in RAM, and will be cleared after reboot. Select form “DEBUG”, “INFO”, “NOTICE”, “WARNING”, “ERR”, “CRIT”, “ALERT” and “EMERG” which from low to high. The lower level will output more syslog in detail. Specify the syslog keep days for router to clear the old syslog.
Robustel GoRugged R3000 NU User Guide Event Item Enable Event Description Click to enable Event feature. This feature is used to report R3000 NU’s main running event to SNMP-TRAP or RobustLink. There are numbers of Event code you can select, such as “BOOT-UP”, “3G-UP”, “3G-DOWN”, etc. For example if you click “3G-UP” and select “RobustLink” as the server, when R3000 NU dial up to connect to 3G network, it will send event code “3G-UP” as well as relevant information to RobustLink. Default Disable 3.
Robustel GoRugged R3000 NU User Guide Item USR LED Type Indication Description Default Select from “VPN”, “PPPoE”, “DynDNS” and “GPS”. VPN Select from “ON”, “Blink”. For example, if “USR LED Type” is set as “VPN” and “Indication” is set as “Blink”, ON when any VPN tunnel is up USR LED will blink. 3.34 Administration -> Profile This section allows users to import or export the configuration file, and restore the router to factory default setting.
Robustel GoRugged R3000 NU User Guide 3.35 Administration -> Tools This section provides users four tools: Ping, AT Debug, Traceroute and Test. Ping @ Tools Item Ping IP address Number of requests Timeout Local IP Start RT_UG_R3000 NU_v.1.0.0 Confidential Description Enter the ping destination IP address or domain name. Specify the number of ping requests. Specify timeout of ping request. Specify the local IP from Ethernet WAN or Ethernet LAN.
Robustel GoRugged R3000 NU User Guide Traceroute @ Tools Item Trace Address Trace Hops Timeout Send RT_UG_R3000 NU_v.1.0.0 Confidential Description Enter the trace destination IP address or domain name. Specify the max trace hops. Router will stop tracing if the trace hops has met max value no matter the destination has been reached or not. Specify timeout of Traceroute request. Click this button to start Traceroute request, and the log will be displayed in the follow box. 24.03.
Robustel GoRugged R3000 NU User Guide Sniffer @ Tools Item Interface Host Protocol Start RT_UG_R3000 NU_v.1.0.0 Confidential Description Select form “all”, “lo”, “imq0”, “imq1”, “eth0”, “gre0”: all: contain all the interface; lo: Local Loopback interface; imq0/1: virtual interface for QoS, which used to limit the download and upload speed; eth0: Ethernet interface; gre0: GRE tunnel interface; Filter the packet that contain the specify IP address. Select from “all”, “ip”, “arp”, “tcp” and “udp”.
Robustel GoRugged R3000 NU User Guide Test @ Tools Item Description Click “Enable” to select the hardware component whose status you want to Enable check. Select from “SD Test”, “USB Test”, “Flash Test”, “Memory Test”, “Ethernet Test”, Description “SIM1 Test”, “SIM2 Test” and “Module Test”. Show the current status of the selected hardware component. There are 3 status “Testing”, “Success” and “Failure”. Testing: Router is testing the selected hardware component.
Robustel GoRugged R3000 NU User Guide Clock Item Real Time Clock PC Time Synchronize Enable NTP Client Description Router’s RTC can be showed and modified in this field. You PC’s time can be showed here. Synchronize router’s RTC with PC. Enable to synchronize the time from NTP server. Timezone @ Client Select your local time zone. Primary NTP Server Enter primary NTP Server’s IP address or domain name.
Robustel GoRugged R3000 NU User Guide Basic @ Web Server Item HTTP Port HTTPS Port HTTPS Certificate Description Enter the HTTP port number you want to change in R3000 NU’s Web Server. On a Web server, port 80 is the port that the server "listens to" or expects to receive from a Web client. If you configure the router with other HTTP Port number except 80, only adding that port number then you can login R3000 NU’s Web Server. Enter the HTTPS port number you want to change in R3000 NU’s Web Server.
Robustel GoRugged R3000 NU User Guide Super @ User Management Item Super User Management Login Timeout Description One router has only one super user account. Under this account, user has the highest authority include modify and add management user accounts. Set Username and Password. Specify the login timeout value. You need to re-login after this timeout of user inactively.
Robustel GoRugged R3000 NU User Guide List you want to start up, as well as the running information. Enable: Click to enable the APP file. APP Name: Shows the name of the APP files. Options: It is an optional items, user can choose to configure startup parameters here. Memory (KB): Shows the memory resources occupied by the APP files. Running: Shows whether the APP files are running. Files @ SDK Management Item Import Files Custom File List Description Click to import configuration files in this item.
Robustel GoRugged R3000 NU User Guide “Update” button” to update. After updating successfully, you need to reboot router to take effect. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Chapter 4. Configuration Examples 4.1 Interface 4.1.1 Console port User can use the console port to manage the router via CLI commands, please check section Introductions for CLI. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 4.1.2 Digital Input There are two digital inputs of R3000, it just support dry contact (do not supports wet contact). Please check the connector interface of R3000, you can find out “V-” easily at one of the pin of power input connector. 4.1.3 Digital Output There are two digital outputs of R3000. Power negative of DC should connect to “GND” Please refer to connection diagram at the right site. Maximum voltage/current/output power of DO is 36VDC/0.05A/0.3W.
Robustel GoRugged R3000 NU User Guide 4.1.4 RS232 R3000 supports one RS232 for serial data communication. Please refer to the connection diagram at the right site. 4.1.5 RS485 R3000 supports one RS485 for serial data communication. Please refer to the connection diagram at the right site. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 4.2 Network 4.2.1 NAT This section shows users how to set the NAT configuration of router. Parameter Remote IP defines if access is allowed to route to the Forwarded IP and Port via WAN IP and “Arrives At Port”. Configuration--->NAT/DMZ--->Port Forwarding Explanations for above diagram: If there are two IP addresses 58.1.1.1 and 59.1.1.1 for the External Devices, that the result will be different from the test when the NAT is working at R3000 NU. 58.1.1.
Robustel GoRugged R3000 NU User Guide 4.2.2 L2TP L2TP_SERVER: Configuration--->L2TP--->L2TP Server Tick “Enable L2TP Server”, and fill in the blank textbox RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide The modification will take effect after “Apply-->Save-->Reboot”. Note: The following diagrams with red color numbers mean these are the matches between server and client, and with the blue color number means it must be set locally for the tunnel. L2TP_CLIENT: Configuration--->L2TP--->L2TP Client Click “Add” button, and fill in the blank textbox The modification will take effect after “Apply-->Save-->Reboot”. 4.2.3 PPTP RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Note: The following diagrams with red color numbers mean these are the matches between server and client, and with the blue color number means it must be set locally for the tunnel. PPTP_SERVER: Configuration--->PPTP--->PPTP Server Tick “Enable PPTP Server”, and fill in the blank textbox The modification will take effect after “Apply-->Save-->Reboot”.
Robustel GoRugged R3000 NU User Guide The modification will take effect after “Apply-->Save-->Reboot”. 4.2.4 IPsec VPN Note: The following diagrams with red color numbers mean these are the matches between server and client, and with the blue color number means it must be set locally for the tunnel. IPsecVPN_SERVER: Cisco 2811: RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Note: Polices 1,4,6,7 are default for Cisco router and do not display at the CMD. IPsecVPN_CLIENT: Configuration--->IPSec--->IPSec Basic Then click “Apply”. Configuration--->IPSec--->IPSec Tunnel Tick “Enable IPSec Tunnel1” RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide The modification will take effect after “Apply-->Save-->Reboot”. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide 4.2.5 OpenVPN Note: The following diagrams with red color numbers mean these are the matches between server and client, and with the blue color number means it must be set locally for the tunnel. OPENVPN_SERVER: Configuration--->OpenVPN--->Server Tick “Enable OpenVPN Server”. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide The modifications will take effect after click “Apply-->Save-->Reboot”. OPENVPN_CLIENT: Configuration--->OpenVPN--->Client Tick “Enable OpenVPN Client1”, and fill in the blank textbox RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide The modification will take effect after “Apply-->Save-->Reboot”. RT_UG_R3000 NU_v.1.0.0 Confidential 24.03.
Robustel GoRugged R3000 NU User Guide Chapter 5. Introductions for CLI 5.1 What’s CLI and hierarchy level Mode The R3000 NU command-line interface (CLI) is a software interface providing another way to set the parameters of equipment from the console or through a telnet network connection.
Robustel GoRugged R3000 NU User Guide R3000 NU> enable Password: ***** R3000 NU# ? //check what commands can be used in Privileged exec mode debug Debug configure information enable Turn on privileged commands exit Exit from current mode export Export file using tftp syslog Export system log import Import file using tftp load Load configure information ping Ping test reload Halt and perform a cold restart tracert Tracert test write Write running configuration tftp Copy from tftp: f
Robustel GoRugged R3000 NU User Guide 5.2 How to configure the CLI Following is a list about the description of help and the error should be encountered in the configuring program. Commands /tips Description ? Ctrl+c Invalid command “xxx” Incomplete command % Invalid input detected at '^' marker Typing a question mark “?” will show you the help information. Press these two keys at the same time, except its “copy” function but also can be used for “break” out of the setting program.
Robustel GoRugged R3000 NU User Guide Building configuration... OK R3000 NU#reload !Reboot the system?'yes'or 'no':yes //reload to take effect Example 3: Set link-management R3000 NU> enable Password: ***** R3000 NU# R3000 NU# configure R3000 NU(config)# set link-management wan link : 1.Eth0 2.Wifi ->please select mode(1-4)*1+:2 ->ICMP detection primary server[]:8.8.8.8 ->ICMP detection second server[]:8.8.8.
Robustel GoRugged R3000 NU User Guide ICMP detection retries :3 reset the interface : no ********************************************* R3000 NU # configure R3000 NU (config) # set eth0 ethernet interface type: WAN type select: 1. Static IP 2. DHCP 3. PPP0E ->please select mode (1-3) [1]: ->IP address [192.168.0.1]:58.1.1.1 ->Netmask [255.255.255.0]:255.0.0.0 ->gateway [192.168.0.254]:58.1.1.254 ->mtu value (1024-1500)[1500]: ->input primary DNS [192.168.0.254]:58.1.1.254 ->input secondary DNS [0.0.0.
Robustel GoRugged R3000 NU User Guide Set Add Set parameters Add parameters RT_UG_R3000 NU_v.1.0.0 Confidential All the function parameters are set by commands set and add, the difference is that set is for the single parameter and add is for the list parameter 24.03.
