BIGMOW User Manual USA Version Authorized Dealer: Probotics 215-886-4717 Please read this manual carefully to fully understand its content prior to using BIGMOW for the first time
This page intentionally left blank.
PAGE 3 Introduction You have decided to invest in a revolutionary piece of machinery – the Bigmow robot mower. Congratulations on choosing this high-tech equipment! We would like to thank you for the trust you have placed in our young company.
B IGMOW PAGE 4 The safety of BIGMOW B B The IGMOW automatic lawnmower has been designed from a user-safety perspective.The IGMOW automatic lawnmower is subject to a specific patent relating to the cutting blades. The blades are self-retractable on contact with objects, which is one of Bigmow’s main assets. Moreover, its sonar system allows it to detect the presence of a person or object nearby, which makes it slow down instantaneously and, on slight contact, to stop and change direction automatically.
B IGMO W PAGE 5 Table of contents 1. Introduction ..................................................................................3 2. Safety instructions and diagrams. ..................................................4 3. Description of the BIGMOW............................................................6 BIGMOW 4. Composition...................................................................................7 5. Technical Specifications. .....................................................
PAGE 6 Description of the BIGMOW The BIGMOW The Bigmow is a completely automatic lawnmower for areas up to 5 acres. By moving in an area defined by a low-voltage underground sheathed wire, it allows the owner to maintain his lawn consistently and independently. The Bigmow moves mainly at random while adapting to its environment, avoiding any obstacle through sonar and different sensors. The Bigmow will recharge its battery automatically when it reaches a minimum charge level.
BIGMOW PAGE 7 Composition 11. 2. 12. 1. 8. 4. 13. 3. 13. 13. 13. 9. 7. 19. 15. 20. 10. 11. 5. 13. 17. 14. 16. 13. 18. 6. 1.Bigmow upper 9.Protective plate (deflector) 16.Recharging station 2.Bodywork 10.Cutting blades 17.Charging socket on station 3.Bigmow underneath 11.Sonar 18.Tactile flange 4.Case containing computer 12.Front wheels 19.Contact sensor 5.Battery compartment 13.Back wheels 6.Charger socket on Bigmow 14.Bonnet 20.
B IG MO W PAGE 8 Technical Specifications. Cutting system 5 discs with 3 blades Cutting height From 0.75 in. To 3.75 in ** Cutting disk motor 3 phases, 24 Volts, 50 Watts Rotation speed 3700 RPM Back wheel motor 24 Volts, 50 Watts Maintenance capacity 5 acres, +- 20% Mowing speed 3600 sq yds. Weight 105 pounds Length 51.2 in. Height 19.7 in. Width 47.2 in. Recharging station 30 Volts AC Peripheral wire 0.
B IG MO W Mowing modes of the PAGE 9 BIGMOW Mowing modes Random Random mode is the most frequently used mode for use of the Bigmow. It consists in choosing the route to be taken at random. Every time it encounters an obstacle or the peripheral wire, the computer instructs Bigmow to move in a different direction. In this way, the route taken will never the same. Systématic. Systematic mode is more specific to certain applications and requires a uniform area with as few obstacles as possible (e.g.
B IG MO W PAGE 10 Options and spare parts for the BIGMOW When you require a spare part, it is recommended that you contact the local distributor directly. Approximately two sets of cutting blades are needed in the course of a season. It is therefore important to change the blades at the beginning of the season and then around the month of June. When the cutting blades are used on harder materials (such as branches, gravel, etc.
B IG MO W PAGE 11 Installing the peripheral wire: land boundaries It is advisable to let the local distributor install your Bigmow. He has the necessary equipment and knowledge of how to install the peripheral wire. However, it is possible for you to install it yourself by following the explanations given in this chapter. If you wish to increase your mowing area after installation, you must contact your local distributor so that he may carry out the modification(s), as only he is authorized to do.
B IG MO W PAGE 12 Installing the peripheral wire: boundaries and incline Boundaries for a long path or a lane. When the Bigmow has to pass along a long path, a lane or a narrowing in the path/lane, it is imperative that this passage be at least 13 feet wide, otherwise there is a risk that part of the lawn will not be cut when the lawn is mowed. Maximum incline of the slope The incline limit is 30% (15°).
B IGMO W PAGE 13 Installing the peripheral wire: marking boundaries Marking boundaries within the mowing area When you have large trees or a garden shed in the mowing area, it is not particularly necessary to mark boundaries for these, but depending on certain conditions, the Bigmow is able to detect them with its sonar and change direction when it comes into contact with the obstacle. No tree roots should be above ground.
B IG MO W PAGE 14 Installing the recharging station Positioning the recharging station When setting up the station, an ideal place must be found which is both close to a power supply (220VAC) and on a relatively level, steady surface, which allows at least 10 feet of peripheral wire to be placed in a straight line in front of and behind the recharging station. The power connection must be made to a circuit breaker (National Electrical Code Approved) safe for underground and outdoor use.
B IGMOW Cutting heights of the PAGE 15 BIGMOW. Adjusting the cutting height The cutting height can be adjusted between 0.75 and 3.75 inches in 12 positions. This selection is made by means of a sliding bar under the cover. To change cutting height, lift the maintenance pin (the small ball) and slide the selection bar (the large ball). Each position raises or lowers the height one quarter of an inch.
B IG MO W PAGE 16 Using BIGMOW : Recharging The Bigmow is configured in the factory with standard parameters. When the property presents certain characteristics, it is advisable for your local distributor to configure the Bigmow for your property conditions. When the peripheral wire (see “peripheral wire” section) and the recharging station (see “recharging station” section) are correctly connected, you may put the Bigmow into operation.
BIGMOW PAGE 17 Configuring the BIGMOW : Keyboard Using the keyboard. The keyboard is under the rear cover. Open the Prior to closing the cover, the user must always cover. The keyboard consists of 16 keys and press . The screen will flash for the Bigone operation key. mow to start up again. Functions.
B IG MO W PAGE 18 Configurating the BIGMOW : Menus 6. Automatic search for recharging station. 7. Starting direction for systematic mode 28.3 15H40 (towards inside or outside of mowing area) There are three sub-menus in the “Data” menu: 8. Manual Mode (for traction) • The "statistics" menu allows general data to II.The "Clock" menu * clock 25/02 be displayed on the operation of your Bigmow. allows the time and 28.3 15H40 date to be adjusted.
B IG MO W Using the BIGMOW PAGE 19 : Miscellaneous Sound and visual alerts Error Messages In the course of different functions, your Bigmow alerts you to its condition through short ‘beeps’ and/or information shown on the display. An error message is displayed on the processor window when the Bigmow encounters an unforeseen situation. The message is displayed in the form of codes, such as A00, which correspond to a particular alarm.
B IG MO W PAGE 20 Using the BIGMOW : Summary for setting parameters • « SETTINGS » MENU Setting the password • « OPTIONS » MENU BOOST mode (quick recharge) 1. « New code » Menu 1. « Options » Menu 2. O000:√ ; to change : 3. Close cover • Immediate return to recharging station 1. « Options » Menu 2. O001:√ ; to change : 3. Close cover 2. Enter code ‘’Ô_ _ _ _’’ 3. Confirm • Setting the clock 1. « Clock » Menu 2. Enter time ‘’hh:mm’’ 3.
B IG MO W PAGE 21 Using the BIGMOW : Summary for setting parameters • Demonstration Mode (does not mow) 1. « Options » Menu 1. « Options » Menu 2. O003:√ ; to change : 2. O007:- ; to change : 3. Close bonnet 3. Close bonnet • • Phase inversion 2. Silent charging (No beeps during re1. charge) 2. « Options » Menu 3. O004:√; to change : 3. Close bonnet • Systematic mowing 1. « Options » Menu 2. O005:√ ; to change : 3. Close bonnet 1.
B IG MO W PAGE 22 BIGMOW quick start in 5 steps 1. Switch the machine on with main power switch 2. Press the 3. Enter your code** (if this option has been selected) : 4. Press 5. Press the ‘ 6. Close the cover and your BIGMOW sets off automatically. ‘ ’ button on the keyboard ‘ ‘+CODE (e.g.’* 1234’) ‘ ’ to confirm the code* ’ button on the keyboard (the screen then flashes) *To be done beforehand (during first use of Bigmow), prior to closing the cover: 1.
PAGE 23 B IGMOW Maintenance of the BIGMOW. Maintenance of the Bigmow is important. Regular checks can improve the day-to-day quality of mowing. You may wish to refer to the maintenance summary sheet for further help. Cutting blades The blades are the principal elements that give a good result. It is advisable to check them at least once a month and the replace them when they are broken. For one season, the user must have two sets of blades (15 pieces per set).
B IG MO W PAGE 24 Maintenance of the BIGMOW. Batteries Batteries During winter The batteries have a certain functional capacity. At the end of the mowing season, recharge your In automatic mowing mode, your Bigmow returns Bigmow and place it in a sheltered, dry place. to the recharging station at the moment when the It is advisable to have the machine serviced durbatteries reach a set charge.
B IGMO W PAGE 25 Problems 1 The machine operates in reverse Situation Solution 1 Bonnet position connectors clogged up 1 Clean between the connectors and chassis 2 Protective flange connector in contact 1 Press along full length of flange from top to bottom to disconnect 2 Remove flange connector and test without the connector. If the problem persists, it is being caused elsewhere in the machine.
PAGE 26 Notes : FR040824 B IGMOW
Your Distributor SofTee Manufacturing, LLC 3163 Wexford Way Southport, NC 28461 Your Local Dealer Date of Purchase : _ _ / _ _ / 200...
