Specifications

ManualsBrandsRobotics Technologies ManualsMusical equipmentmicroBus-Cam II

microBus-Cam II

Installation and Operation Manual

Thank you for choosing the microBus-Cam II®. This combination of a digital recorder,

camera and microphone into one package is a breakthrough in size, cost and convenience.

Totally solid-state, with no moving parts, the microBus-Cam II® records to an SD (secure

digital) memory card for ultimate reliability in all weather and road conditions.

This manual provides a source for easy navigation and setup of the product features and

operation. Here, you can set:

• On-screen and recorded Time and Date stamps.

• Recording quality.

• Recording speed.

• Recording schedule.

• Whether to overwrite or stop recording when memory is full.

Please refer to the individual sections for complete details on each phase of use.

Summary of content (23 pages)

PAGE 1
microBus-Cam II Installation and Operation Manual Thank you for choosing the microBus-Cam II®. This combination of a digital recorder, camera and microphone into one package is a breakthrough in size, cost and convenience. Totally solid-state, with no moving parts, the microBus-Cam II® records to an SD (secure digital) memory card for ultimate reliability in all weather and road conditions. This manual provides a source for easy navigation and setup of the product features and operation.
PAGE 2
microBus-Cam II Table of Contents 1.0 Mechanical Installation............................................................................................................. 3 2.0 Product Features...................................................................................................................... 4 2.1 Status LEDs.......................................................................................................................................... 5 3.0 Electrical Connections..............
PAGE 3
microBus-Cam II 1.0 Mechanical Installation 1. Mount the support bracket to the bulkhead or ceiling of the vehicle, using the sheet-metal screws (provided). Position the bracket at the horizontal center of the vehicle. If the bracket is to be bulkhead-mounted, then position the bracket as high as possible on the bulkhead. If the bracket is being mounted to the ceiling, then mount the bracket as far forward as possible. These mounting practices will provide optimal sight-lines. 2.
PAGE 4
microBus-Cam II 2.0 Product Features Mic Camera Lock A/V Jack Status LEDs Remote Sensor SD Card Cover 4. To access the SD Card Socket: 1. Unscrew Lock, using the key 2. Pivot the cover open 3.
PAGE 5
microBus-Cam II 2.
PAGE 6
microBus-Cam II 3.0 Electrical Connections Access the Power Connector from the Rear of the Unit Connect each wire as indicated by the diagram. Make sure that the battery connection is to a constant source of +12 VDC power, and fuse the +12 VDC wire at a maximum of 2A. That's it! You're done with the installation. Finally, plug the AV Adaptor (provided) into the A/V jack that is located below the camera.
PAGE 7
microBus-Cam II 4.
PAGE 8
microBus-Cam II 5.0 Screen Layouts 5.1 Standby (Live) Mode 5.
PAGE 9
microBus-Cam II 6.
PAGE 10
microBus-Cam II 10
PAGE 11
microBus-Cam II 7.0 Recording Setup 7.
PAGE 12
microBus-Cam II 12
PAGE 13
microBus-Cam II 13
PAGE 14
microBus-Cam II 8.0 Continuous Record Mode (Rewrite) 9.
PAGE 15
microBus-Cam II 10.
PAGE 16
microBus-Cam II 16
PAGE 17
microBus-Cam II 11.0 Recording Mode NOTE: Use only Manual and Scheduled Settings for Vehicles.
PAGE 18
microBus-Cam II 12.
PAGE 19
microBus-Cam II 13.
PAGE 20
microBus-Cam II Note: The GPS function is reserved for future versions. Use the TIME selection to enable/disable the display and recording of the time-stamp. The ENABLE setting is highly recommended. When you have finished programming, press MENU to save and exit to LIVE MODE. When the Ignition is activated, the unit will start recording with your new settings.
PAGE 21
microBus-Cam II 14.0 Working with Clips--The SD Card The recorded video clips are stored on a totally solid-state SD (Secure Digital) Card. The microBus-Cam II® can accept SD Cards with capacities up to 32 GB. Most users prefer to use a computer to view their clips. It is more convenient than onvehicle viewing— just remove the card and plug it into the SD Card reader on your computer.
PAGE 22
microBus-Cam II 15.0 Post Trip Delay This feature provides the ability to continue recording for a set period--even after the Ignition (or other trigger source) is turned off. The time delay setting can be made with the 3-position DIP switch that is located on the rear of the unit. Simply use a small screwdriver or pen to slide the small switches into the OFF or ON positions. We have provided a table of time delays (in minutes) and the switch settings that correspond to those delays (see below).
PAGE 23
microBus-Cam II 16.0 Specifications & Features For DVR Parameter Compression Standard MPEG-4 / H.264 Resolution Full D1 (704 x 576) Video Format MPEG-4/ASF Audio Format / Rate, Encoding MP3 / 8KHz,ADPCM Frame Rate User-selectable, 5/15/30 Storage Medium SDHC Memory Card, Max.