ROBOT MOWER USER MANUAL Please read this manual before Please keep this manual for use future reference ROHS
CONTENTS The products are manufactured by Taizhou Tianchen Intelligence & Electrics Co., Ltd. www.tianchen-cn.com Thank you for purchasing our product. We know that you will enjoy the extra free time you will have while using our robot lawn mower to mow your lawn. You will be impressed with your lawn's appearance and vest of all, robot lawn mower did it for you. IMPORTANT! The following pages contain important safety and operating instructions. Please read and follow and instructions in this manual.
1.INTRODUCTION AND SAFETY 1. Introduction and safety 1.INTRODUCTION AND SAFETY 1.2 Symbols on mower These symbols can be found in the mower. Study them carefully so you understand their significance. 1.1 Introduction Product, product specifications and this document are subject to change without notice. All other trademarks are property of their respective owners. 1. The symbol is pasted on the top of mower, please read it carefully before using the appliance.
1.INTRODUCTION AND SAFETY 1.INTRODUCTION AND SAFETY 1.4 Safety instructions 3. Charging station symbol. - Read the owners/operation manual carefully and follow all the safety and warning instructions. This label is pasted on charging station, please make sure to position this side towards lawn interior. Failure to do may result in damage to property or persons.
2. PRESENTATION 1.INTRODUCTION AND SAFETY - Use heavy gloves when inspecting or servicing the blades. 2. Presentation - Wear eye protection and use gloves when installing the virtual wire and driving the wire stakes/pegs. Firmly drive all pegs in order to keep the wire from becoming a tripping hazard. This chapter contains information you should be aware of when planning the instalation. 2.1 What's in box - Do not use the charging station power supply with an extension cord.
2. PRESENTATION 1 Handle: 2 Bumper: 16 Charging light Red: charging To change a new direction when it Green: fully charged or idle bump obstacles. 17 Charge terminal 3 Charging point 18 Virtual wire terminal Connect the virtual wire randomly. 4 Emergency switch: there is no positive and negative. Press it at any time, the mower 19 Charging sheet turn off at once. 20 Guide channel 5 Charging terminal: Connect with charger for recharge 21 Stakes hole directly.
2. PRESENTATION 2. PRESENTATION - Cutting width:28cm 2.3 Technical data - Auto recharge system When the mower is operating it feels powerless, the cutting motor turn off at once and it will find the virtual wire then go alone it back to charging station for recharge automatically. (this allows you to keep the charger connected with the charging station all the time, even after the battery is fully charged.) On auto pattern, the mower will go on mowing after fully recharge.
2. PRESENTATION 2. PRESENTATION 2.4 Working route Model Battery 10900 Type of battery battery Lead-acid battery Lithium battery 7.2Ah 7.2Ah Charging time 3-4hours 4.5hours Average working time 2-3hours 2-3hours 11000 IMPORTANT INFORMATION Functions: X Around virtual wire walking option Manual pattern Mower's running path by user's willingness. X User turn on the mower and select Manual pattern, The mower will not going to find the virtual wire .
3. INSTALLATION 3. Installation This chapter describes how you install this mower. Before starting the installation read the previous chapter 2. Presentation. Read the whole of this chapter too before starting the installation. How the installation is made also affects how well the mower will work. It is therefore important to plan the installation carefully. 3.1 Preparations Training - Read the instructions carefully. Be familiar with the controls and the proper use of the appliance.
3. INSTALLATION 3. INSTALLATION 3.3 Charging station installation - Choose best installation place, please make sure which is flat, no water, no magnetic interference and no obstacle in the front of charging station. - Lay virtual wire in the middle of charging station. Virtual wire Peg - Fix the charging station with four stakes. Charging station best install place: 1. Make sure it 2. No magnetic interference 3. No water 4.
3. INSTALLATION 3.4 Virtual wire installation The virtual wire can be installed in one of the following ways: - Securing the wire to the ground with pegs. It is preferable to staple down the virtual wire, if you want to make adjustments to the virtual wire during the first few weeks of operation. - Bury the wire It is preferable to bury the virtual wire if you want to dethatch or aerate the lawn. 3. INSTALLATION - A minimum distances of front charging station and obstacle is 2 meters.
3. INSTALLATION 3. INSTALLATION - If a high obstacle, for example a wall or fence, borders the working area, the virtual wire should be laid at least 35cm from the obstacle. This will prevent mower from colliding with the obstacle and reduce body wear. Greater than 35cm - The wires leading to the island and returning from it should be parallel and touding. But do not cross them! If protected obstacles are grouped closely together demarcate them by a single.
3. INSTALLATION 3. INSTALLATION - How to set virtual wire on the ground which has swimming pool. Distance between two wire: 1m - Care must be taken not to create a corner sharper shorter than 90 degrees when setting up virtual wire. A corner sharper less than 90 degrees can cause the mower to lose track of virtual wire. We can make greater than 90 degrees corner like follow picture shows.
3. INSTALLATION 4. REMOTE CONTROL 4.1 Remote control 3.5 Virtual wire and charging station connecting 1 To stop the mower. Press it, the 1 mower enters taskstate. 9 2 Indicator light. - Connect two ends of virtual wire to patch jack (virtual wire terminal located on charging station) randomly, there is no positive and negative. - Redundant virtual wire must be cut. 2 3 Go right. 4 Press it during mower is working, it goes back to charging station. 3 8 5 Effected while mower in taskstate.
5. USE 5. Use IMPORTANT INFORMATION Operation with Auto Pattern - Do not leave the machine to operate unattended if you know that there are pets, children or people in the vicinity Operation with Manual Pattern - Mow only in daylight or in good artificial light. - Avoid operating the appliance in wet grass. - Do not operate the appliance when barefoot or wearing open sandals. - Always wear substantial footwear and long trousers. - Always be sure of your footing on slopes.
5. USE 5. USE 5.3 Stopping mower /Turn off mower Steps as follow: 1. Press power button from remote control . Mower stops, the blade motor stops. mower goes into taskstate. 1. Turn off the mower by key. 2. The appliance also can be turned off by press emergency switch directly. 3. Turn off the mower by anti-clockwise the key switch. 2. Insert charger and screw the Knob. 3. Connect the charger to power supplier. 5.4 Emergency Switch Press emergency switch at any time the mower power off at once.
6. MAINTENANCE AND STORAGE 6. MAINTENANCE AND STORAGE 6. Maintenance and storage - During maintenance operations, use the individual protections indicated by the Manufacturer , especially when intervening on the blade. - Before performing maintenance operations, make sure that the robot has stopped in safety conditions.
6. MAINTENANCE AND STORAGE 14. In the event leakage of electrolyte flush with water/neutralising agent, seek medical help if it comes into contact with the eyes etc. 15. Servicing of the appliance should be according to manufacturers instructions. This product (include battery pack)must be disposed of at a designated collection pint for electrical and electronic waste. For more information, contact your local city office or the shop where you purchased the product. 6. MAINTENANCE AND STORAGE 6.
7. TROUBLE SHOOTING 7. TROUBLE SHOOTING 7. Trouble shooting Problem After turn on the mower by key and set operate patten, but the mower still can not start. And the charging station is beeping. Problem Possible reasons 1. The virtual wire fails to send signals. 2. The virtual is broken Possible reasons Solutions 1.Check the virtual wire light (colorless). Be sure the virtual wire is connected to the charging station that is motion, and there is no loose place. Mower stop working and beeping. 1.
7. TROUBLE SHOOTING Problem The batteries can not recharged Possible reasons Power nearing natural end of life 7. TROUBLE SHOOTING Solutions 1. Send the mower to service station and replace the battery 2. Check whether the charger is well connected. Grass is extremely overgrown or very wet Cut the grass appropriate height. Terrain needs landscaping repairs. Fill in all holes, cover or exclude all exposed roots in order to smooth the terrain. Mower does not complete the edge.
8. EXPLODED VIEW 7. TROUBLE SHOOTING Problem The robot is very noisy Possible reasons Solutions 1. Damaged cutting blades 1. Replace the blade with a new one. 2. Cutting blade flooded by residues(tapes, ropes, plastic fragments, etc) 2. Stop the robot in safety conditions; use protection gloves to avoid the risk of cuts on hands; remove the fold cause from the blade. 8.1 Charging Station Exploded View 1 2 3.
8. EXPLODED VIEW 8.