Specifications

20
- Remove the bell from the foot, then remove the
blades. Be careful to avoid damaging the surface
of the blade shaft and the watertight seals. Do not
use too strong a detergent when cleaning the parts.
- Ensure that all the different parts are thoroughly
dried before reassembly.
• BLADES
The blades can be removed from the bell for
thorough cleaning.
Always dry the blades thoroughly after cleaning to
avoid spotting.
• WHISK HOLDER
Never immerse the whisk holder in water. Clean it
with a slightly damp cloth or sponge.
Never clean the whisk holder in a dishwasher.
• WHISKS
The whisks can be cleaned either by hand or in a
dishwasher.
To ensure effective cleaning, we advice you to
remove the whisk ejector.
You are also advised to change, at the same time,
the washer and the watertight seals.
• WHISKS
The success of your preparation will depend essen-
tially on the state of the metal wires and their
amount of wear and tear. They should therefore be
replaced from time to time in order to ensure opti-
mum quality of the finished product.
• FOOT SEAL
In order to maintain a perfect watertight seal
between the foot and the bell it is necessary to
check the wear of the seal regularly and replace it if
necessary.
•WASHER
The washer can be greased using a suitable food
safe lubricant.
In order to maintain a perfect watertightness it is
necessary to check the wear of the washer, and if
necessary, to replace it.
TECHNICAL
SPECIFICATIONS
• WEIGHT
Net weight Gross weight
CMP 250 V.V. 3,0 kg 4,7 kg
CMP 300 V.V. 3,1 kg 4,8 kg
CMP 350 V.V. 3,3 kg 5,0 kg
CMP 250 Combi
with mixer 3,1 kg
6,6 kg
with whisk 3,4 kg
CMP 300 Combi
with mixer 3,2 kg
6,7 kg
with whisk 3,4 kg
• DIMENSIONS (en mm)
Check that your detergent is suitable for cleaning
plastic parts. Some washing agents are too alka-
line (e.g. high levels of caustic soda or ammonia)
and totally incompatible with certain types of
plastic, causing them to deteriorate rapidly.
IMPORTANT
MAINTENANCE
• BLADES
The performance of the cut essentially depends on
the state of your blades and their wear. The blades
are subject to wear and as such need to be replaced
from time to time to ensure the consistent quality of
the end product.
•WORKING HEIGHT
We recommend that you ensure that the container is
placed on a stable and solid work surface.
•NOISE LEVEL
The equivalent continuous sound level when the foot
is not immersed in anything is less than 70 dB (A).
• ELECTRICAL DATA
Single-phase machine
CMP 250 V.V. / CMP 250 Combi
Mixer Whisk
Motor Speed Speed
Power Intensity
(rpm) (rpm)
(Watts) (Amp.)
230 V/50 Hz 2300 to 9600 500 to 1800 270 1.1
120 V/60 Hz 2300 to 9600 500 to 1800 240 2.0
220 V/60 Hz 2300 to 9600 500 to 1800 230 1.0
A = 094
B = 610
C = 090
D = 255
E
A
B
FC
CMP 250 V.V.
A = 094
B = 660
C = 090
D = 305
CMP 300 V.V.
A = 094
B = 718
C = 090
D = 363
CMP 350 V.V.
A = 094
B = 640
C = 090
D = 300
E = 390
F = 120
CMP 250 Combi
A = 094
B = 700
C = 090
D = 350
E = 390
F = 120
CMP 300 Combi