Specifications

21
The blades are sharp tools, handle them with
care.
W ARNING
Never try to override the locking and safety
mechanisms.
Never insert an object into the preparation.
Never switch the appliance on unless it has been
placed in the preparation bowl.
Before dismantling the foot and bell, always check
that the power mixer is unplugged.
We recommend that you tilt the power mixer at
a slight angle to prevent the bell from touching
the bottom of the container.
REMINDER
Single-phase machine
CMP 300 V.V. / CMP 300 Combi
Single-phase machine CMP 350 V.V.
Power Intensity
Motor
Mixer Speed
(Amp.)
(rpm)
(Watts)
230 V/50 Hz 2300 to 9600 350 1.6
120 V/60 Hz 2300 to 9600 320 2.9
220 V/60 Hz 2300 to 9600 290 1.4
Mixer Whisk
Motor Speed Speed
Power Intensity
(rpm) (rpm)
(Watts) (Amp.)
230 V/50 Hz 2300 to 9600 500 to 1800 300 1.4
120 V/60 Hz 2300 to 9600 500 to 1800 280 2.6
220 V/60 Hz 2300 to 9600 500 to 1800 270 1.3
SAFETY
ROBOT-COUPE power mixers are equipped with
a safety system comprising of a :
- safety control button
- safeties on motor: thermal and overload protection
-no volt release safety.
• Safety control button
This safety mechanism prevents any unintentional
starting of the power mixer. In fact, it is necessary to
press down two buttons to start the power mixer. In
order to start the machine, read the paragraph en-
titled OPERATING THE APPLIANCE (page 16).
• Thermal and overload protection
If there is an obstruction in the container (a spoon
or utensil) or the machine is exposed to over use /
overload, the thermal safety mechanism automati-
cally stop the motor. In this case, wait for the power
mixer to cool down completely before restarting,
see paragraph entitled OPERATING THE
APPLIANCE (page 16).
•No volt release a supply failure
In the event of a power cut or after the machine has
been unplugged, the power mixer will not restart by
itself. It is necessary to follow the steps in the
paragraph entitled OPERATING THE APPLIANCE
(page 16).
PROBLEMS
At first, try to identify precisely what has caused the
power mixer to stop.
• If it is due to a powercut if the appliance has
been unplugged
- Release the control button (CB).
- Check the power supply.
- Restart the power mixer following the paragraph
entitled OPERATING THE APPLIANCE (page 16).
• If it is due to overheating of the machine
- Release the control button (CB).
- Unplug the power mixer.
-Wait a few minutes for the motor to cool down
and the thermal safety mechanism to be reset.
- Restart the power mixer following the paragraph
entitled OPERATING THE APPLIANCE (page 16).
• If you cannot locate the cause of the problem
- Release the control button (CB).- Unplug the
power mixer.
-Check :
- the plug
- that the blades are free to rotate in the bell,
- the state of the power cord,
- that the drive shaft is free to rotate. To do this,
remove the bell and test the rotation of the end of
the drive shaft manually.
STANDARDS
MACHINES IN COMPLIANCE WITH:
• The following European directives and related
national legislation:
- Modified "machinery" directive 98/37/EEC,
- "Low voltage" directive 73/23/EEC,
- "EMC" directive 89/336/EEC,
- "Materials and parts in food contact" directive
89/109/EEC,
- "Plastic materials and parts in food contact"
directive 90/128/EEC.
• The following European harmonized standards
and standards setting out health and safety rules:
• We certify that the Mini MP 170 V.V. and Mini
MP 220 V.V. comply with the essential require-
ments of the standard EN 292 – 1 and 2: ma-
chine safety – general design principles
- EN 60204 -1 (1992),