CMP 250 V.V. • CMP 300 V.V. • CMP 350 V.V.
SUMMARY WARRANTY IMPORTANT WARNING INTRODUCTION TO YOUR NEW POWER MIXER SWITCHING ON THE APPLIANCE • Advice on electrical connections OPERATING THE APPLIANCE • Starting and stopping the power mixer • Continuous operation • Variable-speed operation WORKING POSITION • Blade function • Whisk function ASSEMBLING / DISMANTLING CLEANING • Motor unit • Foot and bell • Blades • Whisk holder • Whisks MAINTENANCE • Blades • Whisks • Foot seal • Seal ring TECHNICAL SPECIFICATIONS • Weight • Dimensions • Working
ROBOT-COUPE S.N.C., LIMITED WARRANTY 2 - Labour to sharpen and/ or replacements for Your new ROBOT-COUPE appliance is warranted to the original buyer for a period of one year from the date of sale if you bought it from ROBOT-COUPE S.N.C. If you bought your ROBOT-COUPE product from a distributor your product is covered by your distributor’s warranty (Please check with your distributor terms and conditions of the warranty). The ROBOT-COUPE S.N.C.
IMPORTANT WARNING W A R N I N G KEEP THESE INSTRUCTIONS IN A SAFE PLACE WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your appliance and enable you to use the equipment correctly.
INTRODUCTION TO YOUR NEW POWER MIXER Robot-Coupe has developed a whole range of power mixer. Their technical characteristics are shown in the table below. Models Speed variation Mixer attachment Whisk capacity attachment Litres CMP 250 V.V. • 250 mm 15 CMP 300 V.V. • 300 mm 30 CMP 350 V.V. • 350 mm 45 CMP 250 Combi • 250 mm 220 mm 15 CMP 300 Combi • 300 mm 220 mm 30 These models are working tools that are perfectly suited to the needs of their users.
Whisk function : speed between 500 and 1800 rpm. • WHISK FUNCTION Mixer function : speed between 2300 and 9600 rpm. You can also hold the appliance by the handle with one hand, leaving the other hand free to hold the bowl, if necessary. While you process the preparation, we recommend that you move the whisks around in the bowl, in order to ensure that the mixture is completely homogeneous. We strongly advise you to keep the whisks from touching the sides of the bowl.
- Insert the conical part C into the bell. With the washer touching the tube seal D , turn the bell in the direction of the arrow (see above figure) to lock the bell lug E and tube lug F together moderately tightly. BLADE LOCKING Removing the casing BLADES WITH WATERTIGHT SEALS - Check that the machine is not plugged in. - Turn the whisk holder in the opposite direction to that used when attaching it. - When it will go no further, remove the whisk holder from the aluminium casing.
- As you push the whisk into the whisk holder drive shaft C , rotate it slightly in order to slot the drive lugs into the notches D of the drive shaft C , thereby locking the whisk into place inside the shaft. - To check that the whisk is properly fixed inside the shaft C , gently tug the metal wires. - Repeat this procedure with the second whisk. If you cannot push it in properly, remove it, rotate it 90° and start again.
- Remove the bell from the foot, then remove the blades. Be careful to avoid damaging the surface of the blade shaft and the watertight seals. Do not use too strong a detergent when cleaning the parts. - Ensure that all the different parts are thoroughly dried before reassembly. • BLADES The blades can be removed from the bell for thorough cleaning. Always dry the blades thoroughly after cleaning to avoid spotting. • WHISK HOLDER Never immerse the whisk holder in water.
Single-phase machine CMP 300 V.V. / CMP 300 Combi • Thermal and overload protection Motor Mixer Speed (rpm) Whisk Speed (rpm) Power (Watts) Intensity (Amp.) 230 V/50 Hz 2300 to 9600 500 to 1800 300 1.4 120 V/60 Hz 2300 to 9600 500 to 1800 280 2.6 220 V/60 Hz 2300 to 9600 500 to 1800 270 1.3 Single-phase machine CMP 350 V.V. Motor Mixer Speed (rpm) Power (Watts) Intensity (Amp.) 230 V/50 Hz 2300 to 9600 350 1.6 120 V/60 Hz 2300 to 9600 320 2.
74
75
77
78
79
81
82
83
85
86
87
89
90
91
93
95
MADE IN FRANCE BY ROBOT-COUPE S.N.C. Export Department Tel. : + 33 1 43 98 88 33 - Fax : + 33 1 43 74 36 26 18, rue Clément Viénot - BP 157 94305 Vincennes Cedex - France http://www.robot-coupe.com - email : international@robot-coupe.com We reserve the right to alter at any time without notice the technical specifications of this appliance. © All rights reserved for all countries by: ROBOT-COUPE S.N.C. Réf. 450 093 - 09/2003 - CMP 250 V.V. • CMP 300 V.V. • CMP 350 V.V.
