Roborock Robot Vacuum Cleaner S5 Max User Manual Read this user manual carefully before using this product and store it properly for future reference.
Welcome Thank you for choosing a Roborock Robot Vacuum Cleaner. Treat yourself to crisp, just-mopped floors every day with S� Max. Engineered for a seamless automated mopping, it has a super-sized water tank, precision water control, virtual no-mop zones, and more. Combined with precision laser mapping, advanced navigation, and intense vacuum suction, it makes spotless floors easier than ever. All you need to do is set it and get on with living.
Product introduction Robot On/Off ·Press to start cleaning ·Press and hold to power on or off Power indicator ·White: Battery level ≥ ��% ·Red: Battery level < ��% ·Flashing: Charging or starting up ·Flashing red: Error Dock/Spot Clean ·Press to return to the dock ·Press and hold to spot clean Note: Press any button to pause cleaning, returning to dock, or spot cleaning.
Product introduction Parts list Charging dock Moisture-proof mat Mop cloth mount Power cable Mop cloth ��
Product introduction Dustbin Robot Dustbin cover Dustbin latch WiFi indicator light ·Off: WiFi disabled ·Slow flashing: Waiting for connection ·Fast flashing: Connecting ·Steady: WiFi connected Air filter System reset Air vent Water tank latch Speaker ��
Product introduction Machine and sensors Wall sensor Recharge sensor Cliff sensor Omnidirectional wheel Bumper Charging contact Laser distance sensor Side brush Main wheels Main brush cover latch Main brush ��
Product introduction Mopping module Mop cloth attachment slot Water tank stopper Mop cloth bracket Water filter Mop cloth bracket clip Water tank Mop cloth Water tank latch Attaching area Charging dock Charging dock power indicator Signal transmitting area Power socket Charging points Charging points ��
Installation Using the robot �. Place the charging dock against the wall on a flat surface and plug it into the mains power. �. Secure the charging dock with the adhesive tape. Wipe the floor of the area where the charging dock will be placed with a dry cloth, then stick the enclosed double-sided tape to the floor. Place the dock onto the double-sided tape to secure it in place. Double-sided tape More than �.�m (�.�ft) More than �.�m (�ft) More than �.�m (�.
Installation Using the robot �. Secure the moisture-proof mat. After securing the charging dock, wipe the area where the moisture-proof mat will be placed with a dry cloth as shown. Stick the double-sided tape first to the moisture-proof mat then in position on the floor. �. Power on and charge. Press and hold the button to turn on the robot. When the power indicator lights up, place the robot onto the charging dock to begin charging. The robot uses a high-performance lithium-ion rechargeable battery.
Installation ➂ Add device Open the app and click "+" in the top right corner, then follow the instructions in-app. Once your robot has been added, it will be found in a list on the homepage. Connect to the app 5.Connect to the app.(recommended) ➀Download the Roborock app or Xiaomi home app a. Search "Roborock" in the App Store or Google Play, Or scan the QR code below, then download and install the app.
Installation Using the robot �. Mopping Note: It is recommended that all floors are vacuumed at least three times before the first mopping session to reduce excessive dirt buildup on the mop. � � Remove the water tank Press down the water tank latch and slide the tank backwards to remove it. � � Fill the water tank Open the water tank, fill it with water, and close it tightly. Note: ·To prevent corrosion or damage, do not use cleaning fluid or disinfectant in the water tank.
Installation Using the robot � Attach the mop cloth bracket Slide the mop cloth bracket under the water tank following the alignment marks, until you hear a click. �. Remove the mop cloth bracket To remove the mop cloth bracket, press the two clips inwards and pull the bracket backwards. Note: Cleaning the mop cloth after ��-minutes of mopping is recommended to ensure water flow and cleaning quality.
Installation On/Off Press and hold the button to turn on the robot. The power indicator will turn on and the robot will enter Standby mode. If the robot is in Sleep mode, press and hold the button to turn it off and end the current cleanup. Note: ·Cleaning cannot start if the battery level is too low. Allow the robot to charge before restarting cleanup.
Instructions for use Charging Spot Cleaning Auto: After cleaning, the robot will automatically return to the charging dock to recharge. Manual: In Pause mode, press the button to send the robot back to the charging dock. The power indicator will flash slowly as the robot charges. In the Standby or Pause mode, press and hold the button to start spot cleaning. This mode is used to clean a �.�m x �.�m square area centered on the robot. After cleanup, the robot will return to the center of the square.
Instructions for use Selective Room Cleaning Pin n Go Use the APP to set a destination for the robot to go to. Select specific rooms for cleaning in the APP. In this mode, the robot will only clean the selected rooms. C A Cleaning mode Use the APP to choose from Quiet, Balanced, Strong, or MAX modes. Balanced mode is the default. D Do Not Disturb (DND) mode B In DND mode, no cleanups will start, no voice alerts will play, and the power indicator will dim.
Instructions for use More app functions No-go zones / Invisible Wall / Mopping No-Go Zone The app can be used to draw Virtual No-Go Zones and Walls, as well as Virtual No-Mop Zones and Walls to keep the robot from entering the areas you define. Virtual No-Mop Zones and Walls are only activated when the mopping cloth bracket is installed.
Instructions for use Routine maintenance Charging dock Main brush * Clean weekly The charging dock should be plugged in and placed against a wall on level ground, with more than �.�m (�.�ft) of clearance on each side, and more than �.�m (�ft) in front. For the best experience when using the mobile app, place the charging dock in an area with strong WiFi coverage. �. Turn the robot over then unlatch and remove the main brush cover. �. Take out the main brush, remove and clean its bearings. �.
Routine maintenance Using the main brush cleaning tool Use the main brush cleaning tool to remove any hair entangled around the main brush. �. Open the dustbin lid as indicated by the arrow and pour out the contents. Note: If there is a large amount of hair, or hair is tightly entangled, remove it carefully to avoid damage to the main brush. Clean the washable filter Dustbin and filter * Clean every two weeks * Weekly cleaning is recommended �.
Routine maintenance Clean the washable filter * Clean every two weeks �. Rinse repeatedly and tap the filter frame to remove as much dirt as possible. �. Fill the dustbin with clean water and close the cover. Gently shake the dustbin, then pour out the dirty water. �. Leave the filter to dry before reinstalling it. Note: Allow the filter to dry thoroughly before use. ��-hours of drying is recommended. Note: Only use fresh water without cleaning liquid. Battery �. Remove the filter and clean it with water.
Routine maintenance Side brush Mop cloth * Clean after use * Monthly cleaning recommended �. Turn the robot over and remove the screw holding the side brush. �. Remove and clean the side brush. �. Reinstall the side brush and tighten the screw. �. Remove the mop cloth from the mop cloth bracket. �. Clean the mop cloth and dry it. Note: ·If the mop cloth gets excessively dirty, cleaning quality will be affected. Cleaning it before use is recommended.
Routine maintenance Omnidirectional wheel Machine sensors * Frequent cleaning is recommended * Monthly cleaning recommended �. Turn the robot over. �. Use a small screwdriver to separate the axle and the tire. �. Rinse the axle and tire with water to remove any hair and dirt. �. Dry and rebuild the wheel, then press it back in place. Use a soft dry cloth to wipe and clean all sensors, including: �. Four cliff sensors at the bottom of the robot. �. The wall sensor on the right of the robot. �.
Routine maintenance Holiday Energy Saving Function When the robot is docked, press and hold "Recharge" for �� seconds or until you hear an alert sound. This will activate Holiday mode. In this mode the robot will switch to Low Power mode to minimize power consumption. This includes a dimming of the LED indicator, and the stopping of all non-charging related functions including cleaning, remote control over WiFi, and more.
Troubleshooting If an error occurs during cleanup, the power indicator will flash red quickly, and a voice alert will play. Refer to the table below for resolution options. Error Solution Error �: Clean and lightly tap the bumper. The bumper is stuck. Tap the bumper repeatedly to dislodge any jammed items. If nothing falls out, move the robot to a new location and restart. Error �: Rotate the laser head to check that it turns freely. Error �: Move the robot to a new location and restart.
Troubleshooting If an error occurs during cleanup, the power indicator will flash red quickly, and a voice alert will play. Refer to the table below for resolution options. Error Solution Error ��: The battery is too low. Recharge before use. Low battery. Recharge before use. Error ��: High-intensity magnetic field detected. Move the robot away from the magnetic tape and restart. Error ��: Charging error. Clean the charging contact area. Error ��: Battery error.
FAQs Problem Unable to power on Unable to charge Slow charging Unable to recharge Abnormal behavior Noise during cleaning Poor cleaning ability or dust falling out Unable to connect to WiFi Solution The battery level is low. Put the robot on the charging dock to charge it before use. The battery temperature is too low or too high. Only use the robot within the range of �-��°C (��-���°F). If the charging dock is not receiving power, check that both ends of the power cable are properly connected.
FAQs Problem Solution Scheduled cleaning is not working The battery level is too low. Scheduled cleaning can only begin when the battery level is above ��%. Please confirm whether the timed cleaning setting is set to“effective once”? Is power always being drawn when the robot is on the charging dock? The robot will draw power while it is docked to maintain battery performance, but power consumption is extremely low.
Robot Vacuum Cleaner Manufacturer: Beijing Roborock Technology Co.,Ltd. Product Model: roborock S� Max Address of Manufacturer: Floor �, Suite ����, ����, ����, Building C, Kangjian Baosheng Plaza, No.� Heiquan Road, Haidian District, Bejing, P.R.CHINA For more product information, visit our website: www.roborock.com For after-sales support, email our after-sales service team: US/Non-Europe Support: support@roborock.com Europe Support: support@roborock-eu.