USER GUIDE Original user instructions Robotic Mower RK1000, RK1000 Pro, RK2000, RK2000 Pro, RK3000 Pro, RK4000 Pro
Safety First IMPORTANT! READ THESE INSTRUCTIONS AND SAFETY GUIDE CAREFULLY BEFORE USE. RETAIN FOR FUTURE REFERENCE 1 2 3 Safe Operating Practices Symbol Definitions Safety Features Annex A – Battery removal instructions This product is an autonomous robotic mower, powered by a rechargeable lithium-ion battery and includes a base station. The mower will independently depart from the base station, mow the lawn and return to the base station for charging.
in terms of Directives 2006/42/EC and 2014/53/EU. It may describe models that are not available in your country. Please note the terminology below when using this guide. Front and rear of the mower: The front is the opposite side to the (red) STOP button. It is the direction of travel of the mower and where the passive wheel/s are located. The rear is where the (red) STOP button is located, and where the traction drive wheels are located.
Important Safety Information WARNING It is your responsibility to: • Restrict the use of this mower to persons who have read, understood and follow the warnings and instructions in this guide and in the mower • Inform your neighbours that you have a robot mower in operation and that they may be injured if they access your lawn during operation DANGER Always connect the power supply to the indoor, weather-protected power supply circuit protected by a residual current device (RCD) with a tripping current of
Operating 1 Safe Practices A. General Information 1. 2. 3. 4. 5. 6. 7. 8. Read, understand and follow all instructions on the mower and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. Familiarise yourself with all controls and their proper operation.
C. Operation WARNING Do not allow the mower to operate unattended if you know that there are or may be pets, children or people in the vicinity. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Your robotic mower is a dangerous power tool. Exercise care when operating it and follow all safety instructions and warnings. In the event of an accident or malfunction during operation, press the red STOP control immediately.
If the power supply is installed outdoors, do not operate or disconnect it when the temperature falls below 0°C or rises above 40°C to avoid the risk of fire. 19. Steer the mower manually only when it is within your range of vision. Stay within 6 metres of the mower when you are operating it manually. 20. Do not overreach, keep the balance at all times and always be sure of footing on slopes; always walk, never run while operating the machine. D. Children 1. 2. 3. 4. 5. 6.
F. Remote Operation 1. 2. 3. 4. 5. 6. Refer to the separate operator’s manual provided with the downloadable app. Follow all warnings and instructions provided. Always operate the mower according to the app instructions while standing away from the mower. Keep a safe distance between you and the mower when it is in operation. Always stop mower operation before approaching it for any reason. Exercise extreme caution when the mower is moving towards you.
H. Slope Operation 1. 2. 3. 4. 5. All slopes require extra caution. If you feel that the mower cannot maintain traction on a slope, the slope is too steep to mow. Wet grass will decrease traction and may cause the mower to slip and slide on the slope. Serious injury or property damage could result. For your safety, measure any slope before using the mower on the sloped area. Use a slope measuring device before setting up the mowing zones or operating this mower on a sloped or hilly area.
J. Winter Storage The Mower Fully charge the mower in its base station. Turn the mower off. Clean the mower and store it in dry indoor conditions at an ambient temperatures above 0°C. Base Station There are no special winter storage instructions for the base station. It can be left on the lawn during the winter. It is recommended that the power supply be disconnected from the mains during the winter.
2 Symbol Definitions Symbol Description WARNING — READ THE OPERATOR’S MANUAL(S) Read, understand and follow all the safety rules and instructions in the manual(s) and on the mower before attempting to operate this mower. Failure to comply with this information may result in personal injury or death. Keep this manual in a safe location for future and regular reference. DANGER — AVOID AMPUTATION INJURY Do not put hands or feet near or under the cutting deck.
3 Safety Features WARNING Your mower is equipped with numerous in-built safety features. However, the mower remains a hazardous device with sharp blades, which can cause serious injury to anyone who comes into contact with it. Being on the lawn while the mower is operational is strictly prohibited. STOP control/carrying handle Disabling device Interface door A. Child Lock The child lock prevents unintended operation of the mower by an accidental press of one of the buttons.
B. Anti-Theft Device (code-protected disabling device) The anti-theft device system function will prevent anyone from using or driving the mower unless they have a valid code to enter. You will be prompted to enter a four digit code of your choice to use as your personal security code. It is highly recommended that you activate this feature to prevent operation of the mower by children or people who are unfamiliar with the mower or not permitted to use it. C.
Annex A – Battery removal instructions 1. 2. 3. 4. 5. 6. Remove the disabling device. Turn the mower off by pressing and holding the GO button for 2 seconds. Insert the key into the slot and rotate left by 90°, then pull the door halfway up until it stops Rotate the key backwards by 45° and pull the door up entirely. Disconnect the battery from the mains. Press the battery housing snap to remove the battery.
Let’s get started. Can’t wait to mow your lawn.
Welcome to a friendly home Congratulations on your purchase! You are just a few steps away from meeting your best team player. Very soon you will come to count on your new friend to do a perfect job. It will automatically depart from its Base Station on predetermined days and times, mow your lawn and return to its Base Station for charging. A pre-installed perimeter wire sets the boundaries (a “virtual wall”) for your mower. It will be laid around the edges of your lawn and objects that you want to protect.
In addition, it follows the perimeter wire when it mows the edges of your lawn to give it a perfect finish. Good-looking healthy lawns are achieved by consistent mowing, which is exactly what your Robomow provides. After following the installation instructions, you will be ready to enjoy your free time, while your new friend looks after your lawn. It is highly recommended to read the complete installation guide prior to installation.
What’s in the Box x4 The product Your new Robotic Mower Perimeter Wire* Marks the working area for the mower (*) Not included in all models Base Station This is where the mower recharges itself Power Supply The power supply for charging your mower x2 Wire Pegs* For securing the wire to the ground (*) Not included in all models Spare Plot Connector For connecting the Perimeter Wire to the Base Station Base Station Stakes For affixing the Base Station to the ground Extension Cable 15 m (50 ft) low vol
Wheels cleaners Safety Guide Getting started guide Tools RoboRuler For measuring the Perimeter Wire’s distance from the lawn’s edge Tools required for installation Ready? Let’s begin...
So where are we heading? Correct installation of your mower will ensure maximum results.
Know Your Lawn Understanding your lawn will save you unnecessary mistakes and make the installation process easier and more straight-forward. You can also skip some later sections in this manual that are not relevant to your lawn type. So, what does your lawn look like? Type A Main Zone only Your lawn area is one continuous zone and all areas of the lawn are wide enough for the mower to navigate through (at least 4 m (14 ft) wide at its narrowest point).
Type C Main Zone Separated Zone Main Zone + Separated Zone Your lawn consists of two or more zones that are not connected (separated by a fence, sidewalk, pathway or other obstacle). The mower cannot drive between these zones.
Base Station 1 Location Choose locations for the Base Station & Power Supply unit The Base Station is where your mower recharges and where the perimeter wire starts and ends. In this installation step, you are going to determine a proper location for the Base Station. Where should you place your Base Station? Consideration A It is strongly recommended to place the Base Station in the Main (largest) zone of your lawn Consideration B Up to a max.
Consideration C A minimum of 3 m (10 ft) of straight wire in front of the Base Station and a min. of 1 m (3 ft) behind the Base Station to allow smooth docking Min 1m Min 3m Consideration D In a shady spot Keep a minimum of 1 meter (3.
Consideration E Make sure the ground is even and flat, and that there is no slope How to install the Base Station? ORIENTATION Place the Base Station according to the image below 24
DISTANCE FROM EDGE Use the ruler to install the wire in the correct distance from the edge of your lawn.
PEG BASE After choosing the proper location, secure the Base Station to the ground using the provided stakes. Be careful not to damage irrigation pipes when hammering down the stakes.
Plan Ahead Before you begin, walk along the edge of your lawn and plan how to set up the Perimeter Wire. Take note of all obstacles and slopes.
Obstacles and Slopes Before you put a single peg into the ground, take note of any obstacles or slopes. OBSTACLES Soft Obstacles Soft obstacles are flower beds, ponds or small trees. They need to be protected by creating Perimeter Islands. Hard Obstacles Hard obstacles are vertical, rigid and higher than 15 cm (6 in), such as trees or large hard elements that the mower can gently bump into without damaging Ponds Ponds and other bodies of water need to be protected by creating Perimeter Islands.
SLOPES Slopes along the edge To ensure your mower doesn’t slip off the lawn, especially when the grass is wet, the Perimeter Wire must exclude a slope along the edge of your lawn with an incline of over 20% - that is, 20 cm rise per 1 m [8 in rise per 3 ft]. Less than 20% Less than 20 cm / 8 in 1 m / 3 ft More than 20% More than 20 cm / 8 in 1 m / 3 ft Slopes within the Lawn Your mower can mow areas within the lawn with a slope of up to 45%.
2 Lay the Wire Lay the perimeter wire (“virtual boundary”), which defines the working area for the mower. Now you’re ready to install the Perimeter Wire. Let’s take it step by step. TIPS • Have your mower’s package nearby. • Be sure to cut your grass with your old mower one last time before you start wiring. In addition, the ground should be moist. This will make inserting pegs easier and help ensure that the mower doesn’t cut the wire. • Hammer • Combination pliers WHAT YOU’LL NEED 30 ...
Let’s make a good start Pull out approx. 50 cm (1.6 ft) of wire and peg the beginning of the wire to the ground where you intend to install your Base Station. 50cm Start unwinding the wire counter-clockwise around the lawn, starting at the Base Station’s location. Lay it loosely along the perimeter as you walk along the lawn edge. If you get to any area/object that needs special care, make sure you carefully lay the Perimeter Wire as described in the following sections.
Maintain Proper Distance The Perimeter Wire is secured to the ground by the pegs supplied with the product. Use the RoboRuler to determine the distances you should leave between the Perimeter Wire and the lawn’s edge and obstacles. • Insert pegs every 2-3m/7-10ft and at corners. At this early stage, set a minimal number of pegs. You will insert all necessary pegs later. • Pull the wire tight while hammering the pegs to their final depth in the ground. • Take care not to damage irrigation pipes.
When the edge is flat, use the short distance of the RoboRuler. 1 When the edge is a drop, use distance 2 of the ruler 2 When the edge is a wall (more than 2 cm/ 1” above the ground level), use the 3rd distance of the RoboRuler.
Leave a minimum of 1.2 m (4 ft) if the edge of the lawn borders water. Min 1.2m (4ft) Alternatively, place a physical barrier close to the water. 15cm (0.5ft) TIPS 34 • It is not necessary to bury the Perimeter Wire. • Burying the wire along exposed areas, such as pavements, is usually recommended. • If additional Perimeter Wire is required in order to complete the setup, you can extend it using the waterproof Wire Connectors provided (see page 56 “Splicing the Perimeter Wire”).
3 Soft Obstacles Protect Soft Obstacles Objects such as flower beds, ponds, or small trees must be protected by setting Perimeter Islands. Perimeter Wire position Perimeter Wire If the distance between an island and the perimeter wire is lower than 1.2m (4 ft), make the obstacle part of lawn’s edge. Keep min. 1.2 m (4 ft) between islands; if obstacles are closer together, use one island.
4 Hard Obstacles Protect Hard Obstacles Exclude from the lawn any hard objects that are lower than 15cm.
5 Slopes Slopes Your mower can handle any slope up to 45% inside the lawn Max 45% (24° ) 45cm 1m Max 45% (24° ) 37
Exclude any slope greater then 20% that are on the edge of your lawn to prevent the mower from slipping outside your lawn (especially in wet conditions) < 20% (11°) 20% = H = 20cm L= 1m > 20% (11°) 38
6 Narrow Pass Recall Your Lawn Type Main Zone Main Zone Sub Zone Separated Zone Main Zone Main Zone Sub Zone Separ. Zone Type A Type B Type C Type D Main Zone only Main Zone + Sub Zone Main Zone + Separated Zone Main Zone + Sub Zone + Separated Zone How to Wire a Sub Zone Type B / Type D Don’t have a Sub Zone? Skip this section! A Narrow Pass connects the Main Zone with a Sub Zone.
W A Narrow Pass connects the Main Zone with a Sub Zone. For passages greater than 2m (6.5 ft), the mower will be able to drive through. W > 2m Min 1.
When a narrow pass is between 1-2m (3-6ft), the wires should be installed in the middle of the path with RoboRuler distance 1 between them to allow the mower to be able to follow the wires in and out of the sub zone. On the entrance to the path from both directions, you should break the corner to 45 degrees so the mower will turn accurately in and out the narrow pass. 1m < W < 2m 45° 45° W Narrow Passes should be firm, level, and smooth.
7 Separated Zone F. How to Wire a Separated Zone Type C / Type D Don’t have a Separated Zone? Skip this section! Extend the Perimeter Wire from the Main Zone, over the obstacle.
TIP • • • Splicing the Perimeter Wire (as needed) Insert both wire ends into the leftmost and rightmost positions on the connector. Verify that the wires are fully inserted into the connector. Use a pair of pliers to press the button on top of the connector. The button should be fully pressed, without damaging the connector.
8 G. Complete the installation Complete Wire Setup Once the Perimeter Wire has been laid completely and you are back to the Base Station, install the last peg aprox. 5cm (2 in) in front of the base. It is very important that the wire will be in-line with the center of the Base Station. TIPS Unwind the wire up to about 50 cm beyond the Base Station and cut it.
Open the back door of the Base Station.
Install the connector to the tip of the wire as described in the drawings. Cut the wire end, close to the connector.
Peg the wire to the ground. Twist and wrap the wires so they could fit nicely in Base Station compartment. Connect the wire end marked with ‘A’ to the connector marked with A on the back of the Base Station. Connect the other end to the other connector. Tuck the wire in and close the door.
LED Indicators Now you should see the LED indication on the Base Station blinking green (if the mower is outside the Base Station), or steady green (if the mower is inside the base). Steady Green Mower in base Steady Red Blinking Green LED Mower out of base Blinking Red Orange 4 sec 4 sec Caution The Extension Cable from the Power Supply to the Base Station should be securely fastened to the ground! It should never present a tripping hazard. The Extension Cable should cross ONLY over soft surfaces.
One Time Setup Turn the mower on and follow the initial settings to get it ready for work. A.
Time Set time Installation done by... Select who is performing the installation. Test wire position Ensures the robot can follow the wire without obstructions. Your mower will follow the wire and stop wherever an adjustment of the wire position is needed. Follow the instructions on the mower screen. Read more in Annex B. What type is your lawn? Choose ‘Main+’ if lawn has more than 1 zone.
Main Zone size Set your Main Zone size. Separated zone If you have a separated zone in your lawn, you need to set the separated zone switch to ‘ON’. This will allow you to select “separated zone” from the mower’s home screen to initiate mowing after manually placing the mower in your separated zone. Remember to bring your mower back to the Base Station at the end of an operation in a separated zone so that it can charge and be ready to continue the automatic plan without missing an operation.
Set Cutting Height You can set the cutting height by rotating the Knob right/left. Once done press next. If the grass is high, to get the best cutting results, it is recommended to start high and lower the mowing height gradually over a couple of weeks. Schedule Plan The Mower calculates the suggested automatic mowing plan according to your lawn size. To start the automatic plan you need to approve it, or you can choose to change it from this screen or come back to it later for adjustment.
Annex B - Test wire position 1. While your mower is driving on the wire please observe for the following possible situations: a. Wire too close to obstacles If the mower encounters an obstacle while following the wire, it will maneuver around it. In these situations, adjust the wire further away so that the mower will clear the obstacle without having to depart the wire and navigate around it. b.
2. To test any adjustments you make to the wire, simply press the stop control, and carry the mower to a location on the wire approx. 3m before the area that was adjusted. Send it Home again. Repeat this process as many times, per location and on as many locations as necessary until you are happy with how it navigates the entire perimeter. 3. Once the mower has made it all the way around the perimeter it will dock inside the base station.
Secure wire Now it’s time to add some pegs along the wire. Using the remaining pegs along the Perimeter Wire, between 0.5m to 1m (1.5ft to 3.3 ft) apart.
Additional options with the mobile app Your mower is a smart connected product. It comes with a built-in Bluetooth LE (Low Energy) device that enables you to control your mower from your smartphone. A free complementary mobile app will allow you to experience your mower in a whole different way! You can download the Robomow app from Google Play Store (Android) or from Apple AppStore (iOS). After downloading, you can register your mower and enjoy much more.
Well Done! Now relax, and let your mower do the work.
1 2 3 4 5 6 7 8 58 Knowing your mower Menu structure Automatic operation Manual operation Features - how to Periodic maintenance Troubleshooting FAQs
your 1 Knowing mower In order to fully enjoy your mower, learn about its different parts and messages. Understanding how it works and behaves will lead to its smooth and easy operation.
Blade disk Front wheel Guard wires Mow motor Drive motor Battery door Drive wheel 60
Under the Hood Parts Operation panel On/Off/Go Button Navigation Keypad Return Button Mowing Height Adjustment Knob 61
LCD display Anti-theft /Child lock Time & Date Bluetooth Battery status Select zone Settings M Edge mow before mowing 62 Mowing mode Schedule On/Off • • • next operation charging automatic depart status Previous operation
Base Station LED indication Steady Green Mower in base Steady Red Blinking Green Mower out of base LED Blinking Red Orange 4 sec 4 sec Indication Meaning Steady green Perimeter wire signal is OK; the mower is inside the base Blinking green Perimeter wire signal is OK; the mower is outside the base Steady red No charging Blinking red Poor perimeter wire connection or the wire is too long Orange Type signal has changed A/B/C 63
2 Menu structure Mower Options Configure user preferences M A/B/C A/B/C Child Lock Lock the keypad to prevent accidental operation Anti - Theft PIN Code protection Time and Date Set date & time Format Select Time format (24/12) and Unit format (meters/feet) Language Change mower’s menu language 64
Sound Turn Sounds on/off Signal Type Change to avoid interference with other robotic mowers around Storage mode Minimizes power consumption during winter or other long periods where mowing is not needed while mower is left on base station. Wire turn mode Allows more efficient mowing operation by enabling smooth, continuous turns at the lawn edge. Lawn Options For a full description of all menu items, please refer to the Features section of this document.
Near Wire Follow Prevents wheel tracks along the same path by driving along the perimeter wire with a dynamic offset (not centred On wire) Separated Zone Allows you to operate the mower in separated zones Edge mow Enable or disable edge mowing on automatic operations Intensive Mowing Temporarily increases the mowing intensity to maximum for 7 days 66
Automatic 3 operation Learn how to configure automatic operation and manually bypass/override it when needed • The Zone Size setting is used by the mower to automatically determine the required mowing time for your lawn, and to recommend a weekly schedule for best results. • This schedule includes the available working days, as well as the recommended working window available for each day. • You can modify the working days and the working window according to your needs.
• You can split the daily working window into two separate windows if you’d like the mower to stay off the lawn for a time in between. Keep 2 hours gap between the working windows • It’s important to not overly limit your mower’s working time. Keeping the schedule open will allow your mower to better adapt to changing conditions and reach the needed working hours for the week.
Mowing Hours • Though your Robomow determines a smart schedule based on the size you set for your lawn, you may find the need to adjust from this at times. • The mowing time required to maintain your lawn can very on factors such as: grass type, weather / time of year, sunlight exposure, soil drainage, fertilizing, etc... Because of this, it is recommended that you monitor the quality of your lawn and make adjustments as needed.
Note: • For best results - It is recommended to not set more than 2 days in a row without mowing. • After the necessary mowing is completed for a given day, the mower will stay in its Base Station until the next working day. • By default the mower will be set with intensive mode switched ‘On’. In this mode the mower will temporarily (for 7 days) work in the maximum capacity mowing mode.
Turning automatic operation on/off • The automatic operation comes disabled by default. • During the one-time setup, the mower will guide you to set your lawn size. When done you will be able to review the offered automatic plan, change it and enable it. • If needed, you can switch off automatic departure completely by toggling the schedule on / off in the main screen. • If you want, you can also stop automatic operation on a specific zone in the lawn settings section.
Manual 4 operation Manual Operation is used when you want to start a mowing operation, regardless of the mowing schedule. Manual Operation with or without edging To initiate Manual Operation: Choose between the two operation modes Edge+Mow or Mow. M Mow Edge + Mow Select zone M M 72 Select the zone you want the mower to mow by tapping the select zone icon. Select zone, then tap the Mow mode. Note: Edge mode is not available for Sub-zones.
Features 5 how to Adjusting the mowing height • • • Lift the interface door at the top of the mower. Set the mowing height by rotating the knob left or right. The cutting height is displayed on the LCD. The mowing height’s range is 20-100 mm (0.
Child Lock This feature is turned Off by default. To turn this feature on: Tap the settings icon, then tap the mower icon. Navigate to “Child Lock” and toggle On to enable. After a delay of 10 min without touching the screen or keypads, the mower will become locked. A/B/C A/B/C To temporarily release locked keys: Press and hold Up and Back buttons for 3 seconds. The keys will relock after 2 min. without user intervention.
Anti-Theft / Lockout The Anti-Theft prevents anyone from using or driving your mower unless they have a valid code to enter. By default, this feature is turned Off.
Islands If you have big islands (like ponds or large flower beds) in this zone you can set the ‘Island’ switch on to help the mower find its base more efficiently. Size This is where you set your lawn size. Lawn size is important, as it is being used by your mower to calculate the amount of mowing hours needed. Sub Zones Use this section to add or modify sub zones. Just follow the screen instructions to choose the zone size, define the zone entry point, and set other parameters unique to each zone.
Near wire follow Use this feature to reduce wheel tracks along the perimeter when the mower travels back home to the Base Station. It works by allowing the mower to travel at various distances from the wire on each trip instead of always being centered directly over the wire. Each lawn is different, so will require some experimentation to find the optimum min. and max. values. Separated Zone If you have a separated zone in your lawn, you need to set the separated zone switch to ‘ON’.
Intensive mode If at any time during the season, the mower has gotten far behind on coverage (possibly due to being switched off for an extended time, or because of a burst of very fast grass growth, etc...) you can re-enable Intensive Mowing to allow for the mower to catch back up. This will operate the mower at max.
Wire turn mode Allows more efficient mowing operation by enabling smooth, continuous turns at the lawn edge.
Advanced Settings Storage mode Minimizes power consumption during winter or other long periods where mowing is not needed while mower is left charging in the base station. Out of the box Will reset all settings to the factory defaults. The one time setup mode will be initiated. Reset settings This action will reset all mower and lawn settings. including the automatic schedule plan.
Periodic 6 maintenance WARNING Severe injury and damage hazard! Always remove the disabling device and power the mower off before lifting the mower. Blades are very sharp. They can cause severe cuts or lacerations. Always wear heavy work gloves when working with or around the blades. NEVER use a damaged or broken blade. After periods of ongoing prolonged precipitation it is advised to remove grass build-up from mowing deck, guard wires and wheels to ensure an ideal cutting result.
Winter storage The mower • • • Turn Schedule Off and charge the mower fully in its base for 24 hours Remove the disabling device and power the mower off Clean the mower and store it in dry indoor conditions at ambient temperatures above 0˚C. Base Station • • No winter storage is required for the Base Station. It can be left on the lawn during the winter period. It is recommended to disconnect the Power Supply from the mains during the winter storage period.
7 Troubleshooting Message Displayed Cross Outside Stuck In Place Check Mow Height Check Power No Wire Signal / Waiting for Signal Probable Cause / Event The Perimeter Wire is too close to the edge. The lawn slope near the edge is too steep and causes the mower to slip outside. The lawn’s edge is too bumpy. The mower got stuck in place. It cannot continue driving. Corrective Action Move the wire towards the inner side of the lawn. Do not include areas with very steep slopes near the perimeter wire.
Frequently asked 8 questions Mower does not dock properly and sometimes misses Base Station’s contacts The entrance to the Base Station is not flat. Fill some ground to flatten the lawn around the Base Station to allow smooth entrance. Make sure the Perimeter Wire is straight before and after the Base Station. Poor quality of mowing The blades may be dull. Turn off the mower, remove the disabling device and replace them if needed. Use heavy gloves when inspecting blades.
MTD Products Aktiengesellschaft Industriestraße 23 | 66129 Saarbrücken | Germany
