RM-770 ROBOT VACUUM CLEANER
Thank you for purchasing the Robomaid RM-770 Robot Vacuum Cleaner. Please read this manual carefully before using this product. Warning! No one other than official Robomaid service personnel may disassemble, repair, or alter this product, otherwise fire, electric shock or personal injury may be caused. Do not use any charger other than that enclosed with the Robomaid, otherwise damage may be caused to the product and may result in fire or electric shock.
Components RM-770 Robot Vacuum Cleaner Mopping Attachment (2 x cloth and holder) Virtual Wall Spare Filters Docking Station 2 x Side Brushes Cleaning Brush Remote Control Power Adaptor User Manual Furniture DVD Protection Quick Start Guide Adhesives Warranty Card Names of Parts Top View: Front Bumper Infrared Receiver LED Display / Control Panel Mode Button Select Button UV Button Activate Button Dustbin Bottom View: Sensor UV Lamp Sensors Charging Contact Points Front wheel Side Brush Lef
Names of Parts Docking Station Clock Button Adjust Button Timer Button On/Off Button Full Go Button Skidproof Floor Pads Infrared Transmitter Power Adaptor Socket Charging Terminals Remote Control Indicator Auto Button Wall-Following Button Left Pause LED Display / Control Panel On/Off Button Docking Button Spot Clean Button Auto Indicator Forward Spot Indicator Right Battery Power / Docking Backward Indicator UV button Speed Adjuster Digital display Time Indicator UV Indicator Error indicator Dirt
Standby Mode • Switching the power switch to ON (see the figure below) switches the Robomaid ON and into Standby Mode. • In Standby Mode, the current mode will be displayed (the default is “AUTO 1” ). • If the Robomaid is left in Standby Mode for more than 3-5 minutes, it will start chirping every 30 seconds until the Robomaid is activated, switched OFF, or recharging. • To turn the RM-770 off, just switch the power switch to the OFF position.
Charging Mode • You can directly charge the cleaner with the Power Adapter or with the Docking Station. (See Figure 2) • To charge directly via the power adaptor, connect the power adaptor to the charging socket on the RM-770. (See Figure 1) • When charging with the Docking Station, the Robomaid must be switched ON. • When charging with the Power Adaptor, the Robomaid can be switched ON or OFF, however it can not be activated until the power adaptor has been disconnected.
Operating the Robomaid • The Robomaid must be switched ON to be activated. • The Robomaid may be activated from Standby Mode or Charging Mode from the Docking Station.
How to use the Remote Control: The Power Button “ ” • When the Robomaid RM-770 is switched on, press the Power Button for the cleaner enter Sleep Mode, which will save power and all indicators will be off. • When the cleaner enters Sleep Mode, it can not be started by pressing any button on either the cover or the remote control. • Press this button again to enter Standby Mode.
How to use the Docking Station: Connect the Power Adaptor to the Docking Station. The display will show the time and day as being Monday 8:00 am. There are 5 buttons as shown in the figure below, including: ON/OFF Button “ ”, Full Go Button “ Clock Button “ ”, Timer Button “ ” Adjust Button “ ”. Please note the buttons will only work if the Robomaid is NOT charging on the Docking Station.
How to Use The Virtual Wall The Virtual Wall sends a special infrared signal to prevent the Robomaid RM-770 from entering unnecessary or unwanted areas or to reduce the cleaning area. 01. Before using the Virtual Wall, install the batteries as shown in Figure 3, open the bottom cover of the Virtual Wall, install 2 x D batteries. After the installation, close the bottom cover and tighten the screws. Make sure you put the batteries in the correct way. 02.
Using the Mopping Attachment • When using the mopping attachment (See figure 4), The Robomaid will mop the floors while vacuuming, resulting in a more thorough clean. • The mopping cloths can be used dry or damp. • Attach the specially designed Robomaid mopping cloth to the mopping holder. (See Figure 1) • Align the clips at end of the mopping holder (See figure 2) to the sunken positions on the inner sides of the 2 wheels (See Figure 3) and clipped them in place.
How to Replace and Clean the Filters Removal and Cleaning of Filters: • Hold the middle part of the filter tray located on the inside of the dustbin (See figure 1) and then slide out (See figure 2). • The filters will easily lift out (See figure 3) • Unclip the rear fliter grill (See figure 4). • Take out the filter inside (See figure 5). • The filters can be cleaned in water and then reused after drying. It’s recommended to clean and replace them regularly.
Main Brush How to Remove the Main Brush • Unscrew the main brush mount cover (See Figure 1) using the screw driver. • The brush and main brush mount cover will lift off (Figure 2). Remove and Clean the ends of the Main Brush as often as needed! F igure 1 F igure 2 How to Install the Main Brush • Align the brush with the brush motor by inserting the square end of the brush into the main brush motor. • Insert the pin shown in Figure 1 into the matching hole in the main brush mount cover.
Troubleshooting If you experience some issues while using your Robomaid RM-770, please use the following guide and please feel free to contact our Customer Care team. The Robomaid Stops while Working • Check if the selected cleaning time is over. • Check if there’s any error information on the LED display and refer to the following table of error codes. Error Code Indicated Problem Solution 0 Left Wheel is jammed or has no traction. Check the wheels for any obstacles jamming them.
Troubleshooting (cont.) Robomaid keeps getting stuck • Check the error code and refer to the table on the previous page. • The Robomaid is about 11cm high, but can get stuck on furniture that has a gap of between 10-11cm. If this is the case, try sectioning the area off with a Virtual Wall or if possible, increase the height of the furniture by 1cm. • If the Robomaid is getting stuck on carpet, check that the mopping attachment is removed.
Due to continual product improvement in design or otherwise, the product you purchase may differ slightly from the illustrations in this book.
