Specifications
Motor Protection Controls
Phase Loss and Reversal Protection • Ultra Low Cost
ICM Control Features and Applications Specifications Replaces
ICM401
• Low cost 3-phase protection for single side
• Monitors for phase reversal, phase loss, unbalance % as a
function of input voltage
• Bright LED indicators for ON and FAULT
• Universal 3-phase input: 190-600 VAC
• Highly reliable passive electronics
• Epoxy coated for added protection
• Patented: U.S. Patent No. 5,337,206
• For open-board model order ICM403
• Voltage: 190-600 VAC
• Frequency: 50-60 Hz
• Control: 18-30 VAC
• Output:
• Relay: SPST
• N.O.: 10 amps
• Dimensions: 3.25” x 3” x 1.25”
• Supco: TPMP2
• Mars: 32536
ICM402
• Low cost 3-phase protection for single side
• Monitors for phase reversal, phase loss, unbalance % as a
function of input voltage
• Bright LED indicators for ON and FAULT
• Universal 3-phase input: 190-600 VAC
• Highly reliable passive electronics
• Epoxy coated for added protection
• Patented: U.S. Patent No. 5,337,206
• For open board model order ICM404
• Voltage: 190-600 VAC
• Frequency: 50-60 Hz
• Control: 115 or 208/240 VAC
• Output:
• Relay: SPST
• N.O.: 30 amps
• Dimensions: 3.25” x 3” x 1.25”
• Supco: TPMP2
• Mars: 32536
3-PHASE LINE VOLTAGE MONITORS - Full Performance
ICM’s line voltage monitors were specifically designed to protect compressor motors and other 3-phase loads from
premature failure or damage due to common voltage faults. They offer complete system protection by monitoring both the
line (front) and load (back) side of the system including the power, motor and contactor lines. In addition, an integral “delay
on break timer” guards against rapid short cycling at both the control circuit and the 3-phase lines. Compact and easy to
install, the ICM400 and ICM450 provide highly reliable protection for your valuable equipment.
ICM Control Features and Applications Specifications Replaces
ICM400
• Lower cost, full performance version featuring bright LED
indicators to display system faults
• Monitors ”front” and “back” sides of system
• Universal voltage operation: 190-630 VAC
• Knob-adjustable features and system set points
• Reset mode: choice of auto or manual (lockout)
• Built-in anti-short cycle protection
• Protects against voltage unbalance, high/low
voltage, phase loss, reversal, faulty power,
incorrect sequencing and rapid short cycling
• Voltage: 190-630 VAC
• Frequency: 50-60 Hz
• Voltage unbalance: Adjustable: 2-25%
• Control: 18-240 VAC
• Delay on break timer: .1-5 minutes
• Output:
• Relay: SPDT
• N.O.: 10 amps
• N.C.: 6 amps
• Dimensions: 6.5” x 4.25” x 1.5”
• A-1:
EAC-800
EAC-8000
EAC-8002
• Diversified:
AC-2020
AC-301
AC 302
• Mars: 32512, 32515,
32516, 32517
• Motorsaver: 455
• SSAC: QLM/QLV
• Time Mark: 265
• Wagner/DiversiTech:
DTP-3, WPC-800
ICM450 (ICM450S for Spanish)
• Fully programmable with LCD diagnostic display
• Easy to configure - simple push button setup
• Easy to customize - set points, variables and features are fully
adjustable and may be defined by the user while in control
SETUP mode
• 25-fault memory storage, non-volatile
• Independent high and low voltage settings ideal for dual
voltage compressor applications
• Identifies front and back side faults
• Reset mode: choice of auto or manual
• Protects against: voltage unbalance, high/low voltage, phase
loss, reversal, faulty power, incorrect sequencing and rapid
short cycling
• Reliable, high temperature LCD to 167˚F
• Simultaneous voltage display, no scrolling
• Line voltage programmable
• Universal voltage operation: 190-630 VAC
• Voltage: 190-630 VAC
• Frequency: 50-60 Hz
• Voltage unbalance: Adjustable: 2-25%
• Control: 18-240 VAC
• Delay on break timer: 0-10 minutes
• Output:
• Relay: SPDT
• N.O.: 10 amps
• N.C.: 6 amps
• Dimensions: 6.5” x 4.25” x 1.5”
• A-1:
EAC-800
EAC-8000
EAC-8002
• Copeland: 085-0160-00
• Diversified:
AC-2020
AC-301
AC-302
• Mars: PFM-2000
• Motorsaver: 455
• SSAC: QLM, QLV
• TimeMark: 265
• Wagner/DiversiTech:
DTP-3, WPC-800
ICM’s line voltage monitors continuously monitor incoming line voltage to provide superior motor protection
from premature failure and damage due to voltage unbalance, high and low voltages, phase loss, phase
reversal, faulty power, incorrect sequencing and/or rapid short cycling. Some models include LED indicators or
LCD diagnostic displays to indicate the current system condition. Single phase surge protectors help protect
your system against lightning, power surges and voltage surges.
315.233.5266
Phone
All features and specifications subject to change without notice.
Customer Service Fax
315.233.5282
Application Assistance
800.365.5525
Visit www.icmcontrols.com to find all
of our latest products, sell sheets and wiring diagrams
15