Sound for Generations ROBERTS CR9961 3 Band Single Alarm Clock Radio Please read this manual before use
Contents Contents ............................................................................ 2 Controls .......................................................................... 3-4 Switching on and setting the time .................................... 5 Listening to the radio ........................................................ 6 Setting alarm time ............................................................. 7 Checking alarm time .........................................................
Controls (Top) 2 4 5 6 1 1. Hour button 4. Time button 2. Minute button 5. Alarm off button 3. Sleep button 6.
Controls (Left) (Right) 7 8 11 7. Function switch 10. Volume control 8. Tuning control 11. Back-up battery compartment 9.
Switching on and setting the time Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the mains lead into a wall socket and switch on the wall socket. 2. The clock display will flash 12:00. Ensure that the Function switch is set to the 'Off' position. 3. Press and hold down the Time button. 4. Whilst holding down the Time button press the Hour or Minute buttons to set the correct time. Release the buttons when the correct time is reached.
Listening to the Radio 1. Switch on your clock radio by sliding the Function switch to the 'On' position. The LED dial pointer will light up indicating that the radio is switched on 1 2. Slide the Waveband switch to the required waveband. 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated in the dial scale. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception.
Setting alarm time The alarm can be set to wake you by either the buzzer or the radio. 1. Press and hold down the ALARM/OFF button. 1 2 2. Whilst holding down the ALARM/OFF button press the Hour or Minute button to set the correct time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. 2 Checking alarm time 1. To check the Alarm time, press the ALARM/OFF button.
Setting the alarm to wake to buzzer 1. Set the alarm time as previously described. Set the function switch to the 'Buzz' position. The Alarm indicator will light. The buzzer alarm will sound every day at the preset time for 1 hour and 59 minutes. To turn off the alarm until the next day press the ALARM/OFF button. To turn off the alarm permanently set the Function switch to the 'Off' position. 1 Setting the alarm to wake to radio 1. Set the alarm time as previously described.
Snooze control 1. The buzzer or radio alarm can be silenced for 9 minutes by pressing the Snooze button. This sequence can be repeated several times during the alarm period. 1 Sleep timer 1. The radio can be set to switch off automatically after a preset time has elapsed. 2 2. Press and release the Sleep button, 59 minutes is displayed. The radio will be on for 59 minutes then turn off automatically. 3.
Headphones 1. A Headphone Socket (3.5mm) located on the back of the unit is provided for use with either headphones or an earpiece. Inserting a plug automatically mutes the internal loudspeaker.
Specifications Circuit Features Power Requirements AC 230 volts, 50Hz Back-up Battery IEC size 6F22/06PP (6LR61, PP3) Frequency Coverage FM 87.5 - 108MHz MW 525 - 1605kHz LW 150 - 285kHz Loudspeaker 8 ohms Output power 0.8 Watts Aerial System FM Wire Aerial MW/LW Built-in Ferrite Bar aerial only Mains The Company reserves the right to amend the specification without notice.
General Fuse Do not allow this unit to be exposed to moisture (e.g. dripping or splashing) or to temperatures exceeding 70 degrees centigrade. It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW/LW bands. This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug (BS1363). If another type of plug is used a 5A fuse should be fitted in the plug, adaptor or distribution board.
Notes 13
Notes 14
Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Receivers with removed or defaced serial numbers.
ROBERTS RADIO TECHNICAL SERVICES 97-99 Worton Road Isleworth Middlesex TW7 6EG Issue 1 Technical Helpline:- 020 8758 0338 (Mon-Fri)
