ROBERTS CR9902 Sound for Generations 3 Band Dual Alarm Clock Radio CR9902 Instruction Book.
Controls (Top) 7 O ff B u z z A u to O n 8 CR 9902 3 V o lu m e 6 Dual Alarm 9 FM 1 5 M W LW 3 B a n d C lo c k R a d io F ast 2 2 S lo w T im e S et A la r m 1+2 Low D im m e r H ig h 10 1 / O ff A la r m S le e p (Left side) 14 13 12 (Right side) 11 1. Dimmer switch 6. Time set button 11. Alarm set button 2. Alarm selector switch 7. Headphone socket 12. Alarm off button 3. Function switch 8. Volume control 13. Snooze button 4. Fast forward button 9.
Controls (Front) 15 16 17 150 LW 17 0 210 240 260 kH z PM M W 540 600 800 FM 88 92 96 10 0 0 13 0 0 16 0 0 kH z 10 8 M H z 2 1 19 10 0 10 4 10 6 18 15. PM indicator 18. Battery compartment (underside) 16. Alarm 2 indicator 19. Alarm 1 indicator 17. LED dial pointer If you need any further advice, please call our Technical Helpline on :2 0181 758 0338 (Mon-Fri) CR9902 Instruction Book.
Switching on and setting the time Before using your clock radio you must first set the correct time. ON 1. Place the unit on a flat surface. Plug the mains lead into a wall socket and switch on. 15 0 LW 17 0 21 0 24 0 26 0 kH z P M M W 54 0 60 0 80 0 FM 88 92 96 10 0 0 130 0 160 0 kH z 10 8 M Hz 2 1 10 0 10 4 10 6 2. The clock display will flash 12:00. P M 2 1 3. Press and hold down the Time Set button. 4.
Listening to the Radio 1. Turn on the radio by sliding the Function switch to the 'On' position. The LED dial pointer will light up indicating that the radio is switched on. O ff B u z z A u to O n 150 LW 170 210 M W 540 600 800 FM 88 92 96 240 10 0 0 10 0 260 13 0 0 10 4 kH z 16 0 0 kH z 10 6 10 8 M Hz 240 260 2. Select the required waveband using the Waveband selector switch. FM M W 3. Tune in to the desired station by rotating the Tuning control.
Setting alarm times The alarms can be set to wake you by either the buzzer or the radio. Your alarm clock radio has 2 separate alarms which can be set to activate at different times. Setting alarm 1 2 1 1. Slide the Alarm function switch to the ' 1+ 2 1 ' position. 2. Press and hold down the Alarm set button. T im e 3. Whilst holding down the Alarm Set button press the fast forward (Fast), or slow reverse (Slow) buttons to set the required alarm time.
3. Whilst holding down the Alarm Set button press the fast forward (Fast) or slow reverse (Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Checking the Alarm Times 1. To check alarm 1 time, set the Alarm function switch to the ' position. 2 1 1+ 2 1' 2. Press the Alarm Set button to display the alarm 1 time. 3.
Setting the alarms to wake to buzzer O ff B u z z A u to O n 1 2 1+ 2 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. Set the Alarm selector switch to the ' 1 ', ' 2 ' or ' 1 + 2 ' position. The corresponding Alarm indicators will light. The buzzer alarm will sound every day at the preset time for 59 minutes. To turn off the alarm until the next day press the Alarm/Off button.
Snooze control The radio or buzzer alarm can be silenced for 7 minutes by pressing the Snooze button. This sequence can be repeated whilst the alarm is sounding. S le e p / O ff A la r m Sleep timer The radio can be set to turn off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed.
General Fuse Do not allow this unit to be exposed to water or steam. It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW or LW bands. This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug (BS1363). If another type of plug is used a 5A fuse should be fitted in the plug, adaptor or distribution board.
Specifications Circuit Features Power Requirements Loudspeaker Mains AC 230 volts, 50Hz Back-up Battery IEC size 6LR61 (6F22, PP3) Output power 350mW Aerial System Frequency Coverage FM 87.5 - 108MHz MW 525 - 1610kHz LW 150 - 260kHz 8 ohms only FM Wire Aerial MW Built-in Ferrite aerial LW Built-in Ferrite aerial ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice.
Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Receivers with removed or defaced serial numbers.
