Installation Guide

2. TECHNICAL DATA
Product Type: Advanced Acrylic Latex
Color: Beige
Odor: Very mild, non-offensive
Open Time: Up to 20 minutes
Working Time: Up to 30 minutes
Curing Time: 8 to 10 hours. Environmental factors and substrate
porosity effect cure rate. Restrict foot trafc and moving
of heavy objects for 24 hours to allow adhesive to cure
properly. Premature trafc can cause installation failure.
Trafc: Residential: 24 hours
Commercial: 24 hours
Rolling Loads: N/A
pH: Must not exceed 9
Shelf Life: 2 years from date of manufacture when stored in the
original unopened container in a controlled environment
50ºF - 77ºF (10ºC - 25ºC)
Storage: Protect from freezing
VOC: < 2 g/L
3. INSTRUCTIONS
Limitations
• This product is not recommended for solid wood ooring, bamboo ooring or
exotic wood ooring species
• Use for engineered plank greater than 5” wide only if ooring manufacturer
does not require moisture-cured urethane or silane-type adhesives
• On grade and above grade installation only
• Engineered wood planks greater than 5" wide must be installed above grade
on wood substrate
• Moisture tolerance over concrete slab – up to 3lbs MVER / 75% RH
• Concrete slab pH must not exceed 9
Preparation
Suboors must be structurally sound, dry, smooth, at (≤3/16" within 10'),
level and free of excess moisture/alkali and all contaminants (oil, debris, paint,
sealers, adhesive residue, etc.) that may inhibit the bond of the adhesive or the
performance of the ooring and its installation. All substrate cracks, chips,
holes, joints, high spots and irregularities must be adequately repaired. Patching
compounds must be suitable for the use application, cement-based and polymer-
modied, and applied according to the manufacturer’s instructions.
Installation
Maintain a consistent temperature (between 65-85°F) and maximum ambient
RH of 65% for 48 hours before, during and after installation. Follow all industry
standards and oor covering manufacturer’s recommendations for oor
atness, acclimation and application of all ooring materials. Pour adhesive
directly from the pail to the substrate as needed. Use appropriate trowel size
to apply the adhesive. Adhesive ridges should be well dened, consistent
and achieve full coverage of the substrate. Observe the Open Time. Do not
allow the adhesive to skin over. Apply ooring per manufacturer’s specic
guidelines. Press the board rmly into the adhesive. Lift a board periodically to
ensure 100% transfer of adhesive has occurred to promote a void-free bond.
Roll ooring installation per manufacturer’s recommendation
Clean-up
Fresh adhesive – warm, soapy water on a clean cloth.
Dried adhesive – mineral spirits sparingly on a clean, cotton cloth.
DO NOT POUR DIRECTLY ONTO FLOORING.
4. AVAILABILITY
USA
4 G Plastic Pail 1487-4 075378148746
1 G Plastic Pail 1487-1 075378148715
Canada
15.14 L Plastic Pail 1487RB015 075378148722
3.78 L Plastic Pail 1487RB004 075378148739
5. WARRANTY
Roberts Consolidated Inc. offers a limited-product warranty on this product
when installed in accordance with the printed specications. Lifetime
Warranty applies only for installations performed by industry certied
professional installers.
Visit robertsconsolidated.com, robertsconsolidated.com/ca or call
[phone] for full warranty details.
6. TECHNICAL SERVICES
For technical assistance or installation questions not covered in this
document, please contact our Technical Services Department at
[phone] U.S.A. / [phone] Canada.
H1924-12266
14871487
Roberts Company Canada, Ltd.
34 Hansen Road, Brampton, ON L6W 3H4
Customer Service: [phone]
Technical Support: [phone]
robertsconsolidated.com/ca
Roberts Consolidated Industries, Inc.
300 Cross Plains Blvd, Dalton, GA 30721
Customer Service: [phone]
Technical Support: [phone]
robertsconsolidated.com
MADE IN CANADA
ROBERTS
®
and the e
®
logo are registered trademarks of Roberts Consolidated Industries, Inc. • Q.E.P.
®
is a registered trademark of Q.E.P. Co., Inc.
LEED
®
and its related logo, is a trademark owned by the U.S. Green Building Council
®
• Microban
®
is a registered trademark of Microban Products Company.