Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
VG4 AutoDome Modular Camera System VG4 Audio Connections | en 81
Bosch Security Systems, Inc. User’s Manual F.01U.089.433 | 4.0 | 2008.09
9 VG4 Audio Connections
The audio version of the VG4 AutoDome has one audio input for line signals. The audio signals
are transmitted one-way and in-sync with the video signals. As a result, a door intercom
system can be connected at the camera location.
9.1 Audio Line Input Specifications
The following Line In specifications should be complied with in all cases:
– 5.5 Vpp max. Input voltage Impedance 9 Kohm, typical
– Sampling rate 8 KHz, 16 Bit, mono
9.1.1 Wire Specifications
Long distances are more susceptible to introducing noise into the signal.
9.1.2 Connections
The Audio Input must be connected to the Biphase Input as follows:
1. Remove the 110 ohm Biphase termination resistor.
2. Connect an audio source with line level to the Biphase input of the VG4 as shown in the
chart below:
9.1.3 Activating Audio Reception
To configure audio via the Web browser, do the following:
1. Open the IP AutoDome LivePage, then click the Settings tab.
2. Click the Camera Settings link from the left pane, then click Miscellaneous. The IP
AutoDome displays the Audio settings.
3. Click the Audio radio button to activate audio over IP.
i
NOTICE! The line ports of the intercom should be used for transmitting audio signals on the
intercom systems.
i
NOTICE! There is an internal gain level adjustment in case the signal level is too low.
Wire Type: Coax wire, AWG is dependant on the connector style selected
Maximum Distance: Depends on the signal level
Contact Description
Biphase + Audio In
Biphase - Ground
i
NOTICE! The audio signal is sent in a separate data stream parallel to the video data, and so
increases the network load. The audio data is encoded according to G.711 and requires an
additional bandwidth of approximately 80 Kbit/s for each connection.