Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
62 en | Configuring and Using the IP AutoDome VG4 AutoDome Modular Camera System
F.01U.089.433 | 4.0 | 2008.09 User’s Manual Bosch Security Systems, Inc.
To View a Preset Shot:
1. Click the number of the scene you want to view using the on-screen keypad.
2. Click the Show Shot button.
8.8 Alarm Connections
The Alarm Connections screen allows users to specify up to ten IP addresses which the device
attempts to establish a connection with in the event of an alarm. The device contacts the first
specified IP address and then each subsequent address until the device establishes a
connection.
Figure 8.16 Alarm Connections
To connect an alarm, do the following:
1. Open the IP AutoDome Livepage, then click the Settings tab.
2. Click the Alarm Settings link, then click Alarm Connections. The IP AutoDome displays
the Alarm Connections screen (see Figure 8.16).
3. Click the Connect on Alarm drop-down list and select On to establish a connection to a
pre-defined IP address in the event of an alarm. Off, indicates no alarm connections are
made and Follows Input x, triggers an alarm.
4. Click the Number of destination IP address drop-down list and select a number from one
to ten to specify the number of the IP addresses. To configure multiple IP addresses,
select a number for the destination IP address, configure the settings described below
and then click the Set button. You must click the Set button prior to configuring the
settings for another IP address.
5. Click inside the Destination IP address input box and type an IP address.
6. Click inside the Destination password input box and type the appropriate password for
the IP address, if required.
7. Click the Video transmission pull-down list and make a selection.
8. Click the Remote port pull-down list and make a selection. Depending on the network
configuration, select a browser port here. The ports for HTTPS connections will be
available only if the On option is selected for the SSL encryption parameter.
9. Click the Monitor pull-down list and make a selection from one to four.
10. Click the Coder pull-down list and make a selection from one to four.
i
NOTICE! For more information about the IP AutoDome settings and controls, click the Help on
this page? link to open the IP AutoDome online help.