Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
60 en | Configuring and Using the IP AutoDome VG4 AutoDome Modular Camera System
F.01U.089.433 | 4.0 | 2008.09 User’s Manual Bosch Security Systems, Inc.
To manually pan throughout the image area, move your cursor over any part of the live video.
The image area displays a directional arrow (), then click and hold the right mouse
key to pan the camera.
Digital I/O (300 and 500i Series Only)
The alarm relay outputs will display next to the camera image on the LivePage window when
the IP AutoDome is configured to Show Relay Outputs under Service Settings on the Settings
window. The relays on the camera allows you to operate a device (for example a light or a
door opener). To operate, click the relay symbol next to the video image, only if alarms are not
active. The symbol is yellow when the relay is activated.
Figure 8.13 Digital I/O Panel
System and Event Logs
The System Log field contains information about the operating status of the IP AutoDome and
the connection. The Event Log contains information about alarm conditions (see Figure 8.14
below).
Figure 8.14 System and Event Logs
8.7.4 Entering a Keyboard Control Command
The Aux Control tab is used to enter keyboard control commands. These commands are
composed of a command number plus the appropriate function key (Show Shot, Set Shot Aux
On or Aux Off). A valid combination either issues a command to the camera or displays an on-
screen menu.