Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
48 en | Advanced Features VG4 AutoDome Modular Camera System
F.01U.089.433 | 4.0 | 2008.09 User’s Manual Bosch Security Systems, Inc.
7.5 Motion Detection with Region of Interest (500i Series Only)
(Preset positions 90 through 99)
With the 500i Series AutoDome, the motion detection software can be configured to create a
Region of Interest within multiple preset positions or scenes. It can take advantage of Virtual
Masking to ignore motion in predefined areas. Motion Detection can also be used as an Alarm
Rule input.
Preset positions 90 through 99 are reserved for programming motion detection scenes.
To set up a scene with Motion Detection:
1. Choose an unused Preset position from 90 to 99. For this example use Preset scene 95.
2. Enter the keyboard command SET-95-ENTER.
3. Select YES at the Apply Motion Detection? prompt. (If NO is selected, the Preset scene
does not activate Motion Detection.)
4. Select YES at the Apply Region of Interest? prompt. (If NO is selected, the entire scene is
used for Motion Detection.)
5. Follow the on-screen menu instructions to construct the shape of the screen area you
want to detect motion within.
7.6 Image Stabilization (500i Series Only)
Image Stabilization becomes increasingly important as zoom ranges are extended. The
advanced image stabilization algorithms of the 500i Series eliminate camera shake for
exceptional image clarity. Bosch achieves this clarity without reducing camera sensitivity or
picture quality.
– To configure image stabilization, open the Main menu, select the Advanced menu, and
then select Stabilization to turn on the feature.
–In Pelco Mode open the Main menu, select the Advanced menu, and then select
Stabilization to turn on the feature.
7.7 Pre-position Tour
The 200 Series AutoDome features one (1) standard preset tour, while the 300 and 500i
Series AutoDomes feature two (2) preset tours. Each preset scene is saved for playback later.
Tour 1 is a standard tour that only recalls the scenes in the exact sequence they were shot.
Scenes can be added or deleted on the tour, but the sequence cannot be changed. To add or
remove scenes on Tour 1 enter the keyboard command SHOT-900-ENTER and follow the on-
screen instructions.
Tour 2 (300 and 500i Series only) is a customizable tour that allows you to rearrange the
sequence of scenes on the tour by inserting and deleting scenes. To enter the Edit Tour 2
menu, enter the keyboard command SET-900-ENTER and follow the on-screen instructions.
i
NOTICE! Motion Detection always takes precedence over AutoTrack object tracking.
i
NOTICE! Up to five (5) anchor points can be used to form the area which you want to detect
motion within. Motion Detection is not activated until the Preset scene is recalled. The Motion
Detection icon "M" appears in the upper left-hand corner of the display.