Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
VG4 AutoDome Modular Camera System On-Screen Display Menu Navigation | en 23
Bosch Security Systems, Inc. User’s Manual F.01U.089.433 | 4.0 | 2008.09
Advanced Feature Setup Menu Choices:
2.11 Diagnostics Menu
The Diagnostics menu provides access to a list of diagnostic tools and events.
Menu Description Sub-menu / Description Default
Setting
Exit Saves and exits the menu.
Stabilization Turns on video stabilization. OFF
AutoTrack
Sensitivity
Sets the sensitivity level of
AutoTrack.
Sliding scale: -(Auto, 1 to 20)+
Where 1 is more sensitive and 20
is less sensitive. Auto varies the
sensitivity level based on various
lighting conditions.
Auto
AutoTrack
Timeout
Toggles the AutoTrack
Timeout feature.
When On, AutoTrack “gives up”
after the Timeout Period if
tracking in a confined area (for
example a tree, a flag, etc).
OFF
AutoTrack
Timeout Period
Enters the AutoTrack
Timeout Period set menu
Sliding scale 30 sec, 1 to 30 min. 5 min
Camera Height Defines the height of the
camera for AutoTrack.
A range from 2.4 m (8 ft) to
30.7 m (100 ft)
3.6 m
(12 ft)
Virtual Masking Enters the Virtual Mask
menu. See Section 7.3 Virtual
Masking (500i Series Only),
Page 47.
Allows up to 24 virtual masks
using five anchor points.
Restore
Defaults
Restores the default settings
for this menu.
Diagnostics
Exit...
Alarm Status...
BIST...
Internal Temp: Deg F / Deg C
High Temp Events: Deg F / Deg C
Highest Temp Deg F / Deg C
Low Temp Events: Deg F / Deg C
Lowest Temp: Deg F / Deg C
Security Access: 0
CTFID Access: 0
Homing Events: 0
Homing Failed: 0
Restart Events: 0
Low Volt Events: 0
Power Up Events: 0
Video Loss Events: 0
Focus / Iris: Save and Exit