Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
18 en | On-Screen Display Menu Navigation VG4 AutoDome Modular Camera System
F.01U.089.433 | 4.0 | 2008.09 User’s Manual Bosch Security Systems, Inc.
Outputs Setup Menu
Inputs 1-7 Defines the type of physical
input.
N.O.: Normally open dry contact.
N.C.: Normally closed dry contact.
N.C.S.: Normally closed supervised
contact.
N.O.S.: Normally open supervised
contact.
N.O.
Inputs 8-12 Defines input commands that
can be used in a rule.
Command inputs can also be
customized by using non-
assigned keyboard command
numbers.
NONE: No command defined.
Aux On: Responds to a standard or
custom keyboard ON (1-99)
command.
Aux Off: Responds to a standard or
custom keyboard OFF (1-99)
command.
Shot: Responds to a Preset shot or
scene from 1-99. (200 Series 1-64).
AutoTrack: Triggers an alarm when
set to ON. (Available with 500i Series
only).
Motion Detection: Triggers an alarm
when set to ON. (Available with 500i
Series only).
NONE
Menu Description Sub-menu / Description Default
Setting
i
NOTICE! Alarm inputs 1 and 2 provide tamper detection, if programmed as supervised, for
breaks or shorts in an alarm circuit. See the AutoDome Modular Camera System Installation
Manual for wiring instructions.
Outputs Setup...
Exit...
1. Alarm Output 1 N.O. 1-4
Physical
2. Alarm Output 2 N.O.
3. Alarm Output 3 N.O. Outputs
4. Alarm Relay N.O.
5. NONE
5-12
Command
Outputs
6. Aux On 1
7. Aux Off 8
8. Shot 99
9. OSD
10. Transmit
11. NONE
12. NONE
Focus / Iris: Select Type
Right / Left: Select Mode