Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide
VG4 AutoDome Modular Camera System On-Screen Display Menu Navigation | en 15
Bosch Security Systems, Inc. User’s Manual F.01U.089.433 | 4.0 | 2008.09
2.6 Communication Setup Menu
The Communication Setup Menu provides access to baud rate and Bilinx control settings.
Menu items marked with an asterisk (*) are the default settings.
Privacy
Masking
(not
available
with 200
Series
models)
Allows masking of
sensitive areas. Up to 24
privacy masks are
available, with a
maximum limit of eight
(8) to a scene.
Exit: Saves and exits menu.
Mask: 1 to 24 masking areas. Follow the
on-screen instructions to set a mask.
See Section 7.4 Privacy Masking (300 and
500i Series Only), Page 47.
Restore Defaults: Restores the default
settings for this menu only.
Restore
Defaults
Restores the default
setting for this menu only.
Menu Description Sub-menu / Description Default
Setting
Communication Setup
Exit...
* AutoBaud: ON
* Baud Rate 9600
*Bilinx: ON
Restore Defaults...
* = Factory Setting
Focus / Iris: Select