Home Security System User Manual
Table Of Contents
- 1 Getting Started 3
- 2 On-Screen Display Menu Navigation 7
- 3 Common AutoDome User Commands (unlocked) 27
- 4 Alternative Control Protocols 29
- 5 Pelco On-Screen Menus 33
- 6 Keyboard Commands by Number 37
- 7 Advanced Features 41
- 7.1 Alarm Rules (300 and 500i Series Only) 41
- 7.2 AutoTrack Operation (500i Series Only) 45
- 7.2.1 AutoTrack Settings and Recommendations 45
- 7.2.2 AutoTrack Optimization 46
- 7.3 Virtual Masking (500i Series Only) 47
- 7.4 Privacy Masking (300 and 500i Series Only) 47
- 7.5 Motion Detection with Region of Interest (500i Series Only) (Preset positions 90 through 99) 48
- 7.6 Image Stabilization (500i Series Only) 48
- 7.7 Pre-position Tour 48
- 8 Configuring and Using the IP AutoDome 49
- 8.1 Overview of Features 49
- 8.2 System Requirements 50
- 8.3 Connecting the IP AutoDome to the PC 50
- 8.4 Configuring the IP AutoDome Camera 51
- 8.5 Installing the Required Software 52
- 8.5.1 Changing the Network Settings 55
- 8.6 Main Screen 57
- 8.7 Viewing Live Images and Controlling the AutoDome PTZ 58
- 8.7.1 Establishing a Connection 58
- 8.7.2 Configuring Data Streams 58
- 8.7.3 Controlling Camera Operations 59
- 8.7.4 Entering a Keyboard Control Command 60
- 8.8 Alarm Connections 62
- 8.8.1 Sending an Alarm E-mail 63
- 8.9 Partitioning 64
- 8.9.1 Viewing the Partition Status 68
- 8.9.2 Editing a Partition 70
- 8.9.3 Deleting Recordings 71
- 8.9.4 Deleting all Partitions 71
- 8.10 Recording Scheduler 71
- 8.10.1 Holidays 72
- 8.10.2 Deleting Holidays 72
- 8.10.3 Time Periods 72
- 8.10.4 Activating the Recording 73
- 8.10.5 Recording Status 73
- 8.11 Recording Profiles 73
- 8.12 Alarm Rules 74
- 8.12.1 Creating Alarm Rules 75
- 8.12.2 Alarm Rule Examples 76
- 9 VG4 Audio Connections 81
- 10 Troubleshooting Guide 85
- 1 Getting Started
- 2 On-Screen Display Menu Navigation
- 3 Common AutoDome User Commands (unlocked)
- 4 Alternative Control Protocols
- 5 Pelco On-Screen Menus
- 6 Keyboard Commands by Number
- 7 Advanced Features
- 8 Configuring and Using the IP AutoDome
- 9 VG4 Audio Connections
- 10 Troubleshooting Guide

VG4 AutoDome Modular Camera System Glossary of CCTV Terms | en 101
Bosch Security Systems, Inc. User’s Manual F.01U.089.433 | 4.0 | 2008.09
S
Sector Blanking The ability to blank out video in any of the 16 pan sectors.
Sensitivity A measure of the amount of light required to provide a standard video signal. Sensitivity
values are stated in lux or foot-candles.
SensUp Increases camera sensitivity by increasing the integration time on the CCD. This is
accomplished by integrating the signal from a number of consecutive video frames to reduce
signal noise.
Singlemode Fiber An optical fiber with a silica (e.g. glass) core with a diameter of less than 10 microns. Used for
high-speed transmission over long distances, it provides greater bandwidth than multimode,
but its smaller core makes it more difficult to couple the light source. Singlemode fiber optic
transmission systems use more expensive laser-based light sources.
Spot Focus Activates Auto Focus for three seconds after camera movement.
Subnet Mask Subnetting is a method that allows one large network to be broken down into several smaller
ones. Depending on the network class (A, B, or C), some number of IP address bits are
reserved for the network address (subnet) and some for the host address. For example, Class
A addresses use 8 bits for the subnet address and 24 bits for the host portion of the address.
Class A subnet masks are denoted 255.0.0.0. Class B addresses (16 bits for both the subnet
and host address) use a 255.255.0.0 subnet mask. Class C addresses (8 bits for the subnet
and 24 bits for the host address) use a subnet mask of 255.255.255.0.
T
TCP/IP See Transmission Control Protocol/Internet Protocol.
Tilt Camera movement in the vertical direction.
Transmission Control Protocol/Internet Protocol
A communications protocol suite that provides two data transport methods. TCP is a
connection-based protocol that ensures that data arrives intact and complete. UDP is a
connectionless, best effort protocol that simply sends out packets. UDP is typically used for
streaming media, while TCP is used when error-free delivery is required.
Tri-streaming A Bosch encoding technology that generates two separate MPEG-4 video streams and one
MJPEG stream simultaneously. This advanced streaming capability enables the user to tune
live viewing and recording requirements independently to meet specific site and enterprise
requirements.
U
Unshielded Twisted Pair
A variant of twisted pair cabling UTP cable is not surrounded by any shielding. The wires in a
twisted pair cable are twisted around each other to minimize interference from the other
twisted pairs in the cable. UTP is the primary wire type for telephone usage and the most
commonly used type of networking cable.
UTP See Unshielded Twisted Pair.










