PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre BT-Wifi Test Test Description internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 1 Content 2 PSA RCC Device ................................................................................................................................ 3 2.1 Front side ................................................................................................................................. 3 2.2 Back Side from A1 non DAB Variant ..................................................................................
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 2 PSA RCC Device 2.1 Front side Bluetooth Antenna Wifi Antenna 2.2 Back Side from A1 non DAB Variant LVDS USB2 USB1 USB3 LVDS FM2 AM/FM1 Main Connector 2.3 Back Side from A1 DAB Variant LVDS USB2 USB1 USB3 LVDS DAB FM2 AM/FM1 Main Connector internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 2.4 Back Side from A2 DAB-Variant GNSS AM/FM1 FM2 USB3 DAB USB1 USB2 LVDS Main Connector 2.5 Back Side from A2 nonDAB-Variant internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 3 Test Setup PC/Laptop PSA RCC DUT HSD USB cable Ethernet cable USBEthernet Adapter internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 4 Network configuration Add the IP-Adress for 172.17.0.5 for the D-Link adapter at the Microsoft network controls as shown in the next pictures. Network connection: With a double click on the LAN-connection with the D-Link DUB-E100 USB 2.0 Fast Ethernet Adapter you should be able to make the following setting under properties: In case of problems it might be necessary to restart the computer and check all items again.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 5 Putty Configuration and Use Start Putty: (Simply run Putty.EXE no installation is required.) If not configured up to now configure Putty as shown in the next 3 pictures: You can use your personal window settings under “Window”. internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre Use “root” as username for Auto-login Afterwards use “Save-Button” in “Session”-screen. From now on the session can be started by double-clicking the entry “G3G”. At the first time of starting Putty a message is displayed. The text asks if you trust the connection. Click “yes” button.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 6 Bluetooth Tests Note that the RF Power on all tests are fixed settings inside module. They cannot be changed. To start any test it is necessary to type in “./bt_rf_certification_tests.sh” added with the needed parameters which a described in the following picture: For example: Continuous Transmission at 2402MHz with DH5-Packets: ./bt_rf_certification_tests.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 6.1 Bluetooth tests with Bluetooth tester Activate Bluetooth test mode to test with a Bluetooth tester like Rohde & Schwarz CBT In order to leave this mode, the DUT has to be rebooted with the command reboot: Alternative the device can be disconnected from the power supply. Connect it some seconds later and start the device again. internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 7 WLAN Note that the RF Power on all tests are fixed settings inside module. They can not be changed. You will get a failure from Punitest if you try to change the power value. Start Punitest internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre The Punitest menue is shown: Then key in: 3 1 (CH1) 5 1 (1Mbit) 7 1 (Tx Start) A feedback is always given on the screen. The Punitest menu is shown again. internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre 7.1 Connect to WLAN-Access Point and do iPerf In order to connect to a WLAN Access Point an unsecured WLAN network with the SSID “PSA-WLAN” is necessary. If punitest was used directly before the device must be restarted before normal WLAN operation is possible. If not already done change directory with “cd /rta”. Afterwards type “./init_wifi.sh” to connect to the WLAN network.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre Do the following settings and start the test internal: Manual_iPerf_and_RTA_tests_PSA_V2.
PSA RCC manual for radio type approval tests and iPerf Car Multimedia EMC-Centre Now start iperf on the DUT. The script will ask for the IP of the iPerf-Server. Type in the IP of the PC where you started “jPerf” To stop the script use twice the key combination “STRG” + C or “CTRL” + C If a failure appears or jPerf stops working activate in addition the Compatibility Mode and repeat the steps to start the test. internal: Manual_iPerf_and_RTA_tests_PSA_V2.
