Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (B) by removing screws (D).
2. Determine desired location for light xture on wall. Hold mounting plate (A) in a
level position against the wall. Using a pencil, mark the location of the mounting
holes in mounting plate (A) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so they
accommodate wall anchors (I), provided. Insert wall anchors into drilled holes.
4. Afx mounting plate (A) to the wall by threading mounting screws (C)
through holes in mounting plate (A) and into wall anchors.
5. Slide backplate (B) over mounting plate (A). Thread screws (D) into vacant holes
at the top and sides of backplate (B) to secure xture to the mounting surface.
6. Thread cord cover (J) into nipple (E) at the bottom of the backplate. Thread
cord cover (K) onto cord cover (J).
7. Insert two (2) 60W MAX. Type A, medium base bulbs into the sockets located
inside shades (G).
8. Insert three prong plug (M) into wall outlet.
9. Use switch (L) to control power of lamp.
10. Connect ground (green or silver in color) wire from xture to ground wire in the outlet box. Fasten wires together with wire nut (H) and tightly
wrap the connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut (H) and
tightly wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (H)
and tightly wrap connection with electrical tape.
13. Slide backplate (B) over mounting plate (A). Thread screws (D) into vacant holes at the top and sides of backplate (B) to secure the xture to
the mounting surface.
14. Insert two (2) 60W MAX. Type A, medium base bulbs into the sockets located inside shades (G).
15. Reconnect main electrical supply from the fuse box/circuit breaker and test xture.
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners as they may damage the nish. *
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER. IT IS RECOMMENDED THAT A LICENSED
ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (B) by removing screws (D).
3. Cut three prong plug (M) from the end of the electrical cord.
4. From the back side of backplate (B), pull the electrical cord up through nipple
(E).
5. Cut the cord to the desired length for making electrical connection. At least six
inches of wire will be needed to make proper electrical connection.
6. Carefully unscrew nipple (E) from backplate (B). Thread plug (F) into hole
vacated by the electrical cord and nipple (E).
7. Carefully pull the wiring from wall outlet box. Thread the wires through the
center hole in mounting plate (A).
8. Afx mounting plate (A) to wall outlet box with mounting screws (C) provided.
9. Make proper electrical connections described in steps 10 - 12. A LICENSED
ELECTRICIAN IS RECOMMENDED.
B708
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety
instructions are read before beginning installation of xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn off power at switch before replacing bulbs, making sure xture has had
sufcient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
ASSEMBLY INSTRUCTIONS FOR YOUR
HAVANA DOUBLE SCONCE
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)