Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (B) by removing screws (C).
2. Determine desired location for light fi xture on wall. Hold mounting plate (A) in a
level position against the wall. Using a pencil, mark the location of the mounting
holes in mounting plate (A) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so they
accommodate wall anchors (Q), provided. Insert wall anchors (Q) into drilled holes.
4. Affi x mounting plate (A) to the wall by threading mounting screws (P) through
holes in mounting plate (A) and into wall anchors (Q).
5. Slide backplate (B) over mounting plate (A). Thread screws (C) back into holes
at the top and bottom of backplate (B) to secure fi xture to the mounting surface.
6. Thread cord cover (F) into the bottom of the backplate (B). Thread
cord cover (G) onto cord cover (F).
7. Follow steps 15 through 18 from Direct Wire Assembly Instructions, below.
8. Insert three prong plug (H) into wall outlet.
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER. IT IS RECOMMENDED THAT A LICENSED
ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (B) by removing screws (C).
3. Cut three prong plug (H) from the end of the electrical cord.
4. Remove cord covers (F) and (G) from the electrical cord. From the back side of
the fi xture, pull the electrical cord up through hole in the bottom of the back
plate (B).
5. Cut the cord to the desired length for making an electrical connection. At least
six inches of wire will be needed to make proper electrical connection.
6. Thread plug (E) into the hole vacated by the electrical cord.
7. Carefully pull the wiring from wall outlet box. Thread the wires through the
center hole in mounting plate (A).
8. Affi x mounting plate (A) to wall outlet box with mounting screws (D) provided.
9. Lift fi xture to mounting plate and make proper electrical connections described
in steps 10 - 12. A LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from fi xture to ground wire in
the outlet box. Fasten wires together with wire nut (O) and tightly wrap the
connection with electrical tape.
11. Attach hot wire from fi xture (black in color or smooth side of wire) to hot wire
from outlet box. Fasten wires together with wire nut (O) and tightly wrap
connection with electrical tape.
12. Attach neutral wire from fi xture (white in color or ribbed side of wire) to neutral
wire from outlet box. Fasten wires together with wire nut (O) and tightly wrap
connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide backplate (B)
over mounting plate (A).
14. Thread screws (C) into vacant holes at the top and sides of backplate (B) to
secure the fi xture to the mounting surface.
15. Remove fi nial (N) from harp (L). Squeeze harp (L) inward and place into the
opening of saddle (K).
16. Place shade (M) onto harp (L). Thread fi nial (N) back onto harp (L) to secure
the shade to the lamp.
17. Insert one 100W MAX. Type A medium base bulb into the socket
18. Carefully adjust arm (I) into desired position. Carefully move arm (J) into
desired position.
19. Reconnect main electrical supply at the fuse box/circuit breaker and test fi xture.
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners. *
417
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety
instructions are read before beginning installation of fi xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn off power at switch before replacing bulbs, making sure fi xture has had
suffi cient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
ASSEMBLY INSTRUCTIONS FOR YOUR
WILLIAMSBURG LEWIS SCONCE
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J )
(K)
(L)
(M)
(N)
(P)
(Q)
(O)