Installation Guide

ASSEMBLY INSTRUCTIONS FOR YOUR
MEURICE LARGE PENDANT
657
"J BOX"
(I)
(H)
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(J)
(O)
(L)
(K)
(N)
(M)
(P)
HOLD IN A
FIXED POSITION
(Q)
* SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER.
1. Remove all parts carefully from the box.
2. Unthread nipple (C) from hang straight (F). Do not remove cross bar (A)
from threaded nipple (C).
3. Afx cross bar (A) to “J BOX” using screws (B) provided.
4. Measure desired drop for xture to hang from J BOX. Using chain
break (Q) remove links in chain (G) to achieve desired drop. To open
chain links (recommend using a soft cloth to cover the link), place a cloth
around the link and sliding one of the chain break forks (Q) onto the
link. Slide the second fork onto the link with the handles facing the
opposite directions (see diagram). The backstop of the chain break fork
(Q) MUST rest against the link while applying force to prevent damage
to the link. Holding one chain break fork (Q) in a xed position, rotate
the second chain break fork (Q) to open the link. Do not rotate the link
more than 45 degrees. Rotate open link in chain (G) to a closed position
to secure xture.
5. Guide wiring from loop (H) through chain loops (G). Guide wiring
through center hole in hang straight (F), collar (E), and through center
hole in canopy (D).
6. Thread collar (E) down hang straight (F) and slide down chain links (G) to rest on loop (H).
7. Slide center hole of canopy (D) down hang straight (G) and chain links (G) to rest on loop (H).
8. Holding xture by hang straight (F), lift xture to threaded nipple (C). Guide wiring through center hole in threaded nipple (C). Pull
wiring until hang straight (F) and threaded nipple (C) are touching. Thread hang straight (F) onto threaded nipple (C).
9. Make proper electrical connection. A licensed electrician is recommended.
10. Connect the grounding wire (silver) from the xture to the grounding wire in the outlet box (copper, green, or silver). Connect the
black wire of the xture (or smooth side of the wire) to the black wire in the outlet box. Connect the white wire of the xture (or
rough side of the wire) to the white wire in the outlet box.
11. Hold canopy (D) tightly against the ceiling. Thread collar (E) up hang straight (F) to secure position of canopy (D).
12. Slide shade (L) up bottom section of xture. Slide washer (K) of shade spider into the opening between washer (I) and washer (J).
Secure position of shade (L) by threading washer (J) tightly against washer (K).
13. Install three (3) Type A, maximum 100 watt bulbs into the sockets.
14. Align center hole in diffuser (O) with threaded nipple (N). Slide diffuser up threaded nipple (N) and hold rmly against
washer (M). Thread nial (P) onto threaded nipple (N) to secure position of diffuser (O).
IMPORTANT SAFETY INSTRUCTIONS:
*These instructions are provided for your safety.
*It is very important that they are read completely before beginning the
installation of your xture.
*WE STRONGLY RECOMMEND INSTALLATION BY A LICENSED
ELECTRICIAN.
*Turn off power at switch before replacing bulbs, making sure xture has
had sufcient time to cool down.
*DO NOT subject the xture to any shock while lit as shattering of bulbs
may result.
*To clean, use soft dry cloth only. Do not use any chemical or abrasive
cleaners as they may damage the nish.
ASSEMBLY INSTRUCTIONS