Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (C) by removing screws (D).
2. Determine desired location for light xture on wall. Hold mounting plate (A) in a level position
against the wall. Using a pencil, mark the location of the mounting holes in mounting plate (A)
onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so wall anchors (N),
provided, t snugly inside the opening. Insert wall anchors into drilled holes.
4. Ax mounting plate (A) to the wall by threading mounting screws (M) through holes in
mounting plate (A) and into wall anchors (N).
5. Slide backplate (C) over mounting plate (A). Thread screws (D) into holes at the top and sides
of backplate (C) to secure xture to the mounting surface.
6. Thread cord cover (G) into threaded tube (E) at the bottom of the backplate (C). Thread cord
cover (H) onto cord cover (G).
7. Remove ange (K) from socket (L).
8. Place shade (J) onto socket (L). Thread ange back onto socket (L) to secure shade to xture.
Repeat steps 7 and 8 for the other shade.
9. Insert two (2) 40W MAX. Type B, candelabra base bulbs into the sockets (L).
10. Insert three prong plug (I) into wall outlet.
11. Use switch on cord to control power to the lamp.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (O)
and tightly wrap connection with electrical tape. Carefully push the wire connections through the center hole in the mounting plate and into the
wall outlet box.
13. Slide backplate (C) over mounting plate (A). Thread screws (D) into holes at the top and sides of backplate (C) to secure the xture to the
mounting surface.
14. Remove ange (K) from socket (L).
15. Place shade (J) onto socket (L). Thread ange back onto socket (L) to secure shade. Repeat steps 14-15 for remaining shade.
16. Insert two (2) 40W MAX. Type B, candelabra base bulbs into the sockets (L).
17. Reconnect main electrical supply from the fuse box/circuit breaker and test xture.
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER. IT IS
RECOMMENDED THAT A LICENSED ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (C) by removing screws (D). Set screws (D) aside.
3. Cut cord above switch and three prong plug (I), removing them from the end of the electrical cord.
4. From the back side of backplate (C), pull the electrical cord up through threaded tube (E).
5. Cut the cord to the desired length for making electrical connection. At least six inches of wire will be needed to make
proper electrical connection.
6. Carefully unscrew threaded tube (E) from backplate (C). Thread plug (F) into hole created by the removal of tube
(E).
7. Carefully pull the wiring from wall outlet box. Thread the wires through the center hole in mounting plate (A).
8. Ax mounting plate (A) to wall outlet box with mounting screws (B) provided.
9. Make proper electrical connections described in steps 10 - 12. A LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from xture to ground wire in the outlet box. Fasten wires together
with wire nut (O) and tightly wrap the connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires
together with wire nut (O) and tightly wrap connection with electrical tape.
593
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety instructions are read
before beginning installation of xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn o power at switch before replacing bulbs, making sure xture has had sucient time to
cool down.
* Do not connect the electricity until lamp is fully assembled.
* This xture is UL rated for dry locations.
ASSEMBLY INSTRUCTIONS FOR YOUR
VOLTAIRE DOUBLE SCONCE
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners as they may damage the nish. *
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
(N)
(O)