Installation Guide

ASSEMBLY INSTRUCTIONS FOR YOUR
582
KYOTO SWINGER WALL SCONCE
CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (C) by removing screws (B).
2. Determine desired location for light xture on wall. Hold mounting plate (A) in a
level position against the wall. Using a pencil, mark the location of the mounting
holes in mounting plate (A) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so wall
anchors (M), provided, t snugly inside the opening. Insert wall anchors into drilled
holes.
4. Ax mounting plate (A) to the wall by threading mounting screws (L) through holes
in mounting plate (A) and into wall anchors (M).
5. Slide backplate (C) over mounting plate (A). Thread screws (D) back into holes at
the top and sides of backplate (C) to secure xture to the mounting surface.
6. Thread cord cover (F) into the bottom of the backplate (C). Thread cord cover (G)
onto cord cover (F).
7. Follow steps 15 and 16 from Direct Wire Assembly Instructions, below.
8. Insert three prong plug (H) into wall outlet.
9. Control power to the xture by rotating the switch on backplate (C).
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/
CIRCUIT BREAKER. IT IS RECOMMENDED THAT A LICENSED
ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (C) by removing screws (D).
3. Cut three prong plug (H) from the end of the electrical cord.
4. Remove cord covers (F) and (G) from the electrical cord. From the back side of
backplate (C), pull the electrical cord up through hole in the bottom of backplate.
5. Cut the cord to the desired length for making an electrical connection. At least six
inches of wire will be needed to make proper electrical connection.
6. Thread plug (E) into hole at the bottom of backplate (C).
7. Carefully pull the wiring from wall outlet box. Thread wires through the center hole
in mounting plate (A).
8. Ax mounting plate (A) to wall outlet box with mounting screws (B) provided.
9. Lift xture to mounting plate and make proper electrical connections described in
steps 10-12. A LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from xture to ground wire in the
outlet box. Fasten wires together with wire nut (N) and tightly wrap the connection
with electrical tape.
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s
important that all safety instructions are read before
beginning installation of xture.
* We STRONGLY recommend installation by a licensed
electrician.
* Turn o power at switch before replacing bulbs, making
sure xture has had sucient time to cool down.
* Do not connect the electricity until lamp is fully
assembled.
* This xture is UL rated for dry locations.
(A)
(D)
(B)
(C)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
(N)
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut (N) and tightly
wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (N) and
tightly wrap connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide backplate (C) over mounting plate (A).
14. Thread screws (D) into holes at the top and sides of backplate (B) to secure the xture to the mounting surface.
15. Remove ange (J) from socket (I). Place shade (K) onto socket (I). Thread ange (J) back onto the socket to secure the shade to the xture.
16. Insert one 60W MAX. Type B, candelabra base bulb into socket (I).
17. Reconnect main electrical supply at the fuse box/circuit breaker and test xture.
18. Control power to the xture by rotating the switch on backplate (C).
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners. *