Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (C) by removing screws (D).
2. Determine desired location for light xture on wall. Hold mounting plate (A) in a
level position against the wall. Using a pencil, mark the location of the mounting
holes in mounting plate (A) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so wall
anchors (M), provided, t snugly inside the opening. Insert wall anchors into drilled
holes.
4. Ax mounting plate (A) to the wall by threading mounting screws (L) through
holes in mounting plate (A) and into wall anchors (M).
5. Slide backplate (C) over mounting plate (A). Thread screws (D) back into holes
at the top and sides of backplate (C) to secure xture to the mounting surface.
6. Thread cord cover (F) into the bottom of the backplate (C). Thread cord cover (G)
onto cord cover (F).
7. Insert one 60W MAX. Type A, medium base bulb into socket (J) located inside
shade.
8. Adjust xture to desired positon by carefully rotating arm (K) at joint (L). Adjust
shade (J) to desired position by carefully rotating at joint (I).
9. Insert three prong plug (H) into wall outlet.
10. Control power to the xture by using the turn knob (O) located inside the top of
shade.
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER. IT
IS RECOMMENDED THAT A LICENSED ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (C) by removing screws (D).
3. Cut three prong plug (H) from the end of the electrical cord.
4. Remove cord covers (F) and (G) from the electrical cord. From the back side of backplate (C), pull the
electrical cord up through hole in the bottom of backplate.
5. Cut the cord to the desired length for making an electrical connection. At least six inches of wire will be
needed to make proper electrical connection.
6. Thread plug (E) into hole at the bottom of backplate (C).
7. Carefully pull the wiring from wall outlet box. Thread wires through the center hole in mounting plate
(A).
8. Ax mounting plate (A) to wall outlet box with mounting screws (B) provided.
9. Lift xture to mounting plate and make proper electrical connections described in steps 10-12. A
LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from xture to ground wire in the outlet box. Fasten
wires together with wire nut (O) and tightly wrap the connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten
wires together with wire nut (O) and tightly wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box.
Fasten wires together with wire nut (O) and tightly wrap connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide backplate (C) over mounting plate
(A).
14. Thread screws (D) into holes at the top and sides of backplate (C) to secure the xture to the mounting
surface.
15. Follow steps 7-8 from cord cover assembly instructions above.
16. Control power to the xture by using the turn knob (O) located inside the top of shade.
567
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety
instructions are read before beginning installation of xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn o power at switch before replacing bulbs, making sure xture has had
sucient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
* This xture is UL rated for dry locations.
ASSEMBLY INSTRUCTIONS FOR YOUR
VORTEX WALL SCONCE
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners. *
(A)
(B)
(C)
(D)
(E)
(G)
(H)
(I)
(J)
(K )
(L)
(M)
(N)
(O)
(O)
(F)