Installation Guide

3391
ASSEMBLY INSTRUCTIONS:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX/ CIRCUIT BREAKER.
2. Remove all parts from carton. Do not throw away any parts.
3. Remove shade (N) by carefully removing clips (L) and releasing shade (N) from shade housing (K). Set shade (N) and clips (L)
aside.
4. Remove quick link (G) from hang straight (F). Keep quick link (G) attached to chain (H).
5. Remove cross bar (A) (with threaded tube (C) and hang straight (F) attached) from canopy (D). Do this by unthreading collar (E)
from hang straight (F). Canopy (D) will slip over hang straight (F). Set the canopy (D) and collar (E) aside.
6. Ax cross bar (A) (with threaded tube (C) and hang straight (F) attached) to ceiling outlet box using screws (B) provided.
7. Measure desired drop for xture to hang and add/remove chain links (H) with chain break tool (not included).
8. Thread loop (J) onto shade housing (K). NOTE: Make sure wiring is pulled tight when threading parts together to prevent damage
to the wire.
9. Attach quick link (I) to extension loop (J).
10. Slip collar (E) over chain (H) so it rests on loop (J). Slip canopy (D) over chain (H) so it also rests on loop (J).
11. Lift xture to ceiling and secure quick link (G) to hang straight (F). Guide the wire exiting the xture through the center of collar
(E) and canopy (D). Continue to guide the wire through chain (H), quick link (G) and through the center of hang straight (F) and
threaded tube (C).
12. Make proper electrical connections described in steps 13 - 15. A LICENSED ELECTRICIAN IS RECOMMENDED.
13. Attach ground wire from xture (green or silver in color) to ground wire from outlet box. Fasten wires together with wire nut (O)
and tightly wrap connection with electrical tape.
14. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire
nut (O) and tightly wrap connection with electrical tape.
15. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with
wire nut (O) and tightly wrap connection with electrical tape.
16. Carefully push wire connections back into ceiling outlet box.
17. Slide canopy (D) up chain (H) and hold ush against ceiling. To secure position of canopy (D), slide collar (E) up the chain and
thread it onto hang straight (F). Turn until hand tight.
18. Install one 150W max Type A, medium base bulb into the socket.
19. Before attaching the shade to the xture, note the stickers located at every notch (M) on shade. Notice the stickers on housing (K)
and on clips (L). Shade notches must be aligned with corresponding sticker on housing. Stickers on clips must correspond to the
shade and housing stickers. For example, the housing sticker labeled with a number 1 will line up with the notch that is labeled
with a number 1 sticker. The clip labeled with a number 1 sticker will then be used to fasten the two together. Note: misaligning
the stickers or using a clip that does not match may result in an incorrect t which could cause the shade to fall.
20. Lift shade (N) up to shade housing (K), making sure corresponding stickers are aligned. Secure shade (N) to the shade housing (K)
by attaching the bottom of clip (L) under the lip of shade (N) at notch (M). Push clip (L) into place over the rim of shade housing
(K). Repeat for remaining clips (L).
21. Reconnect main electrical supply from the fuse box/ circuit breaker and test the xture.
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It is very important that they are read completely before beginning the installation of
your xture.
* WE STRONGLY RECOMMEND INSTALLATION BY A LICENSED ELECTRICIAN.
* Turn o power at switch before replacing bulbs, making sure xture has had sucient time to cool down.
* If any special control devices are used with this xture, follow the instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualied electrical contractor.
* This xture is U.L. rated for dry locations.
ASSEMBLY INSTRUCTIONS FOR YOUR
BRIGHTON PENDANT
***To clean, use soft cloth only. Do not use any chemical or abrasive cleaners.***