Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (C) from backplate (E) by removing screws (G).
2. Determine desired location for light xture on wall. Hold mounting plate
(C) in a level position on desired wall location. Using a pencil, mark the
location of the mounting holes in mounting plate (C) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so
they accommodate wall anchors (L), provided. Insert wall anchors into
drilled holes.
4. Afx mounting plate (C) to the wall by threading mounting screws (D)
through holes in mounting plate (C) and into wall anchors.
5. Slide backplate (E) over mounting plate (C). Thread screws (G) into vacant
holes at the top and bottom of backplate (E) to secure xture to the
mounting surface.
6. Thread cord cover (M) into nipple (I) at the bottom of the backplate.
Thread cord cover (N) on to cord cover (M).
7. Remove ange (A) from threaded socket (F).
8. Place shade (B), onto threaded socket (F).
9. Thread ange (A) onto socket (F) to secure the shade to the xture.
10. Insert one (1) 60W MAX. Type A, medium base bulb into socket.
11. Insert three prong plug (O) into wall outlet.
12. Use switch (H) to control power to lamp.
6. Carefully unscrew nipple (I) from backplate (E). Thread plug (J) into hole vacated by the electrical cord and nipple (I).
7. Carefully pull the wiring from wall outlet box. Thread the wires through the center hole in mounting plate (C).
8. Afx mounting plate (C) to wall outlet box with mounting screws (D) provided.
9. Make proper electrical connections described in steps 10 - 12. A LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from xture to ground wire in the outlet box. Fasten wires together with wire nut (K) and tightly
wrap the connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut (K) and
tightly wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (K)
and tightly wrap connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide backplate (E) over mounting plate (C). Thread screws (G) into vacant holes at
the top and bottom of backplate (E) to secure the xture to the mounting surface.
14. Remove ange (A) from threaded socket (F).
15. Place shade (B), onto threaded socket (F).
16. Thread ange (A) onto socket (F) to secure the shade to the xture.
17. Insert one (1) 60W MAX. Type A, medium base bulb into socket.
18. Reconnect main electrical supply from the fuse box/circuit breaker and test xture.
19. Use switch (H) to control power to lamp.
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners as they may damage the nish. *
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER. IT IS RECOMMENDED THAT A
LICENSED ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (C) from backplate (E) by removing screws (G).
3. Cut three prong plug (O) from the end of the electrical cord.
4. From the back side of backplate (E), pull the electrical cord up through
nipple (I).
5. Cut the cord to the desired length for making electrical connection. At least
six inches of wire will be needed to make proper electrical connection.
1806
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety
instructions are read before beginning installation of xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn off power at switch before replacing bulbs, making sure xture has
had sufcient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
ASSEMBLY INSTRUCTIONS FOR YOUR
REAL SIMPLE WALL SWINGER
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(I)
(J)
(K)
(L)
(M)
(N)
(O)
(H)