Installation Guide

TILT THE BOTTOM OF THE MIRROR SLIGHTLY SO THAT THE PADS
CAN BE PLACED WITHIN 1/2" TO 1" OF THE BOTTOM AND SIDE.
PRESS THE MIRROR FIRMLY INTO THE PAD. BE SURE MIRROR IS
CORRECTLY SEATED ON CLIPS AND IN THE PROPER POSITION
BEFORE SECURING PADS.
MIRROR
PADS
WALL
E. FINAL FIT UP AND CARE OF YOUR MPM / MPS WALL MIRROR AND SHELF SYSTEM.
1. WITH THE CABINETS ON EITHER SIDE OF THE LOCATION OF THE MPM / MTM MIRROR, TEST FIT THE MIRROR.
2. IF THE CABINETS NEED TO BE REPOSITIONED SLIGHTLY A. WHEN SURFACE MOUNTED, LOOSEN THE TOP CLIPS
SLIGHTLY AND SLIDE CABINETS LEFT OR RIGHT. B. WHEN RECESSED, LOOSEN THE 4 SCREWS SECURING THE
CABINET IN THE ROUGH OPENING - REPOSITION THE CABINET AND RETIGHTEN THE SCREWS. DO NOT OVERTIGHTEN.
3. PEEL THE PAPER BACKING FROM THE 2" X 2" ADHESIVE PADS AND PLACE THEM UNDER THE BOTTOM OF THE
MIRROR AS SHOWN BELOW:
4. INSTALL THE SHELF INTO THE BRACKETS AND TIGHTEN THE NYLON SET SCREWS.
5. UNDER NO CIRCUMSTANCES SHOULD AN AMMONIA OR VINEGAR BASED CLEANER BE USED ON MIRRORS. USE ONLY A
LINT FREE POLISHING CLOTH SLIGHTLY DAMPENED WITH WATER OR RUBBING ALCOHOL IF NECESSARY TO REMOVE
STUBBORN STAINS.
6. IF YOU SHOULD HAVE ANY PROBLEMS WITH YOUR MPM / MTM WALL MIRROR SYSTEM PLEASE CONTACT YOUR
ROBERN DEALER. FOR OTHER QUESTIONS RELATING TO YOUR INSTALLATION CONTACT THE FACTORY AT:
ROBERN, INC. 215 826.9800
701 N. WILSON AVE 800 877.2376
BRISTOL, PA 19007 FAX [phone]
7. PLEASE REFER TO THE PARTS LIST BELOW TO CORRECTLY IDENTIFY ALL PARTS.
D. INSTALLING THE MPS SHELF SYSTEM.
1. BEFORE INSTALLING THE CABINETS THE MPS SHELF BRACKETS MUST BE INSTALLED ON EACH CABINET ADJACENT
TO THE MPM / MTM MIRROR. THE BRACKETS ATTACH TO THE CABINET USING THE EXISTING SCREWS IN THE FRAME.
2. BE SURE THE OPEN SIDE OF THE BRACKET FACES THE MPM / MTM MIRROR. INSTALL THE CABINET, (LIGHT IF USED) AND
SIDE KIT AS PER C ABOVE.
REMOVE THESE SCREWS FROM
CABINET AND REATTACH WITH MPS BRACKET
DO NOT REMOVE THIS SCREW
SIDE AT BOTTOM
OF MP / MT CABINET
MPS SHELF
BRACKET
GLASS SHELF
FITS HERE.
D. INSTALLING THE MPS SHELF SYSTEM.
PARTS LIST MPM WALL MIRROR
E. FINAL FIT UP AND CARE OF YOUR MPM / MTM WALL MIRROR AND MPS SHELF SYSTEM.
MPM
FIRST 2 NUMBERS = WIDTH
LAST 2 NUMBERS = HEIGHT
LAST TWO LETTERS =
SHAPE:
A = ARCH TOP
F = FLAT TOP
EDGE:
B = BEVELED EDGE
P = POLISHED EDGE
PAGE 2
SS477 REV. 6/2010
#10 X 2" SCREWS
"Z" CLIPS
WASHERS
WALL ANCHORS
2" X 2"ADHESIVE PADS
PARTS LIST MPS SHELF
MPS BRACKETS
MPS _____ SHELF
MODEL NUMBER IS LENGTH OF SHELF LESS 2"
(MPS23 IS 25" LONG)
MPS_____L SHELF (FOR USE WITH M-L1.5 LIGHTS)
MODEL NUMBER IS LENGTH OF SHELF LESS 5"
(MPS23L IS 28" LONG)
MPS_____HL SHELF (FOR USE WITH M-L3.5 LIGHTS)
MODEL NUMBER IS LENGTH OF SHELF LESS 9"
(MPS23HL IS 32" LONG)
NYLON SET SCREWS
1/4-20 X 1/4"
MTM
FIRST 2 NUMBERS = WIDTH
LAST 2 NUMBERS = HEIGHT
LAST TWO LETTERS =
SHAPE:
A = ARCH TOP
F = FLAT TOP
EDGE:
B = BEVELED EDGE
P = POLISHED EDGE
NOTE 4:
WHEN USING AN
MPS SHELF IN A
STACKING SYSTEM
REFER TO SHEET
SS499 FOR
MOUNTING
INSTRUCTIONS.
THE MPS SHELF
FOR STACKING HAS
THE SUFFIX "F" AND
IS ONLY AVAILABLE
IN A 4" DEPTH FOR
D6 OR D8 CABINETS
ONLY.