COLOR SPOT 575 Version 1.
COLOR SPOT 575 Table of contents 1. Safety instructions ........................................................................................................ 4 2. Operating determinations ............................................................................................. 5 3. Description of the device .............................................................................................. 6 4. Installation ...................................................................................
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this device have to: - be qualilfied - follow the instructions of this manual Caution ! Be careful with your operations.
2. Operating determinations This device is a moving-head spot for creating decorative effects and was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Never run the device without lamp! Do not shake the device. Avoid brute force when installing or operating the device.
3.
4. Installation 4.1Fitting the lamp DANGER ! Install the lamps with the device switched off only. Unplug from mains before ! To insert the lamp OSRAM HSR 575/2 95V/575W GX-9,5 or PHILIPS MSR 575/2 95V/575W GX-9,5 , MSD 575 95V/575W GX-9,5 loosen the lamp cover at the rear of head (see the drawings ) by remowing the 3 fastening screws which are marked "X,Y,Z".Carefully pull out the cover with the lamp socket assembly.If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket.
4.2 Lamp adjustment: 3 adjustment screws "A,B,C" The COLOR SPOT 575 lampholder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance. Strike the lamp,open the shutter and the iris,set the dimmer intensity onto 100% and focus the light on a flat surface (wall).Center a hot-spot(the brightest part of the image) by using the 3 adjustment screws "A,B,C".
4.4 Rigging the fixture Danger of fire ! When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in between a distance of min. 0,5 m. Warning ! Use 2 clamps to rig the fixture on the truss. Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
4.5 Connection to the mains Connect the fixture to the mains with the enclosed power-plug. The earth has to be connected! The occupation of the connection-cables is as follows: Cable Pin International Brown Live L Blue Neutral N Yellow/Green Earth 4.6 DMX-512 connection/connection between fixtures The wires must not come into contact with each other, otherwise the fixtures will not work at all, or will not work properly.
5.
Channel Channel 16 bit 9 10 11 Value Function Type of control 8 bit 7 8 9 120-127 128-255 White Enable macro color function on channel 7 0 1- 63 64 65-127 128-255 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-199 200-207 208-215 216-223 224-231 232-239 240-247 248-255 3-facet prism rotatin control,Prism macros Open position (no prism) Forwards rotation from fast to slow No rotation Backwards rotation from slow to fast Prism/gobo macros Macro 1 Macro 2 Macro 3 Macro 4 Macr
Channel Channel 16 bit 8 bit 12 10 13 11 14 12 15 13 16 14 Value Function Type of control 0-127 128-190 191-192 193-255 Rotating gobo index,rotating gobo rotation Gobo indexing Forwards gobo rotation from fast to slow No rotation Backwards gobo rotation from slow to fast proportional proportional step proportional 0 1-179 180-191 192-223 224-255 Iris Open Max.diameter to min.
6. Addressing The control board on the front panel of the COLOR SPOT 575 allows you to assign the DMX fixture address, which is defined as the first channel from which the COLOR SPOT 575 will respond to the controller. If you set, for example, the address to channel 5, the COLOR SPOT 575 will use the channel 5 to 20 for control. Please, be sure that you dont have any overlapping channels in order to control each COLOR SPOT 575 correctly and independently from any other fixture on the DMX data link.
7.5 Rotating gobo wheel The rotating gobo wheel includes 3 metal gobos, 1 glass gobo and 2 dichroic gobos rotating in both directions, indexable, rotating gobo wheel continuousli rotation from slow to fast. The rotating gobos can be interchanged. 7.6 3-facet rotating prism The 3-facet prism rotating in both directions at different speeds,16 prism-gobo macros 7.7 Iris Motorized adjustable iris,variable pulse effects. 7.
DMX 512 Address settings The letter "A" flashes. Use the [Up] and [down] keys to select required address (001 - 497) and press [Enter] to confirm or [Mode] to cancel and return to the main menu. Pan reverse This function allows you to invert the pan movement. Use the [Up] and [Down] keys to select "On" if you wish this feature or "Off" if you dont wish this feature and press [Enter] to confirm or [Mode] to cancel and return to the main menu.
Demo sequences This function allows you to run a special demo-test sequences without an external controller, which will show you some possibilities of using COLOR SPOT 575. Press [Up] and [Down] keys to select the "Mod1" or "Mod2" sequences. The "Mod1" is suitable for projections on the wall, ceiling or ground without any head-movement, the "Mod2" uses all COLOR SPOT 575 functions and therefore is good for a complete introduction of the fixture. Reset Function Press [Enter] key to run reset.
Manual control of effects This function allows you to control manually the channel functions of the fixture. Use the [Up] and [Down] keys to select desired function and press [Enter] to adjust the effect or [Mode] to cancel and return to the menu. Lamp On automatically This menu allows you to turn the lamp On after switching the fixture On and switch On/Off the lamp light sensor. Lamp On after switching the fixture On This function enables to turn the lamp On automatically after switching the fixture On.
DMX values Readout DMX values of each channel received by the fixture. Use the [Up] and [Down] keys to select desired channel and press [Enter] to read its value coming to the fixture or [Mode] to cancel and return to the menu. Display adjusting This function allows you to adjust the display settings: Display intensity By this function you can adjust from 20% to 100% the display intensity .
PAN/TILT feedback This function allows to return the mowing head to the required position after changing the position by external force (e.g.by stroke). Use the [Up] and [Down] keys to select "On" if you wish to anable this function or "Off" if you wish not to return the mowing head to the required position and press [Enter] to confirm or [Mode] to cancel and return to the menu.
low/high speed of the fan operating The fan keeps the adjusted low speed until the temperature exceeds max. inside temperature of the fixture, then the COLOR SPOT 575 automatically switch from low to high the fan speed. continuous controlling of the fan speed without the DMX value This mode is similar to "reG", but the initial level of the fan speed can´t be adjusted by the DMX. Default settings Press [Enter] to reset all fixture personalities (not the adjusting functions) to the default values.
1. Calibration via the control board Press [Enter] and the [Up] and [Down] keys in order to display the following messages: "Col1, Col2, SGob, rGob,Grot" for very smooth function calibration. Select one of them, press [Enter] and use the [Up] and [Down] keys in order to adjust their right value from 0 to 255. Then press [Enter] to confirm or [Mode] to cancel and return to the menu. This can be repeated for each calibration parameter if it is required.
9. Error and information messages HEAt This message appears if you try to switch on the lamp within 5 minutes after having switched it off (the lamp is too hot). The message will appear on the display if the lamp doesn't ignite within 28 seconds. The COLOR SPOT 575 will store this information and automatically ignite the lamp when the 5 minutes period has expired.
PoEr This message will appear if the fixture was shortly disconnect from the main. PAEr (PAN-yoke movement error) This message will appear after the reset of the fixture if the yokes magnetic-indexing circuits malfunction (sensors failed or magnet missing) or the stepping motor is defective. (Or its driving IC on the main PCB). The yoke is not located in the default position after the reset.
Static gobos: - 9 static metal-gobos plus an open position - static gobo wheel cont. rotation Rotating gobos: - 6 interchanged gobos plus an open position:3 metal gobos, 1 glass gobo and 2 dichroic gobos rotating in both directions at different speeds - Gobo indexing - Rotating gobo-wheel cont. rotation - Outside diameter 27 mm, image diameter 23 mm.
Pan/Tilt: -Pan movement range 530° -Tilt movement range 280° -8/16 bit movement resolution -Automatic Pan / Tilt position correction -Maximum PAN-movement 530° in 2.65 s -Maximum TILT-movement 280° in 1.
The gobos may be cleaned with a soft brush. The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet. The dichroic colour-filters, the gobo-wheel and the internal lenses should be cleaned monthly. To ensure a proper function of the gobo-wheel, we recommend lubrication in six month intervals. The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo-wheel rotates.